Edvivi FFN7945BK 20 Inch Industrial Style Ceiling Fan User Guide
- June 12, 2024
- Edvivi
Table of Contents
- Edvivi FFN7945BK 20 Inch Industrial Style Ceiling Fan
- Warranty
- Pre-Installation
- SPECIFICATION
- TOOLS REQUIRED
- SAFETY PRECAUTION
- PARTS &ACCESSORIES
- Installation of the hanging bracket(suspension part)
- INSTALLATION INSTRUCTION
- Preparing for mounting
- TRANSMITTER FUNCTION
- **Transmitter holder
- Troubleshooting
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Edvivi FFN7945BK 20 Inch Industrial Style Ceiling Fan
Warranty
The supplier assures that The fan motor is from defects in workmanship and material present at the time of shipment from the factory for a lifetime after the date of purchase by the original purchaser. The supplier also warrants that all other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of. We agree to correct such defects without charge or at our option replace them with a comparable or superior model if the product is returned. To obtain warranty service, you must present a copy of the receipts and proof of purchase. All costs of removing and reinstalling the product are your responsibility. Damage to any part, such as by accident, misuse, improper installation or by affixing any accessories,is not covered by this warranty. Because of varying climatic conditions, this warranty does not cover any changes in brass finish, including rusting, pitting, corroding, or tarnishing. or peeling. Brass finish of this type gives their longest useful life when protected from varying weather conditions. A certain amount of “wobble”is normal and should not be considered a defect.
Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty hereby disclaims any and all warranties, including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty. Some states do not allow a limitation on how long an implied warranty lasts, so the above limitation may not apply to you. The retailer shall not be liable for incidental, consequential or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of products as part of a claim on the warranty must be paid by the customer.
Pre-Installation
SPECIFICATION
Size| Speed| Volts| Amps| Watts| CFM| RPM| Net Weight| Gross
Weight
| Cubic
Feet
---|---|---|---|---|---|---|---|---|---
20in
| Low|
120
| 0.21| 11.1| 465| 411|
10.5LB
4.8KG
|
15.2LB
6.9KG
|
5.0cu.ft.
Medium| 0.35| 30.5| 630| 616
High| 0.48| 58| 1310| 1205
The above data are for reference only, Actually, the motor speed of each
ceiling fan is a little different. Any products, Subject to actual products as
standard.
NOTE : These are approximate measures. They do not U Include the amps and
wattage used by the light kit. Specifications & measurements shown are subject
to± 5% variations.
TOOLS REQUIRED
SAFETY PRECAUTION
!IMPORTANT
- Do not connect this remote control ceiling fan to the regulator or dimmer switch.
- installation must be carried out by a qualified wiring installer.
- Turn off the electrical mains at the circuit breaker fuse box.
- Do not use a power supply other than 110-120V~ 60Hz.
- This appliance must be earthed.
- When mounting the fan, ensure that the safety wire is looped across the ceiling mounting hook.
- The ceiling mounting hook must be able to withhold a min. weight of 60kg.
- The ceiling fan must be mounted at a min. height of 7.5 feet/ 2.3m of clearance from the floor.
- Do not place any objects in the path of the blades.
- When all electrical connections are done, store all wires neatly.
- Make sure that all screws and connections are tightly screwed and secured.
- Children should be supervised to ensure that they do not play with the appliance.
- Ensure that the fan is switched off from the supply mains before removing the guard.
WARNING
This product is designed to use only those parts supplied with this product
and/or accessories designated specifically for use with this product. Using
parts and/or accessories not designated for use with this product could result
in personal injury or property damage.
NOTE: I Regulator Dimmer switch The illustrations in this manual are for
explanation purposes only and may differ from the actual unit. It is subject
to change without prior notice for further improvements
PARTS &ACCESSORIES
Installation of the hanging bracket(suspension part)
install a hanger on the ceiling For concrete ceilings, use the percussion bit with a diameter of 8mm to drill holes according to the length of expansion screws. Then use the attached expansion screws to fix the hanging bracket onto the ceiling (the selection is made according to the actual requirements of the customers).
STEP 2A-CONCRETE CEILING
SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.
- Use the Mounting Bracket (A) as a guide, and mark the spots where the 4 Expansion Bolts (B) will be drilled.
- Remove the Mounting Bracket (A), drill 4 holes, and insert 4 Expansion Bolts (2) into the concrete ceiling, install the mounting bracket and secure it with Flat Washers (C), Spring Washers (D), and Nuts (E).
IMPORTANT
SCREWS & NUTS MUST BE & tighten TILL SNUGFor wooden ceiling, use a wood screw
to drill on the wooden beam or the “junction box” to fix the hanging bracket
(selection is made according to actual requirements of the customers).
TEP 1A-WOODEN CEILING
SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.
- Use the Mounting Bracket (A) as a guide, and mark the spots where the 4 Self Tapping Screws (B) will be drilled.
- Remove the Mounting Bracket (A), drill 4 holes for 3MM diameter, and install the mounting bracket onto the wooden ceiling with the 4 Self Tapping Screws (B) & Washers (C).
IMPORTANT: SCREWS MUST BE TIGHTENED TILL SNUG
Remove the hanger from the motor.
