PARIS TEXAS HARDWARE Wall Mount Track System Installation Guide
- June 12, 2024
- PARIS TEXAS HARDWARE
Table of Contents
PARIS TEXAS HARDWARE Wall Mount Track System Installation Guide
INTRODUCTION:
PTH™ 1 3/8″ R-TEC Automation® Metal Traverse Systems are used to electronically control the drapery using a Slim Drapery Motor and Remote Control. By using a Remote Control or the R-TEC Automation® App via a smartphone or tablet, the operator can open and close the drapery smoothly and precisely. The maximum width for this system is 12′ continuous (in select finishes) and 24′ spliced. The minimum width for this system is 37″. The maximum drapery weight is 77 lbs. Single or double system.
BRACKET ASSEMBLY:
-
PTH™ 1 3 /8″ R-TEC Automation® Metal Traverse Systems can be mounted on the wall or ceiling.
-
Wall options include single brackets with either a 3 1 /2″ or 6″ projection, or a double bracket with 3″ and 7 1 /2″ projections.
-
Ceiling options include a single or double bracket with 2 3 /8″ drop, or a lowprofile ceiling bracket with a 5 /32″ drop.
PARTS LIST:
Basic Components:
- R-TEC Automation® Metal Track
- Brackets
- Slim Drapery Motor
- Li-ion Battery power option
- AC / DC Power Transformer power option
BRACKET PLACEMENT:
It’s recommended to use 1 bracket beside each pulley and an adjacent bracket no more than 24″ away. On the remaining part of the Metal Track, bracket-to- bracket distances should be no more than 48″. Also, 1 bracket should be placed on each side of a splice if used.
INSTALLATION
We recommend using a professional installer. Installation hardware is included. The fasteners (screws and mollies) may not be appropriate for every installation or wall material. Brackets and holdbacks should be installed securely into wall studs when possible. Paris Texas Hardware™ will not assume responsibility for damages incurred by improperly mounted or inadequately supported hardware.
WALL MOUNT TRACK SYSTEM INSTALL:
NOTE: Installer is responsible for determining the correct mounting fastener and wall location per the wall construction type.
Step 1. Locate bracket base plate.
Step 2. Mount wall mount base plate to wall.
Step 3. Locate bracket base cover. Place cover over wall mount base
plate. Turn cover clockwise to lock in place.
Step 4. Locate track system. Place track system onto the wall mount base
plates.
Step 5. Tighten all wall mount stems with set screw located above the
wall mount cover.
CEILING MOUNT TRACK SYSTEM INSTALL:
NOTE: Installer is responsible for determining the correct mounting fastener and wall location per the wall construction type.
Step 1. Locate ceiling plate.
Step 2. Mount ceiling plate to ceiling.
Step 3. Locate ceiling bracket cover. Place cover over the ceiling plate.
Step 4. Locate the insert. Screw the insert on the ceiling plate.
Step 5. Locate track system. Place track system onto the ceiling mount
inserts.
Step 6. Tighten all ceiling mount stems with set screw located close to
the ceiling mount cover.
LOW-PROFILE CEILING BRACKET TRACK SYSTEM INSTALL:
NOTE: Installer is responsible for determining the correct mounting fastener and wall location per the wall construction type.
Step 1. Locate track system and mount it to the ceiling.
NOTE: The Low-Profile Ceiling Mount Bracket is already attached to the
track.
NOTE: Glides can be added or removed with the Drive Pulley installed by
removing the End Stop.
Install the Pendant into the End Stop.
Install the End Stop.
How to get started using your PTH™ 1 3 /8″ R-TEC Automation® Metal Traverse System:
- Please read all the instructions provided with your Slim Drapery Motor.
- Your motor will be shipped in “sleep mode” and must be woken up before using.
- You will need a remote control or a smartphone to set up and control your Slim Drapery Motor.
- Only use power options for your motor that are available through Rowley Company
References
- Home | Paris Texas Hardware
- rowleycompany.scene7.com/is/content/rowleycompany/pth-metal-product-instruc-motor-rtec-center-one-way-drawpdf