ELITE SCREENS GSP0810-IPW350 GolfSim Portable ImpactWhite 350 User Guide

ELITE SCREENS GSP0810-IPW350 GolfSim Portable ImpactWhite 350

Product Information

GolfSim Portable Series Sports Simulation Impact/Projector Screen

Thank you for choosing the GolfSim Portable projection screen! Please read through this user guide before utilizing the screen. Correct usage and maintenance will ensure a long product life.

Care & Use Instructions

Elite Screens highly recommends two people to assemble the GolfSim Portable screen. Make sure to distinguish the front and back of the impact/projection screen when setting it up. The backside has the Velcro. Follow the instructions in the screen assembly section to assure the front side is set up properly. Be sure to use the screen only during a light breeze (up to wind speeds of 7 mph); it is not meant to withstand heavy winds.

• Elite Screens is not responsible for damages due to negligence resulting from misuse under weather conditions and will void your warranty.Dust, dirt, and scratches on the projection surface will affect the picture quality, please take note of the points below to prevent that from occurring:

1. Do not touch the projection surface with your hands.
2. Do not write or draw on the projection surface.
3. Do not point at the projection surface with your fingers or sharp objects; this will damage the screen.

To avoid damage and injury, the screen should only be operated by adults.

Product Usage Instructions

Installation Tips and Precautions

We consider our impact screens a wearable item, and the life of them will vary according to their use.

1. Make sure to allow proper distance for swing range to protect children, pets, ceilings, walls, windows, or any other property.
2. Avoid using golf balls with scuffs or markings to maximize the life of your ImpactWhiteTM 360 screen. If possible, use new golf balls.
3. Never place the screen over a window or under constant sun exposure. Solar radiation from direct sunlight destroys the synthetic fibers of the screen.

Assembly Instructions

Before assembling the screen, make sure all the below components are included

• A: Top Folding frame x 1
• B: Bottom Folding frame x 1
• C: Left Folding frame x 1
• D: Right Folding frame x 1
• E: M8 Knob screws x 8
• F: Impact golf screen material x 1
• G: Top Enclosure Cover x 1
• H: Left Enclosure Cover x 1
• I: Right Enclosure Cover x 1
• J: Ball Bungees x 6 (2pcs with shorter cord)
• K: Velcro Strips x 12
• L: Protection sheet x 1
• M. Gloves x 2

Follow the assembly diagram below:

Thank you for choosing the GolfSim Portable projection screen! Please read through this user guide before utilizing the screen. Correct usage and maintenance will ensure a long product life.

Care & Use Instructions

• Elite Screens highly recommends two people to assemble the GolfSim Portable screen.
• Make sure to distinguish the front and back of the impact/projection screen when setting it up. The backside has the Velcro. Follow the instructions in the screen assembly section to assure the front side of is set up properly.
• Be sure to use the screen only during a light breeze (up to wind speeds of 7 mph); it is not meant to withstand heavy winds.
  • Elite Screens is not responsible for damages due to negligence resulting from misuse under weather conditions and will void your warranty. Dust, dirt and scratches on the projection surface will affect the picture quality, please take note of the points below to prevent that from occurring:
  1. Do not touch the projection surface with your hands.
  2. Do not write or draw on the projection surface.
  3. Do not point at the projection surface with your fingers or sharp objects; this will damage the screen material.
  4. Use a soft bristle brush or dry microfiber cloth to remove dust from the screen surface.
  5. Do NOT use any solutions, chemical cleaning agents, alcohol, or abrasive to clean the screen surface.
  6. When cleaning the projection surface, use a soft cloth dampened with warm water to remove any traces.
  7. Do NOT rub or apply pressure when cleaning the surface.
  8. Use a fabric steamer no higher than Polyester setting to remove any wrinkles or folds in the material.
• After using the screen, disassemble it and store it in the carrying bag provided.
• To avoid damage and injury, the screen should only be operated by adults.

Product Description

• Design : The aluminum frame is designed to be light weight and easily operated making it easy to carry, assemble and disassemble.
• Screen Fabric: The screen fabric is attached to the rectangular frame and held in place by Velcro strips, which ensure an evenly stretched and flat surface. The ImpactWhite™ screen material is durable and can be folded many times without causing damage or distortion to the surface.

