Yealink BH71 Bluetooth Headset User Guide
- June 12, 2024
- Yealink
Table of Contents
Bluetooth Headset
BH71/BH71 Pro
Quick Start Guide (V1.1)
NEED MORE HELP?
|
---|---
Technical support https://ticket.yealink.com| FAQ & User manual
http://support.yealink.com
BH71 Package List
BH71 Pro Package List
Note: Some third-party accessories may be incompatible
Charge Headset
It takes approximately 90 minutes to fully charge the headset.
Charging Indicator
- Carrying Case
Charging: Solid green Charging is complete: Off
- Charging Case
Charging: Flash green Charging is complete: Off
Power on/off
Pair and Connect
Slide and hold the switch for 3 seconds until the LED indicator flashes red
and blue automatically. 
Note:
The BT51A Bluetooth Dongle of BH71 Pro is pre-paired to the headset and ready
for use.
One headset can only connect to two devices at a time.
The BT51A can only connect to one headset at a time.
Fit the Headset
• Right ear wearing
- Take out the headset, as shown in figure❶ . Twist the speaker to the left, and then rotate microphone boom down.
- Before wearing, you can adjust the height of the speaker up or down to get the perfect fit for your ear.
- Put the ear tip in your ear and slide headset over and behind your ear, then press gently toward your ear. Fine- tune the headset according to your own situation. Note: Remove your eyeglasses before donning the headset for best fit.
• Left ear wearing
- Take out the headset, as shown in figure❶ . Twist the speaker to the right, and then rotate microphone boom down.
- For wearing methods, please refer to steps 2 and 3 of the right ear wearing.
Note: Change the ear tip for a better fit. Ear tips with three size options — S/M/L (M is pre-installed).
Call Control
| Accept
---|---
| Reject (It is not applicable to Teams)
| End
| In the idle status, invoke the Teams client
| In the idle status, activate Cortana (requires Microsoft’s support)
Software Management
• Yealink USB Connect
Download it from the Yealink website https://www.yealink.com/product/yuc.
Note: It needs to be used with Yealink USB Connect of version 0.35.x.x or
later.
• Yealink Connect App
Download the Yealink Connect App from IOS App Store or Android App Store.
Apple and the Apple logo are trademarks of Apple Inc.
Regulatory Notices
Operating Ambient Temperatures
Operating temperature: 0 °C to +40 °C (+32 °F to +104°F)
Relative humidity: 5% to 90%, noncondensing
Storage temperature:-30°C to +70°C (-22 to +158°F)
Warranty
Our product warranty is limited only to the unit itself, when used normally in
accordance with the operating instructions and the system environment. We are
not liable for damage or loss resulting from the use of this product, or for
any claim from a third party. We are not liable for problems with Yealink
device arising from the use of this product; we are not liable for financial
damages, lost profits, claims from third parties, etc., arising from the use
of this product. Explanation of the symbols
DC symbol
is the DC voltage symbol.
WEEE Warning symbol
To avoid the potential effects on the environment and human health as a result
of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should understand
the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as
unsorted municipal waste and have to collect such WEEE separately.
Restriction of Hazardous Substances Directive (RoHS)
This device complies with the requirements of the EU RoHS Directive.
Statements of compliance can be obtained by contacting
support@yealink.com.
Safety Instructions
Save these instructions. Read these safety instructions before use!
General Requirements
Before you install and use the device, read the safety instructions carefully
and observe the situation during operation.
During the process of storage, transportation, and operation, please always
keep the device dry and clean, avoid collision and crash.
Please attempt not to dismantle the device by yourself. In case of any
discrepancy, please contact the appointed maintenance center for repair.
Please refer to the relevant laws and statutes while using the device. Legal
rights of others should be respected as well.
Environmental Requirements
Place the device at a well-ventilated place. Do not expose the device under
direct sunlight.
Keep the device dry and free of dust.
Do not place the device on or near any inflammable or fire-vulnerable object,
such as rubber-made materials.
Keep the device away from any heat source or bare fire, such as a candle or an
electric heater.
Operating Requirements
Do not let a child operate the device without guidance.
Do not let a child play with the device or any accessory in case of accidental
swallowing.
Please use the accessories provided or authorized by the manufacturer only.
The power supply of the device shall meet the requirements of the input
voltage of the de vice.
Please use the provided surge protection power socket only.
Before plugging or unplugging any cable, make sure that your hands are
completely dry.
Do not spill liquid of any kind on the product or use the equipment near
water, for example, near a bathtub, washbowl, kitchen sink, wet stationment or
near a swimming pool.
