CANOPIA 87383 Martinique 10 ft x 12 ft Gazebo Kit Instruction Manual

CANOPIA 87383 Martinique 10ft x 12ft Gazebo Kit

Product information

The Martiniquetm 10×12 / 3×3.6 is a product manufactured by Palram Industries Ltd. It is a recyclable and registered design product. For further assistance and support, you can visit the official website at www.canopia.com .

Product Usage Instructions

Before starting the assembly of the Martiniquetm 10×12 / 3×3.6, please read the following instructions carefully:

1. Make sure you have all the necessary parts and tools required for assembly.
2. Refer to the How to Assemble video guide provided on the website or by scanning the QR Code available at canopia.shop/Assemble-Martinique for a visual demonstration of the assembly process.
3. If you still have questions or concerns, you can seek further assistance at canopia.shop/support .
4. If local customer care is required, please refer to the user manual for contact information.

IMPORTANT

• Please read these instructions carefully before starting assembly.
• Keep these instructions in a safe place for future reference.

TOOLS & EQUIPMENT

• D 2 people needed
• Ladder
• Rubber Mallet
• Electric Drill with Drill Bit
  • 5mm |3/16″
  • 10 mm | 13/32″
• Wrench
  • 10 mm |13/32″
  • 13 mm |1/2″
• Spirit Level
• Cordless Drill Philips Head
• Philips Head Screwdriver
• Silicone

SITE PREPARATION & FOUNDATION

PREPARE THE SITE

The product must be positioned and fixed on a flat level surface.

1. Clear the site
2. Level the ground

CHOOSE YOUR FOUNDATION TYPE

Option 1: Concrete / Wooden surface

• The screws and masonry anchors supplied with the kit are suitable for concrete fixing only.
• Please consult with an expert regarding which fasteners are suitable for other surfaces types (not supplied).

CHOOSE YOUR FOUNDATION TYPE

• Dig holes into the ground and fill with concrete.
• For frozen areas, please check the required depth needed for these holes.

Option 2: Paving stones

• 10 cm / 4″ | b + c – 40 cm / 1’4″

Option 3: Solid ground / Asphalt

• 40 cm /14^ | b + c – 40 cm / 14″

DIMENSIONS

• The Illustration describes center-to-center distance between poles.

SAFETY ADVICE

• It is of utmost importance to assemble all of the parts according to the directions. Do not skip any steps.
• Always wear work gloves during panel sliding.
• Always wear shoes and safety goggles when working with extruded aluminium.
• If using a step ladder or power tools make sure that you follow the manufacturer’s safety advice.
• Do not touch overhead power cables with the aluminium profiles.
• Do not attempt to assemble the product in windy or wet conditions.
• Do not climb or stand on the roof.
• Dispose of all plastic bags. Keep them out of reach of small children.
• Keep children away from the assembly area.
• Do not lean against or push the products during construction.
• Do not position your product in an area exposed to excessive winds.
• Do not attempt to assemble this product if you are tired, have taken drugs or alcohol or if you are prone to dizzy spells.
• Hot items such as recently used grills, blowtorches etc. must not be stored in the product.
• Make sure there are no hidden pipes or cables in the ground before anchoring to foundation.
• This product is designed to be used mainly as a garden gazebo.
• Make sure to anchor the product directly to a solid foundation to increase the product’s stability and wind resistance in areas with severe weather conditions. Make sure that there are no obstructions between the assembly area and the final position of the product.

CARE & MAINTENANCE

• When your product needs to be cleaned, use a mild detergent solution and rinse with cold clean water.
• DO NOT use acetone, abrasive cleaners or other special detergents to clean the panels.
• Clean the product once assembly is complete.