Installation Tips and Precautions

We consider our impact screens a wearable item and the life of them will vary according to their use.

1. Make sure to allow proper distance for swing range to protect children, pets, ceilings, walls, windows, or any other property.
2. Avoid using golf balls with scuffs or markings to maximize the life of your ImpactWhite™ 360 screen. If possible, use new golf balls.
3. Never place the screen over a window or under constant sun exposure. Solar radiation from direct sunlight destroys the synthetic fibers of the screen.

Hardware and Parts list

A: Top Folding frame x 1| B: Bottom Folding frame x 1| C:    Left Folding frame x 1
---|---|---
| |
D:      Right Folding frame x 1| E: M8 Knob screws x 8| F: Impact golf screen material x 1
| |
G: Top Enclosure Cover x 1| H: Left Enclosure Cover x 1| I: Right Enclosure Cover x 1
| |
J: Ball Bungees x 6| K: Velcro Strips x 12| L: Protection sheet x 1

• 2pcs with shorter cord

| |

M. Gloves x 2|

Note: Before assembling the screen, make sure all the above components are included.

Assembly diagram

Frame assembly

1. Take the frames out of the carrying bag, unfold and place them on the protection sheet (L) as shown below.
   

2. Fasten the frame pieces together at all four locations as shown above using the knob screws (D)

LOCK CENTER JOINTS AND CORNER HINGES

• Center Joints: Unfold the frame until the latch on the hinge “clicks” into place.

  • TIP: Gently lift the frame to ensure the hinge is locked (button pops up).
    

• Corner Hinges: Unfold the frame’s corner hinges until they “click” into place.
  

CAUTION: BE AWARE OF PINCH POINTS.

Impact Screen, Left/Right/Top Enclosure Cover Assembly

1. Please follow below instructions to place the screen material before assembly, and make sure the screen material back side facing up.
   Note: The impact screen has Velcro (soft fuzzy side) on Top edge. This is the back side of the impact screen.

2. Attach the Impact golf screen material (F) on the frame with Velcro with Gloves (M).
   

3. Left (H) and Right (I) side enclosure cover assembly.
   

4. Prepare the enclosure covers for attachment to the frame by identifying the front and back.
   Note: The black side faces in, and the silver side faces out.

5. Aligned velcro the enclosure cover to the inside of the small side frame from bottom to top.

6. Velcro the enclosure cover and impact material together after aligning their edges.

Top enclosure cover (G) assembly.

(A) Attach Left and Right sides

• Align and velcro the enclosure cover to the outer side of the small side frame from bottom to top.
• Stretch the enclosure cover to reach the right side.
• Pull the enclosure cover tightly and velcro it to the outer side of the frame.
  

(B) Attach Top side
Attach Impact Screen and Top/Right/Left enclosure panels

1. Lift the frame gently with the help of two people.
   CAUTION: Make sure all leg hinges are locked before lifting the assembled frame to standing position.
   

2. Attach the Left/Right enclosure cover (H / I) to secure on the bottom of the frame legs.
   

3. Install Ball Bungees (J) and attach the Impact screen (F) to the enclosure covers.
   

Impact screen surface tension and flatness adjustment
Wrap tie six Velcro strips (K) on each vertical side frame evenly as instructed below to pull the impact screen material to tension it.

• Wrap one end of the velcro strip on the vertical frame with the soft fuzzy side facing in.

• Open the edge of the materials and attach the other side of the velcro strip.
  

• Seal the edge tightly between the enclosure cover and screen material to secure the velcro stip.

• Turn in the direction of the arrow to tighten the velcro strip. Inspect the impact screen for surface flatness and adjust as needed.
  

Finished!
Disassembly and repack into bag
Please follow the installation instruction to disassemble the components. And refer below instruction to place the components into bag.

For local Elite Screens contact or Technical Support, please visit www.elitescreens.com

References

• Cinema Quality Projector Screens | Elite Screens
• Cinema Quality Projector Screens | Elite Screens

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>