During a thunderstorm, stop using the device and disconnect it from the power
supply. Unplug the power plug and the Asymmetric Digital Subscriber Line
(ADSL) twisted pair (the radio frequency cable) to avoid lightning strike.
If the device is left unused for a rather long time, disconnect it from the
power supply and unplug the power plug.
When there is smoke emitted from the device, or some abnormal noise or smell,
disconnect the device from the power supply, and unplug the power plug
immediately.
Contact the specified maintenance center for repair.
Do not insert any object into equipment slots that is not part of the product
or auxiliary product.
Before connecting a cable, connect the grounding cable of the device first. Do
not disconnect the grounding cable until you disconnect all other cables.
Battery Requirements
Do not immerse the battery into water, which could short-circuit and damage
the battery.
Do not expose the battery to an open flame or leave the battery where it could
be subjected to extremely high temperatures, which could cause the battery to
explode.
Do power the handset off before removing the battery.
Do not try to use the battery for the power supply of any device other than
this handset.
Do not open or mutilate the battery, released electrolyte is corrosive and may
cause damage to your eyes or skin.
Use only the rechargeable battery pack delivered with the handset or those
rechargeable battery packs expressly recommended by Yealink.
Defective or exhausted battery should never be disposed of as municipal waste.
Return old battery to the battery supplier, a licensed battery dealer or a
designated collection facility. |
Cleaning Requirements
Before cleaning the device, disconnect it from the power supply.
Use a piece of soft, dry and anti-static cloth to clean the device.
Keep the power plug clean and dry.
Troubleshooting
The unit cannot supply power to Yealink device.
There is a bad connection with the plug.
- Clean the plug with a dry cloth.
- Connect it to another wall outlet.
The usage environment is out of operating temperature range.
- Use in the operating temperature range.
The cable between the unit and the Yealink device is connected incorrectly.
- Connect the cable correctly.
- You cannot connect the cable properly.
- You may have connected a wrong Yealink device.
- Use the correct power supply.
- Some dust, etc., may be in the port.
- Clean the port.
- Contact your dealer or authorized service facility for any further questions.
FCC CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
ISED WARNING
This device complies with Innovation, Science and Economic Development Canada
licenceexempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
The device is compliance with RF exposure guidelines, users can obtain
Canadian information on RF exposure and compliance.
EU Regulatory Information
Support Frequency Bands and Power:
Bluetooth 2.4GHz<20dBm
Contact Information
YEALINK NETWORK TECHNOLOGY CO.,LTD.
No.666 Huan Rd. Hula District Xiamen City, Fujian, P.R. China
YEALINK (EUROPE) NETWORK TECHNOLOGY B.V.
Strawinskylaan 3127, Atrium Building, 8th floor, 1077ZX
Amsterdam, The Netherlands
YEALINK (USA) NETWORK TECHNOLOGY CO., LTD.
999 Peachtree Street Suite 2300, Fulton, Atlanta, GA, 30309, USA
Made in China
Declaration of Conformity
We,
YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD
Address: No.666 Huan Rd. Hull District Xiamen City, Fujian, P.R. China
Manufacturer: YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD
Address: No.666 Huan Rd. Hull District Xiamen City, Fujian, P.R. China
DATE: 28th/November/2022 declare that the product
Type: Carrying Case
Model: BHC71
meets the essential requirements and other relevant provisions according to
the following EC directive
Directive: 2014/30/EU, 2014/35/EU
Conformity
The product complies with the following standards:
Safety: EN IEC 62368-1:2020+A11:2020
EMC: EN 55032:2015+A1:2020
EN 55035:2017+A11:2020
EN IEC 61000-3-2:2019+A1:2021
EN 61000-3-3:2013+A2:2021
Directive 2011/65/EU and (EU) 2015/863 of the European Parliament and of
the Council of 8 June 2011 and 4 June 2015 on the restriction of the use of
certain hazardous substances in electrical and electronic equipment(RoHS2.0)
Directive 2012/19/EU of the European Parliament and of the Council of
4.July.2012 on Waste electrical and electronic equipment (WEEE)
Regulation (EC) No.1907/2006ofthe European Parliament and of the Council