BEFORE ASSEMBLY

• Selecting a site:
  • Choose your site carefully before beginning assembly.
  • Choose a sunny position away from overhanging trees.
  • The product must be positioned and fixed on a flat level surface.
• The product must be secured directly to a solid foundation.
• This is a multi-part assembly best achieved by two people. Allow at least half a day for the assembly process.
• Take all components & parts out of the packages. Sort the parts and check against the content parts list.
• Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.
• Please note that multi-sided profiles are used in this product. As a result some holes in the profiles are not used during assembly.
• Please review the entire instructions before starting. Carry out the assembly steps in exact order.
• Please consult your local authorities if any permits are required prior to constructing the product.
• Please ensure you have sufficient side space for inserting the roof panels during the assembly process.

IMPORTANT

• Firmly connect the product to a level surface immediately after completion of the assembly.
• Anchoring this product to the ground is essential to its stability and rigidity. It is required to complete this stage in order for your warranty to be valid.
• During assembly use a soft surface below the parts to avoid scratches and damages.
• We recommend checking for restrictions or covenants for building this product in your area.
• In addition we advise to check if you need to submit any forms or if any permit is required prior to building the product.

DURING ASSEMBLY

During assembly, you will encounter different icons for different products.

Please see below for more information:

• You may use silicone lubricant spray on the frame in order to help you slide the panels into the profiles. Do not spray the panels.
• Use a rubber mallet if necessary.
• Make sure you remove covering plastic film from both sides of the panel.
• All panels with the stamped words “THIS SIDE OUT” must be facing out to create full UV protection. Remove plastic sticker as panels are locked in place.
• This icon indicates that the installer should be inside the product.
• This icon indicates that the installer should be outside the product
• Steps marked with dashed outlines refer to Extensions only.
• Some of the steps are irrelevant for an assembly of a single product.
• When assembling a single or an extended product, some parts may be surplus.
• These 2 icons below indicate if screws tightening is required or not.
• Temporary tightening of a few screws may be needed to prevent a profile from sliding out.
• Tighten all screws once assembly is completed.

IMPORTANT ASSEMBLY STEPS

When encountering this information icon during assembly, please refer the relevant assembly step for important additional comments.

• Step 6b: Carefully spread silicone along the cross-section of the profile and immediately attach the profiles together. It is recommended to wipe the extra residue silicone
• Steps 7+12: It is recommended to use a carton or other soft material under the lowered corner in order to avoid scratches and peeling of paint.
• Step 10: Optional – if you wish to add Palram – Canopia’s Curtains or Netting Set, please thread the plastic clips through the rail in each profile. (Palram – Canopia’s Curtains / Netting Set are not supplied.
• Steps 12a+14a: Please note that screws insertion should be done from the outside.
• Steps 13+15: Please note that screws insertion should be done from the bottom up.
• Step 16a: Please add silicone on the inner area of part #8327 as illustrated.
• Step 17: Please use dry cloth to wipe the panel prior to attaching the sealing tape to the panels’ edges.
• Step 22a: Please drill holes in the panels to be located precisely parallel to the holes in the gutters’ profiles.
• Step 23: Please level the profile’s legs and adapt screws and plugs to your specific ground type.

Contents

Item/ Qty

Installation Instructions

LIMITED WARRANTY

PALRAM – CANOPIA | 10 YEAR LIMITED WARRANTY

Palram Canopia Ltd. (Company number: 512106824) whose registered office is at Teradion Industrial Park, M.P Misgav 2017400, Israel (“Canopia”) warrants that the product will be free from defects in material or workmanship for a period of 10 years from the original date of purchase.

• This warranty is valid only if the product is installed, handled, cleaned, and maintained in accordance with Canopia’s written specifications.
• This warranty does not cover defects resulting from normal wear and tear including, but not limited to: damage caused by use of force, incorrect handling, inappropriate use, negligence, accidents, impact from foreign objects, vandalism, pollutants, alteration, painting, damage resulting from cleaning with incompatible detergents or minor deviations of the product.
• This warranty does not apply to damage resulting from “acts of Nature”, which includes but is not limited to hail, storm, tornado, hurricane, blizzard, flood, or fire.
• Upon submitting proof of purchase and evidence of the claimed product failure, and subject to reporting the failure in writing within 30 days after discovery of the defect, Canopia, at its sole discretion, will replace defective parts of the Product, or refund you a prorated portion of the purchase price on a straight-line depreciated basis for the length of the warranty.

