better bathrooms BeBa-27691 Zorah Tall Basin Mixer User Manual

better bathrooms BeBa-27691 Zorah Tall Basin Mixer

Thank you for choosing Better Bathrooms.
Please read this manual before installing your product and keep for future reference.

Product Information

The product is a Zorah Tall Basin Mixer available in three different finishes: Matt Black (model BeBa_27691), Brushed Brass (model BeBa_27692), and Brushed Gunmetal (model BeBa_27693). It is designed to be installed in bathrooms and is part of a range of bathroom products offered by the manufacturer.

This product is manufactured by one of the UK’s largest independent bathroom stores and has received several awards for its quality and innovation. The company aims to provide extraordinary bathroom products at affordable prices, offering a wide range of modern and traditional style ceramics, fixtures, fittings, and furniture.

Product Usage Instructions

Installation

1. Install the two inlet hoses (6C) into the faucet (6A) by hand tightening them.
2. Fit the Fixing bar (6B) into the mixer body and tighten it.
3. Ensure that the rubber washer (15) is placed between the mixer and the basin/top.
4. From above the basin, push the inlet hoses (6C) and fixing bar (6B) through the hole on the basin and position them correctly. Make sure not to kink or twist the hoses.

Operation

1. From underneath the basin, secure the mixer body (7A) by placing the Rubber Washer(7F) and Metal Washer(7B) onto the Fixing Bar (6B), followed by the Fixing Nut (7C). Tighten the Fixing Nut(7C) until the mixer is secure. Avoid overtightening as it may crack the ceramic.
2. Check that the washers are fitted into the nut on the hot and cold flexible hoses. Connect the hot and cold flexible hoses to the isolation valves (not included), with the hot hose on the left and the cold hose on the right.
3. Turn on the water supply and check for any leaks.

Product Troubleshooting

If you encounter any issues with the product, refer to the following troubleshooting guide:

• Poor water flow: Check for any blockages in the aerator or inlet pipes. Clean or replace if necessary.
• Water leak: Inspect all connections and fittings for any signs of leakage. Tighten or replace as needed.
• Handle loose: Ensure that the screw (2) holding the handle (1) is tightened properly.
• Body loose: Check the fixing nut (7C) underneath the basin and tighten if necessary.

Product Maintenance

To keep the surface of your product in good condition, follow these maintenance instructions:

• Use a clean damp cloth to wipe the surface of the product.
• Avoid using abrasive cleaning agents or materials.
• If any harsh chemicals come into contact with the surface, rinse and wipe clean immediately.

Single-person assembly
Tools required
We always recommend using professional tradespeople to install your product

Congratulations on your purchase

And welcome to our growing gang of savvy shoppers We’re on a mission to bring you extraordinary bathroom products, for less. From modern to traditional style ceramics, plus the gorgeous fixtures, fittings and furniture to match. So, you can fall in love with your space every single day.

As one of the UK’s largest independent bathroom stores, we’ve received countless awards; including the National Business Awards UK, the Digital Entrepreneur Awards and being placed on The Sunday Times Fast Track 100. We hope your new product goes above and beyond your expectations. However, should any problems occur, please:

• log in to your account and contact our customer services team via your self-serve portal – betterbathrooms.com/CustomerAccount/Login
• contact us via betterbathrooms.com/content/contact-us

Important information

• Please read these instructions thoroughly and retain for future reference
• Installation must be carried out in compliance with The Water Fittings Regulations and Scottish Water Byelaws.
• The system must be flushed prior to installation
• Minimum and Maximum working pressure : 0.5 – 5 bar
• Pressures must be equal for optimum performance
• Please do not connect hot and cold water supply lines in reverse. This could result in hot water flowing from cold line and cause scalding.
• The feed-water temperature of water shall not exceed 85°C. Exceeding 85°may cause scalding, the service life of faucets might be shortened, or the faucet might be damaged.
• After installation, please make sure the faucet is securely mounted and checked for leaks.

Parts / Diagrams

| No| Part Description
---|---|---
1| Handle
2| Screw
3| Cap
4| Trim Cover
5| Locknut
6| Cartridge
7| Cartridge base
8| Screw
9| O-ring
10| O-ring
11| Inlet pipe
12| Body
13| Aerator
14| Aerator key
15| Rubber washer
16| Flexible hose
17| Fixing kit

Dimensions

Tools required

• Spanner

Installation

• Install the two inlet hoses(6C) into the faucet(6A), these should only be hand tightened.
• Next fit Fixing bar (6B) into the mixer body and tighten.
• Ensure the rubber washer (15) is fitted between mixer and basin/top
• From above basin, push the inlet hoses(6C) and fixing bar (6B) through the hole on basin and position correctly.
• Do not allow the hoses to be kinked or twisted

| From underneath basin, secure mixer body (7A) by placing Rubber Washer(7F), Metal Washer(7B) onto the Fixing Bar (6B), followed by Fixing Nut (7C).

Tighten Fixing Nut(7C) until mixer is secure, do not overtighten as this could crack the ceramic

---|---
| Check the washers are fitted into the nut on the hot and cold flexible hoses.

Connect the hot and cold flexible hoses to the isolation valves (not included), hot on the left, cold on the right.

Turn on water supply and check for leaks.

Operation

Troubleshooting

operator

·         Is the flexible hose kinked or twisted

·         Was the system flushed prior to installation

·         Is the mixer cartridge free from debris

Water leak| ·         Is there damage or dirt within the O-rings of the cartridge

·         Is there damage or dirt with the rubber washers in the of aerator

·         Is the locknut on top of the cartridge fully tightened

·         Is there damage within the rubber washer inside the nuts of flexible hoses

·         Is there damage with the O-rings on the flexible hoses

Handle loose| ·         Is the screw inside the handle fully tightened

·         Is the locknut on top of cartridge fully tightened

Body loose| ·         Is the fixing kit underneath fully tightened

Maintenance

Replacement of Cartridge

CLEANING OF AERATOR

• To avoid the dust and impurities from construction that might influence the water flow, it is suggested to clean the aerator on a regular basis.

Cleaning

• To maintain the surface of your product, wipe with a clean damp cloth and wipe dry, do not use any abrasive cleaning agents or materials.
• If any harsh chemicals come into contact with the surface of the product, rinse and wipe clean immediately.

For more information

• visit: betterbathrooms.com
• email: customerservices@buyitdirect.co.uk
• call: 03303903062
• write to Trident Business Park, Neptune Way, Huddersfield, HD2 1UA

References

• Better Bathrooms - Login

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>