In Common With 7519624560810 Flora Chandelier Instruction Manual
- June 12, 2024
- In Common With
Table of Contents
In Common With 7519624560810 Flora Chandelier
Product Information
The Flora Chandelier is a stylish and elegant lighting fixture that will add a touch of sophistication to any room. It features a unique design with seven arms and comes with all the necessary components for installation. The chandelier includes a backplate, Wago clips, mounting screws, bulbs, shades, a canopy, and a stem.
Components
- Part A: Backplate
- Part B: Wago Clips (x3)
- Part C: Mounting Screws (x4)
- Part D: Bulb (x7)
- Part E: Shade (x7)
- Part F: Canopy + 7 Arm Stem
Product Usage Instructions
Installation Steps
- Turn off the electrical power at the main fuse box or circuit panel before beginning installation.
- Using a Phillips head screwdriver, mount the backplate (Part A) to the junction box by tightening the mounting screws (Part C).
- If the drop is over 36 inches, attach an additional stem to the chandelier.
- Gently slide the canopy cover down the stem (Part F).
- Secure the brass stem to the canopy base by rotating it clockwise.
- Use the Wago clips (Part B) to connect the fixture’s wires to the corresponding wires from the junction box. Match the wire colors – white is neutral, black is live, and green/yellow is ground. If needed, use a wire stripper to remove 3/8 of insulation from each wire before inserting them into the corresponding Wago clip.
- Mount the canopy base (Part B) into the backplate using a Phillips head screwdriver to tighten the mounting screws (Part C).
- Gently slide the canopy cover back up the stem (Part F) and rotate it clockwise to secure it firmly in place.
- Remove the protective paper from the canopy cover on the stem (Part F) and discard it.
- Carefully feed the shade (Part E) onto the end of each chandelier stem. Attach the shade by threading it clockwise. Repeat this step for all stems.
- Screw the included bulbs (Part D) into place.
- Turn the power back on at the main fuse box or circuit panel that was disabled before installation.
Please refer to the provided assembly guide images for visual assistance.
How to Install Your New Light
- Please check that you received all of the components pictured in this guide. Reach out to us if anything is missing. It’s very rare, but it happens. Don’t forget to turn off the electrical power source.
- Tools you will need that aren’t included: standard wire stripper, Phillips head screwdriver.
CAUTION
Electrical shock risk. Turn off electrical power at the main fuse box or
circuit panel before beginning installation, servicing the light, or
installing accessories. We recommend working with a qualified electrician
familiar with the type of work you’d like done.
Contents
Installation Instructions
Step 1: Turn off electrical power at the main fuse box or circuit panel before beginning installation.
Step 2: Mount the backplate (A) to the junction box using a Phillips head screwdriver to tighten the mounting screws (C).
Step 3: Attach an additional stem if the drop is over 36 inches.
Step 4: Gently slide the canopy cover down the stem (F).
Step 5: Secure the brass stem to the canopy base. Rotate the stem clockwise to secure it firmly in place.
Step 6: Use the Wago clips (B) to connect the fixture’s wires to the corresponding wires from the junction box in the wall or ceiling. White is neutral; Black is live; Green/ Yellow is ground. One ground wire will be attached to the backplate, the other ground wire should come from the junction box. If needed use a wire stripper to remove 3/8” of the insulation from each wire before inserting them into the corresponding wagon clip.
Step 7: Mount the canopy base (B) into the backplate using a Phillips head screwdriver to tighten mounting screws (C).
Step 8: Gently slide the canopy cover back up the stem (F). Rotate the canopy cover clockwise to secure it firmly in place.
Step 9: Gently remove the protective paper from the canopy cover on the stem (F). Discard.
Step 10: Carefully feed the shade (E) onto the end of each chandelier stem. Attach shade by threading clockwise. Repeat for all stems.
Step 11: Screw included bulbs (D) into place. Turn the power back on at the main fuse box or circuit panel you disabled before installation.
Assembly Guide. incommonwith.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>