Declaration of Performance

According to Construction Products Council Directive UE N°305/2011 and EN 14963:2006

Issue Date 01/01/2022

1. Identification code: Martinique™, refer to CE label no 011
2. Type: A light transmitting self-supporting Twin-wall PC roofing structure with upstand made of aluminum and galvanized steel elements
3. Intended use: open multi-purpose covering where the ground slope is less then 5%
4. Manufacturer: Palram Canopia Ltd. Teradion Industrial Park, M.P Misgav 2017400, P.O.B. 53, Israel
5. Importer and EU representative: PALRAM Applications UK, Unit 40 |3 Industrial Estate Carr Hill, Doncaster DN4 8DE
6. Assessment and verification of constancy of performance: System 3
7. Declared performance:
   • Resistance to upward load: UL 400
   • Resistance to downward loads: DL 750
   • Reaction to fire: B, s1, dO
   • For mounting and fixing provisions see EN 16153:2013
   • Resistance to fire: NPD
   • External fire performance: FRooF
   • Water tightness:
   • For the rooflight with upstand: Pass
   • For the sheet material: Pass
   • Impact resistance:
   • For the small hard body: Pass
   • For the large soft body: NPD
   • Thermal transmittance:
   • For the rooflight: NPD (not relevant to an open multi purpose cover)
   • For the sheet material: 3.60 W/(m2•K)
   • Direct airborne sound insulation: NPD (not relevant to an open multi purpose cover)
   • Radiation transmittance:
   • Light transmittance: TV – 41.46%
   • Solar direct transmittance: Te – 43.6%
   • Solar factor: g value – 0.58
   • Air permeability:
   • For the rooflight: NPD (not relevant to an open multi purpose cover)
   • For the sheet material: Pass
   • Durability (of the sheet material): AA, Cu 1, Ku 1
8. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 7.
   • This declaration of performance is issued, in accordance with Annex ZA.2.2 – EN 14963:2006, under the sole responsibility of Palram Canopia Ltd.
   • ITT reports and Factor Production Control records are available upon request at www.canopia.com

Signed for and behalf of Palram Canopia Ltd. by:

• Teradion Industrial Park, Misgav
• 01/01/2022

Contact

Palram Canopia Ltd.

• Teradion Industrial Park, M.P Misgav 2017400, P.O.B 53, Israel
• Tel: +972.4.848.6900
• Fax: +972.4.848.6901
• canopia@palram.com
• www.canopia.com

HAVE A CONCERN?

WE CAN HELP.

• Before returning your purchase
  • Please take a look at our “How to Assemble” video guide. Scan the QR Code below or go to canopia.shop/Assemble-Martinique
• You didn’t find what you were looking for?
  • We can help at canopia.shop/support.
• WE ARE HERE TO HELP
  • For general questions: canopia.com/contact-us

USA

• 877-627-8476
• generalsupport@poly-tex.com

UNITED KINGDOM.  IRELAND

• 01302-380775
• customer.serviceUK@palram.com

AUSTRALIA

• 03-9219-4444
• salesvic@palram.com

CANADA

• 905-5646007
• sales@footprintproducts.com

GERMANY

• 0180-522-8778
• customer.serviceDE@palram.com

References

• Contact Us Archive - Canopia
• YouTube
• Support Archive - Canopia
• tex.com
• Inspection Systems for the Electronics Industry – Viscom – Viscom
• Αρχική Σελίδα - Alpaco Domica
• Canopia United Kingdom - Celebrate Outdoor Living

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>