serville classics OFF16026 AIRLIFT Pro Electric Adjustable Desktop Converter Desk Instruction Manual
- June 12, 2024
- serville classics
Table of Contents
AIRLIFT® Pro Electric Adjustable
Desktop Converter
Model #: OFF16026/7
Thank you for choosing Seville Classics! We hope that you enjoy your new sit- to-stand desk. Please read through this user guide for parts list, instructions, frequently asked questions and contact information.
Parts List
A. AIRLIFT® Desk (1)
B. Brackets (2)
C. Tray (1)
D. Allen Wrench (1)
E. Wire Clip (4)
F. Screws (6)
G. Adapter (1)
Required Tools (not included)
|
---|---
Please make sure you have all the parts on this list.
If you’re missing parts, contact us for replacements at
800-323-5565 or send an email to
Support@SevilleClassics.com
Use Instructions
- Locate controller on right side of desk.
FAQS
Q. Can I attach a monitor stand to it? What about dual monitors?
A. Yes! Be sure the desk is below it’s 33 lbs. maximum weight limit.
Q. What size is the base?
A. Base measures 32.75 inches wide and 22 inches deep.
Q. Do I need to plug it in?
A. Yes! Works with any 120V outlet.
Specifications
Dimensions: 35.43″ W x 23.23″ D x (5.9″ to 19.7″) H
Maximum weight on tray: 5 lbs. (2 kgs)
Maximum weight capacity overall: 33 lbs. (15 kgs)
USB Power: 2.1 amps @ 10 watts
Safety
Failure to follow these instructions may result in property damage or personal injury
| DO NOT place devices on desk edge.
---|---
| DO NOT route wires through desk legs.
| MAKE SURE devices have cables long enough for the full-range
(15 in/38 cm) of height-adjustment.
| DO NOT quickly lift desktop when loaded.
Assembly Instructions
STEP 1. Remove AIRLIFT® DESK (A) from box and set on flat table. Weighs
50.7 lbs.
STEP 2. Cut the plastic ties on both sides of the
AIRLIFT® DESK (A). STEP 3. Plug ADAPTER (G) cable into cable attached to
desk motor. Plug ADAPTER (G) into wall socket.
STEP
4. Press the UP button on the controller to lift the AIRLIFT® DESK
(A).
STEP 5. Flip TRAY (C) upside down. Attach BRACKETS
(B) to underside of TRAY (C) with SCREWS (F) and screwdriver. 
STEP 6. Hook BRACKETS (B) over the bolts on the inner legs
of the AIRLIFT® DESK (A).
Tighten bolts clockwise with included ALLEN WRENCH (D).
Cable Management
ALWAYS route your ADPTER (G) through the REAR of the desk.
NEVER route cables through the legs of the desk.
Stick the
WIRE CLIP (E) to back of the crossbar.
Use these clips to route cables from keyboards, mice and monitors through the
REAR of the desk.
NOTE: This equipment has been tested and found to comply with the limits
for Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouragedto try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced Radio/TV technician for help
Customer Service Information
Telephone: 800-323-5565
Fax: 310-533-3899
Hours: 8:30 AM – 4:30 PM (PST)
Email: Support@SevilleClassics.com
Homepage: www.SevilleClassics.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>