In Common With Gemma Sconce Wall Light Instruction Manual
- June 12, 2024
- In Common With
Table of Contents
In Common With Gemma Sconce Wall Light
Product Information
The Gemma Sconce is a stylish and modern light fixture that adds a touch of elegance to any space. It comes with a Mudring, which is a mounting accessory that helps secure the fixture to the wall or ceiling. The sconce includes various components such as a backplate, mud ring, mounting screws, Wago clips, base screw, mounting bracket, G9 LED bulb, diffuser, and Gemma shade.
Product Usage Instructions
- Before starting the installation, make sure to turn off the electrical power at the main fuse box or circuit panel.
- Using a Phillips head screwdriver, mount the backplate (Part A) to the junction box by tightening the mounting screws (Part D). Ensure that the wires from the junction box remain accessible.
- Attach the mudring (Part B) to the backplate (Part A) using the two flat-head mounting screws (Part E).
- Apply drywall mesh tape (Part C) by overlapping it on the perimeter of the mud ring and the wall. Plaster over the drywall mesh tape, mudring, and wall. It is recommended to apply three coats of plaster, allowing each coat to dry and sand between coats. Ensure this area is painted before proceeding.
- Attach the mounting bracket (Part H) to the exposed part of the mudring (Part B) using additional mounting screws (Part D).
- Use the Wago clips (Part F) to connect the fixture’s wires to the corresponding wires from the junction box. Remember that white is neutral, black is live, and green/yellow is ground. Use a wire stripper if needed to remove 3/8 of the insulation from each wire before inserting them into the corresponding Wago clip (Part F).
- Slide the L base (Part I) over the mounting bracket (Part C).
- Secure the L base using the provided base screw (Part G).
- Carefully slide the Gemma shade (Part M) over the socket.
- Secure the shade (Part M) into place using the washer and provided tool (Part H).
- Push the included G9 LED bulb into a socket (Part K).
- Thread the diffuser (Part L) over the bulb.
- Turn the power back on at the main fuse box or circuit panel that was disabled before installation.
How to Install Your New Light
- Please check that you received all of the components pictured in this guide. Reach out to us if anything is missing. It’s very rare, but it happens. Don’t forget to turn off the electrical power source.
- Tools you will need that aren’t included: standard wire stripper, Phillips head screwdriver.
CAUTION
Electrical shock risk. Turn off electrical power at the main fuse box or
circuit panel before beginning installation, servicing the light, or
installing accessories. We recommend working with a qualified electrician
familiar with the type of work you’d like done.
Contents
Installation Instructions
- Step 1: Turn off electrical power at the main fuse box or circuit panel before beginning installation.
- Step 2: Mount the backplate (A) to the junction box using a Phillips head screwdriver to tighten the mounting screws (D). Make sure that the wires from the junction box are still accessible.
- Step 3: Attach the mudring (B) to the backplate (A) using the two flat head mounting screws (E).
- Step 4: Apply drywall mesh tape (C), overlapping the perimeter of the mud ring and the wall. Plaster over drywall mesh tape, mudring, and wall. We recommend applying three coats of plaster, allowing time for the plaster to dry and sanding between coats. Ensure this area is painted before proceeding to the next steps.
- Step 5: Attach the mounting bracket (H) to the exposed part of the mudring (B) using the additional mounting screws (D).
- Step 6: Use the wagon clips to connect the fixture’s wires to the corresponding wires from the junction box in the wall or ceiling. White is neutral; Black is live; Green/ Yellow is ground. One ground wire will be attached to the backplate, the other ground wire should come from the junction box. If needed use a wire stripper to remove 3/8” of the insulation from each wire before inserting them into the corresponding wage clip (F).
- Step 7: Slide L base (D) over the mounting bracket (C).
- Step 8: Secure using the provided base screw (G).
- Step 9: Carefully slide the Gemma shade (M) over the socket.
- Step 10: Secure the shade (M) into place using the washer and provided tool (H).
- Step 11: Push the included bulb into the socket (K).
- Step 12: Thread the diffuser (L) over the bulb. Turn the power back on at the main fuse box or circuit panel you disabled before installation.
Assembly Guide. incommonwith.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>