GWFM-1114-1 Gate Way by Race LLC Instruction Manual
- June 12, 2024
- RACE
Table of Contents
GWFM-1114-1 Gate Way by Race LLC
Product Information
Product Name: Gate-Way
Model Number: GWFM-1114-1
Manufacturer: RACE LLC
Product Usage Instructions
Important Information If you have trouble lights on the dash before you install the Gate-Way, you will continue to have them after you install the Gate-Way. The codes are kept in the body control module and the only way to clear them is through the factory ECU first.
Before you install the Gate-Way, please be aware of the following:
- 2011-2014 Mustang GT: You will lose traction control and cruise control
- 2013-2014 Mustang GT with premier dash: You will lose Cyl. temp/trans temp and one touch start
- Automatic cars that wish to retain the 6R80 trans will need to purchase a US shift controller and a Race US-1114 harness
Instructions for 2011-2014 Mustang GT
- VIN: Must have Vin or fault codes will show on dash.
- MPH adjustment: Good start is 28 for 3.31 gears and 26 for 3.73. Adjust if needed.
- Odometer adjustment: Should be 43 for 3.31 gears and 48 for 3.73. Adjust if needed.
- Type of transmission: Choose Manual or Automatic.
How to Mount the Gate-Way
- Put the Dominator or Terminator X Max into the stock ECU bracket. The bracket will have to be removed and modified to install the Dominator. The Terminator X Max will fit right in. You can drill a support hole if you wish.
- Now slide the Vi-TCT under the fuse box with the part # facing the fender. Make sure you have plenty of length of the factory harness.
- Take the Gate-Way unit with the RACE sticker up and plug it into the factory connector. Make sure the C is in the center.
- Take the Gate-Way and slowly work and flip it over so Holley EFI connector faces the front of the car and the trap door is facing up.
- Plug the Gate-Way harness into the Vi-VCT, then into the Holley EFI. It is best to lift up Hollley ECU and start with the bottom plugs first and work up. Don’t forget the Power cable.
- Loop the main Gate-Way connector and plug it into the blue connector.
- If you wish to monitor or adjust from the Manifold Air Temp sensor, you will need to get a Motorcraft DY 1159 MAT sensor. You will need to remove one guide on the Dy-1159 sensor for it to plug into the connector labeled MAT.
- The Gate-Way and harness is a tight fit but it will all fit into place.
Important Information
If you have trouble lights on the dash before you install the Gate-Way, you
will continue to have them after you install the Gate-Way. The codes are kept
in the body control module and the only way to clear them is through the
factory ECU first.
Before you install the Gate-Way. You should know. 2011-2014 Mustang GT: You
will lose traction control and cruise control 2013-2014 Mustang GT with
premier dash: You will lose Cyl. temp/trans temp and one touch start.
Automatic cars that wish to retain the 6R80 trans will need to purchase a US
shift controller and a Race US-1114 harness.
INSTRUCTIONS
INSTRUCTIONS: 2011-2014 Mustang GT
- Download Gate-Way software off a RACE’s website. Raceproductsusa.com
- Use the mini USB to a micro USB harness included to connect and program the Gate-Way. The Gate-Way will power up off of your laptop so you can be programing the Gate-Way before it is installed into your car.
- To program. You will need to set the:
- VIN: Must have Vin or fault codes will show on dash.
- MPH adjustment: Good start is 28 for 3.31 gears and 26 for 3.73. Adjust if needed.
- Odometer adjustment: Should be 43 for 3.31 gears and 48 for 3.73. Adjust if needed.
- Type of transmission: Choose Manual or Automatic.
HOW TO MOUNT THE GATE-WAY
The Gate-way will set in front of the ECU under the plastic cover. Start with
removing the factory ECM. Before you remove the ECM, get a silver felt tip
marker and mark the center connector on the ECU connector with a C. This needs
to be done because the two larger connectors can be interchanged and you do
not want to get them switched. Take the two bolts out of the factory ECU and
remove it from the bracket. Take the three connectors that plug into the
factory ECU and follow the wiring back to the main harness. You will see that
the ECU harness has mounts on both sides of the fuse box. Remove the harness
from those mounts. That will give you more length in the harness to help
install the Gate-Way where it should go.
Put the Dominator or Terminator X Max into the stock ECU bracket. The bracket
will have to be removed and modified to install the Dominator. The Terminator
X Max will fit right in. You can drill a support hole if you wish. Now slide
the Vi-TCT under the fuse box with the part # facing the fender.
Make sure you have plenty length of the factory harness. Take the Gate-Way
unit with the RACE sticker up and plug it into the factory connector. Make
sure the C is in the center.
Take the Gate-Way and slowly work and flip it over so Holley EFI connector
face the front of the car and the trap door is facing up Plug the Gate-Way
harness into the Vi-VCT then into the Holley EFI. Best to lift up Hollley ECU
and start with the bottom plugs first and work up. Don’t forget the Power
cable. Loop the main Gate-Way connector and plug into the blue
connector.
Hook up the loose black (ground) and the red (power) wires to the battery
terminals.
The only things left are:
Plug in a 1 to 3 bar MAP sensor to the connector labeled MAP or use the
internal 1 bar on Terminator X Max. Fine a good vacuum source off the intake
to hook the MAP sensor to.
If you are using the Holley Terminator X MAX ECU, that will work with the
existing factor 4.9 Ford wideband. Plug the connector that is labeled WB to
the connector that is labeled 4.9 WB to use the factory 4.9 WB.
If you are using the Holley EFI Dominator ECU, you must change one of the
factory WB to a 554-100 NTK wideband and plug that into the connector marked
WB.
If you wish to monitor or adjust from the Manifold Air Temp sensor, you will
need to get a Motorcraft DY 1159 MAT sensor. You will need to remove one
guides on the Dy-1159 sensor. For it to plug it into the connector labeled
MAT.
The Gate-Way and harness is a tight fit but it will all fit into place
Once you have the harness and Gat-Way installed. You will see you have five
loose wires.
- CAN – is used to connect to ECU for tuning or optional 3.5 monitor / Dash
- Power Tap- is a ground, sensor ground,12 volts & 5 volts for Optional I/O
- FUEL- Holley 100 psi fuel pressure sensor (Optional for Holley to monitor)
- Oil- Holley 100 psi pressure sensor (Optional for Holley to monitor. Ford oil sensor is just a oil switch)
- I/O- Inputs/ Outputs (Optional) see below
NOTE 1: When setting up your tune in the Dominator or Terminator X Max.
You must set up the basic I/O as grounds as follows TerminatorXMax Fan 1 J1B
B10, Fan 2 J1B B3, AC IAC Kick J1A A12, AC Shutdown J1B B12. Dominator Fan 1
J1B B10, Fan 2 J1B B3, AC IAC Kick J1A A12, AC Shutdown J3 B12
NOTE 2: In the I/O connector E,G & H are already connected to fans, IAC
kick & AC shutdown. Do not use E, G & H for anything else.
NOTE 3: Holley EFI has a safety on the DBW throttle body. If you wish to
apply the brakes to do a burn out, you will have to install a toggle switch on
B24 wire coming out of the J3 connector to switch the safety off and on.
NOTE 4: If you need to do a Terminator X or Holley EFI firmware upgrade
using the CAN connection. You will need to turn the Gate-Way CAN off. You can
do this by turning the ignition key on (Do not start). Holding down the brake
and fuel pedal down at the same time. The wrench light will blink until it
goes solid. The Gate -Way CAN is now off. Now do your firmware upgrade. Then
turn key off and on. The Gate-Way CAN is back on.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>