of 18.December.2006 on Registration, Evaluation, Authorization, and
Restriction of Chemicals (REACH)
Declaration of Conformity
We,
YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD
Address: No.666 Huan Rd. Hula District Xiamen City, Fujian, P.R. China
Manufacturer: YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD
Address: No.666 Huan Rd. Hull District Xiamen City, Fujian, P.R. China
DATE: 280/November/2022 declare that the product Type: Charging Case
Model: BHC71P
meets the essential requirements and other relevant provisions according to
the following EC directive
Directive: 2014/30/EU, 2014/35/EU Conformity The product complies with
the following standards:
Safety: EN IEC 62368-1:2020+A11:2020
EMC: EN 55032:2015+A1:2020
EN 55035:2017+A11:2020
EN IEC 61000-3-2:2019+A1:2021
EN 61000-3-3:2013+A2:2021
Directive 2011/65/EU and (EU) 2015/863 of the European Parliament and of
the Council of 8 June 2011 and 4 June 2015 on the restriction of the use of
certain hazardous substances in electrical and electronic equipment(RoHS2.0)
Directive 2012/19/EU of the European Parliament and of the Council of
4.July.2012 on Waste electrical and electronic equipment (WEEE)
Regulation (EC) No.1907/2006 ofthe European Parliament and of the Council
of 18.December.2006 on Registration, Evaluation, Authorization, and
Restriction of Chemicals (REACH) 
Declaration of Conformity
We, YEALINK(XIAMEN) NETWORK TECIINOLOGY CO.,LTD
Address: No.666 titian Rd. Hull District Xiamen City, Fujian, P.R. Chita
Manufacturer: YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD
Address: No.666 Hu’an Rd. Hula District Xiamen City, Fujian, P.R. Chiai
DATE: 28th/November/2022 declare that the product Type: Bluetooth Headset
Model: BHM711
meets the essential requirements and other relevant provisions according to
the following EC directive
Directive: 2014/30/EU, 2014/35/EU, RED 2014/53/EU
Conformity
The product complies with the following standards:
Safety: EN IEC 62368-1:2020+A11:2020
EMC: EN 55032:2015+A1:2020
EN 55035:2017+A11:2020
EN IEC 61000-3-2:2019+A1:2021 EN 61000-3-3:2013+A2:2021
ETSI EN 301 489-1 V2.2.3 (2019-11)
ETSI EN 301 489-17 V3.2.4 (2020-09)
Radio: ETSI EN 300 328 V2.2.2 (2019-07)
Health: EN 62479:2010; EN50663:2017
Directive 2011/65/EU and (EU) 2015/863 of the European Parliament and of
the Council of 8 June 2011 and 4 June 2015 on the restriction of the use of
certain hazardous substances in electrical and electronic equipment(RoHS2.0)
Directive 2012/19/EU ofthe European Parliament and of the Council of
4.July.2012 on Waste electrical and electronic equipment (WEEE)
Regulation (EC) No.1907/2006 ofthe European Parliamentand of the Council
of 18.December.2006 on Registration, Evaluation, Authorization, and
Restriction of Chemicals (REACH)
Addl.- 309, 3rd Floor, No.16, Yun Ding North Road,
Hull District, Xiamen City. Futon, P.R.China
Tel: +86-592-5702000
Fax: +86-592-5702455
About Yealink
Yealink (Stock Code: 300628) is a global-leading provider of Unified
Communication & Collaboration Solutions specialized in video conferencing,
voice communications, and collaboration, dedicated to helping every person and
organization embrace the power of “Easy Collaboration, High Productivity”.
With best-in-class quality, innovative technology, and user-friendly
experiences, Yealink is one of the best providers in more than 140 countries
and regions, ranks No.1 in the global market share of IP Phone, and is the Top
5 leader in the video conferencing market (Frost & Sullivan, 2021).
Technical Support
Visit Yealink WIKI (http://support.yealink.com/) for the latest firmware,
guides, FAQ, Product documents, and more. For better service, we sincerely
recommend you to use Yealink Ticketing system (https://ticket.yealink.com)
to submit all your technical issues.
| Bluetooth Headset
---|---
Model: BHM711
Input:5V 0.2A| FCC ID：T2C-BHM711
IC：10741A-BHM711
<http://www.yealink.com>YEALINK(XIAMEN) NETWORK TECHNOLOGY CO., LTD.
Web: www.yealink.com
Copyright©2022 YEALINK(XIAMEN) NETWORK TECHNOLOGY
CO.,LTD. All rights reserved.
References
- Yealink Support
- Yealink Support "Yealink Support")
- Yealink Support
- Yealink Ticket
- Yealink | UC & C Terminal, Video Collaboration, Conference Phone, IP Phone, Headsets & Video Conferencing
- Yealink | UC & C Terminal, Video Collaboration, Conference Phone, IP Phone, Headsets & Video Conferencing
- USB Connect | Yealink
- Yealink Ticket
- USB Connect | Yealink
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>