Note: According to the ceiling of different materials, use different screws to fix the hanging bracket. Don’t fix the hanging bracket on the wood ceiling for less than 12MM to prevent danger caused by the loosening of screws. After the hanging bracket is completed, ensure that it can withstand the tension test of more than 68 kg for safety.
INSTALLATION INSTRUCTION
Install suspension system
- Let’s pass the ball/dwnrod assembly through the metal hook
- Let’s pass the ball/dwnrod assembly through the coupler cover.
- Finish.
Assembling the fan
WARNING : Failure to properly install the locking pin could result in the
fan becoming loose and possibly falling.
- Loosen, but do not remove, the two setscrews on the collar on top of the motor housing.
- Align the holes at the bottom of the down rod with the holes in the collar on top of the motor housing.
- Carefully insert the hanger pin through the holes in the collar and down rod. Be careful not to jam the hanger pin against the wiring inside the download.
- Insert the locking pin through the hole near the end of the hanger pin until it snaps into its locked position.
- Re-tighten the two set screws on the collar on top of the motor housing.
Selection of hanger pipes
- Use hanger pipes at an appropriate height based on the height of the ceiling.
- This ceiling fan is provided with the hanger pipe at the length of 10 inches and 20 inches.
- The bottom of the fan lamp must ensure 2.3 meters
Install suspension system
Remove the hanging pin and r-locking pin at the bottom choose the bulb that
closes act the role of the lifting pipe and set them aside for later use.
screw bulb inside the lamp holder. Let’s pass the down rod assembly through
the canopy. Pass the down rod assembly through the Coupler cover.
Install the bulbs
choose the bulb that closes and act the role screw bulb inside the lamp
holder.
Wiring diagram
WARNING: Each wire not supplied with this fan is designed to accept up to
one 12-gauge house wire and two wires from the fan.If you have larger than
12-gauge house wiring or more than one house wire to connect to the fan
wiring. Consult an electrician for the proper size of wire nuts to use.
WARNING : Remove the rubber motor stops on the bottom of a fan before
installing the blades or testing the motor.
IMPORTANT: Use the plastic wire connectors (BB) supplied with your fan.
Secure the connectors with electrical tape and ensure there are no loose
strands or connections.
Install remote control
- Carefully push the canopy to the bottom of the mounting bracket, make two sliding holes aligned to the two prominent screws on the mounting bracket, and then turn clockwise until tight.
- Push the canopy ring to the bottom of the canopy, slide the inner holes aligned to the two prominent screws on the mounting bracket again, and turn the canopy ring clockwise until tight.
Preparing for mounting
- Remove the mounting bracket from the canopy by loosening the two canopy screws located in the L-shaped slots.
- Remove and save the two canopy screws in the round holes. This will enable you to remove the mounting bracket
LIGHT ON/OFF
TRANSMITTER FUNCTION
Forward
The fan rotates anti-clockwise creating a downward airflow delivering a
cooling effect. Suitable for hot weather conditions or air-conditioned
conditions.
Reverse
The fan rotates clockwise creating an upward airflow and moving warm air off
the ceiling areas. This function works best at lower fan speed. Suitable for
cold weather or air-conditioned condition.
**Transmitter holder
**
Installing the Transmitter
holder install the transmitter holder to the wall or any flat surface with the
mounting screw provided.
Care and Cleaning
WARNING: Make sure the power is off before cleaning your fan.
- Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.
- Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor or the wood, or possibly cause an electrical shock. Use only a soft brush or lint-free cloth to avoid scratching the finish.
- The plating is sealed with a lacquer to minimize discoloration or tarnishing.
- You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish.
- You do not need to oil your fan. The motor has permanently lubricated sealed ball bearings.
Troubleshooting
Problem | Solution |
---|
The fan willn not start.
| □ Check the main and branch circuit fuses or breakers.
□ Check the line wire connections to the fan and switch wire connections in the switch housing.
The fan willn not start.
| □ Ensure all motor housing screws are snug.
□ Ensure the screws that attach the fan blade bracket to the motor hub are tight.
□ Ensure the wire nut connetions are not ratting against each other or the interior wall of the switch housing.
□ Allow a 24-hour “breaking in” period. Most noises associated with a new fan disappear during this time.
□ If you are using the Ceiling Fan light kit,ensure the screws securing the glassware are tight.Check that the light
□ bulbs are also secure.
□ Ensure the canopy is a short distance from the ceiling.It should not touch the ceiling.
□ Ensure your outlet box is secure and rubber isolator pads wereused between the mounting plate and outlet box.
The fan wobbles.
| □ Check that all blade and blade arm screws are secure.
□ Most fan wobble problems are caused when blade levels are unequal.Check this level by selecting a point on the
□ ceiling above the tip of one of the blades.Measure from a point on the center of each blade to the point on the
□ ceiling.Measure this distance.Rotate the fan until the next blade is positioned for measurement.Repeat for each
□ blade.Any measurement deviation should be within 1/8 in. Run the fan for ten minutes.If the fan continues to
□ wobble please contact Customer Service and a balancing kit will be sent to you
Thank you for purchasing our products.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>