OUTDOOR ESSENTIALS 181977 Tan Vinyl Fence Gate Instruction Manual

OUTDOOR ESSENTIALS 181977 Tan Vinyl Fence Gate

Product Information

The Somerset 6’x42″ Privacy Gate is a durable and secure gate designed for privacy fencing. The gate is made of high-quality materials and features a patented PicketLockTM technology for a glue and fastener-free connection between the pickets and rails. The gate dimensions are 68.5 inches in height and 41.5 inches in width.

TOOLS

Items you may need:

• Soapy water
• Non-marring rubber mallet
• Wooden wedge
• Power drill
• 1/4″ drill bit
• 7/16″ wrench
• Shims

NOTE: PicketLock™ is a patented technology that provides a glueand fastener-free connection between the pickets and rails. You may spray soapy water onto components to help them slide more easily into their corresponding channels. A non-marring rubber mallet may also be used to gently tap components more firmly into place.

PREPARATION

Check local ordinances and regulations before building your fence. Before construction, contact your local utility companies to mark any underground cables and pipelines. In addition, it is a good idea to discuss plans with any neighbors along your proposed fence line.

INSTALLATION

1. Step 1
   Take the bottom rail and align one of the pickets with the channel in the bottom rail. Slide the picket into the channel (fig. 1). Begin to insert the remaining pickets into the channel of the bottom rail (fig. 2). Because the pickets have a tongue-and-groove design, be sure to insert each in the same direction. Tightly align the tongue of each picket into the groove of the next one as they slide into the channel. Continue to slide the pickets to the opposite side of the bottom rail until all are inserted into the channel .

2. Step 2
   At the top of the gate assembly, slide the second rail over the top of the pickets (fig. 3).

3. Step 3
   Place gate jambs on both sides of the rails place the hinges on the gate jamb so they are aligned with the rails. Using the bracket as a guide, drill the four (4) necessary ¼” holes for the bracket bolts. Repeat these steps for the hinged brackets as well (fig. 4). Ensure the rails are fully inserted in the jamb before drilling. The bolts need to go through the jamb and rail to function properly. Slide the hinged bracket and bracket on the top and bottom of the gate jambs. Attach hinges to jambs with the supplied through bolts. Connect bolts with the supplied cap nuts. Ensure the gate is square before all bolts are tight. When square, tighten all bolts with a 7/16″ wrench.

Digging Post Holes
Dig post hole for the hinge post 18″ to 24″ in diameter and 36″ to 42″ deep (depending on local ordinance or expected frost depth in winter). We recommend that you insert a piece of 4×4 treated lumber to support the gate hinge post (fig. 5). Check measurement of gate. Actual width of the gate is 41-1/2″. The inside post-to-post dimension is 42-3/4″. This will give you a 5/8″ gap on both sides of the gate to the posts. DOUBLE-CHECK ALL MEASUREMENTS!

Installing the Gate

Measure to be sure you can install the gate to the post with approximately a 2″ gap from the ground to the bottom of the gate. Align the rails on the gate to the rails on the fence panels. Hang the gate between the posts. Use a 5/8″ spacer between the gate and the posts (fig. 6). Secure in place with shims under the gate or clamp the gate jamb to the post. Make sure the gate is level and square. Attach hinge brackets to the gate post with the provided screws (fig. 7). Remove any clamps and shims. Attach latch using screws provided (fig. 8). Install a post cap on each post using PVC cement or an exterior adhesive.

NOTE: The gate latch is designed to be used on the left- or right-hand side of the gate, depending on customer preference or design. The latch is assembled, ready to be installed on the right-hand side of the gate. If you desire to switch the latch follow these simple steps:

• Remove the 2 shoulder bolts and spring
• Change the orientation of the striker
• Reattach the spring and insert the shoulder bolts
• Shoulder bolts must be fully tightened. Thread-locking adhesive is recommended.

THE DIAGRAMS AND INSTRUCTIONS IN THIS BROCHURE ARE FOR ILLUSTRATION PURPOSES ONLY AND ARE NOT MEANT TO REPLACE A LICENSED PROFESSIONAL. ANY CONSTRUCTION OR USE OF THE PRODUCT MUST BE IN ACCORDANCE WITH ALL LOCAL ZONING AND/OR BUILDING CODES. THE CONSUMER ASSUMES ALL RISKS AND LIABILITY ASSOCIATED WITH THE CONSTRUCTION OR USE OF THIS PRODUCT. THE CONSUMER OR CONTRACTOR SHOULD TAKE ALL NECESSARY STEPS TO ENSURE THE SAFETY OF EVERYONE INVOLVED IN THE PROJECT, INCLUDING, BUT NOT LIMITED TO, WEARING THE APPROPRIATE SAFETY EQUIPMENT. EXCEPT AS CONTAINED IN THE WRITTEN LIMITED WARRANTY, THE WARRANTOR DOES NOT PROVIDE ANY OTHER WARRANTY, EITHER EXPRESS OR IMPLIED, AND SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING CONSEQUENTIAL DAMAGES.

©2022 UFP Retail Solutions, LLC. All rights reserved. Outdoor Essentials is a registered trademark of UFP Industries, Inc. PicketLock is a trademark of UFP Industries, Inc. | 2801 East Beltline NE, Grand Rapids, MI 49525 | 844-529-5882
OutdoorEssentialProducts.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>