CANOPIA 601760 Nancy 3 ft. x 5 ft. Door Awning Kit Instruction Manual

: June 12, 2024
: CANOPIA

Table of Contents

AVAILABLE SIZES
TOOLS & EQUIPMENT
SAFETY ADVICE
BEFORE ASSEMBLY
IMPORTANT!
DURING ASSEMBLY
CARE & MAINTENANCE
IMPORTANT ASSEMBLY STEPS
Contents
3 YEAR LIMITED WARRANTY
Declaration of Performance
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CANOPIA 601760 Nancy 3 ft. x 5 ft. Door Awning Kit

CANOPIA 601760 Nancy 3 ft. x 5 ft. Door Awning Kit

IMPORTANT!

Please read these instructions carefully before starting assembly. Keep these instructions in a safe place for future reference.

AVAILABLE SIZES

3×7 / 1×2

PRIMARY UNIT
3×7 / 1×2

|

1 BOX

3×14 / 1×4

AVAILABLE SIZES

PRIMARY UNIT
3×7 / 1×2

|

2 BOXES

CONNECTOR KIT
0.01 / 0.4

|

1 BOX

TOOLS & EQUIPMENT

2 people needed
Pencil
Work gloves
Electric Drill With Drill Bit 10mm | 13/32″
Spirit Level
Wrench 13 mm | 1/2″
Philips head Screwdriver
Ladder
Tape measure

HAVE A CONCERN? WE CAN HELP.
Before returning your purchase:

Please take a look at our “How to Assemble” video guide. Scan the QR Code below or go to canopia.shop/Assemble-Nancy

You didn’t find what you were looking for? We can help at canopia.shop/support

Still can’t find what you are looking for? Please see next page for local customer care.

INFORMATION

SAFETY ADVICE

It is of utmost importance to assemble all of the parts according to the directions. Do not skip any steps
We strongly recommend using work gloves during panel sliding .
Some parts may have sharp edges. Please be careful when handling components
Always wear shoes and safety goggles when working with extruded aluminium.
If using a step ladder or power tools make sure that you follow the manufacturer’s safety advice.
Keep children away from the assembly area.
Do not touch overhead power cables with the aluminium profiles
Do not attempt to assemble the product in windy or wet conditions .
Dispose of all plastic bags. Keep them out of reach of small children.
Do not climb or stand the roof
Do not hang or lay the profiles
Do not position your product in an area exposed to excessive winds .
Do not attempt to assemble this product if you are tired, have taken drugs or alcohol or if you are prone to dizzy spells
Make sure there are no hidden pipes or cables in the wall before inserting the pegs.
This product is designed to be used mainly as a Door Awning .
Heavy snow load on the roof can make it unsafe to stand below or nearby
The wall anchoring kit supplied with this product is suitable for concrete or solid brick walls. other wall types need an accordant wall fixation kit.

BEFORE ASSEMBLY

Selecting a site
- Choose your site carefully before beginning assembly
- Consider the door’s opening – inside or outside.
- The product must be positioned and fixed on a flat level surface
This is a multi-part assembly best achieved by two people Allow at least half a day for the assembly process.
Take all components & parts out of the packages. Sort the parts and check against the content parts list
Parts should be laid out close at hand. Keep all small parts (screws etc) in a bowl so they do not get lost
Please note multi-sided profiles are used in this Door Awning. As a result some holes in the profiles are not used during assembly
Please review entire instructions before starting. Carry out the assembly steps in exact order.
Please consult your local authorities if any permits are required prior to constructing the product.

IMPORTANT!

During assembly use a soft surface below the parts to avoid scratches and damages.
You are solely responsible for determining whether the handling, storage, assembly, installation or use of this product is safe and appropriate in any location or for any given application
The manufacturer is not responsible for any damages or injury to you, any other person or any property resulting from the improper handling, storage, installation, assembly or use of this product, or the failure to follow the manufacturer’s written instructions regarding the handling, storage, installation, assembly and use of this product
This product is intended for normal residential use only Do not use this product for any application that is not recommended in these instructions or building codes in effect in location where this product will be used. Always take care and use appropriate safety equipment (including eye protection) when assembling or installing this product
We recommend checking for restrictions or covenants for building this product in your area. In addition we advise to check if you need to submit any forms or if any permit is required prior to building the product.

DURING ASSEMBLY

During assembly, you will encounter different icons for different products . Please see below for more information:

|

You may use silicone lubricant spray on the frame in order to help you slide the panels into the profiles Do not spray the panels

---|---
|

Use a rubber mallet if necessary

|

Make sure you remove covering plastic film from both sides of the panel

|

All panels with the stamped words “THIS SIDE OUT’ must be facing out to create full UV protection. Remove plastic sticker as panels are locked in place

|

Steps marked with dashed outlines refer to Extensions only Some of the steps are irrelevant for an assembly of a single product When assembling a single or an extended product, some parts may be surplus

|

These 2 icons below indicate if screw’s tightening is required or not Temporary tightening of a few screws may be needed to prevent a profile from sliding out Tighten all screws once assembly is completed

CARE & MAINTENANCE

When your product needs to be cleaned, use a mild detergent solution and rinse with cold clean water .
DO NOT use acetone, abrasive cleaners or other special detergents to clean the panels
Clean the product once assembly is complete.

IMPORTANT ASSEMBLY STEPS

IMPORTANT ASSEMBLY STEPS

When encountering this information icon during assembly, please refer the relevant assembly step for important additional comments.

Step 5:
Peel the film covering the panel. Be careful not to scratch the panel from this step onwards!

Assembly Instruction

3 YEAR LIMITED WARRANTY

PALRAM – CANOPIA I 3 YEAR LIMITED WARRANTY
Palram Canopia Ltd. (Company number 512106824) whose registered office is at Teradion Industrial Park, M P Misgav 2017400, Israel (“Canopia”) warrants that the product will be free from defects in material or workmanship for a period of 3 years from the original date of purchase

This warranty is valid only if the product is installed, handled, cleaned, and maintained in accordance with Canopia’s written specifications
This warranty does not cover defects resulting from normal wear and tear including, but not limited to damage caused by use of force, incorrect handling, inappropriate use, negligence, accidents, impact from foreign objects, vandalism, pollutants, alteration, painting, damage resulting from cleaning with incompatible detergents or minor deviations of the product
This warranty does not apply to damage resulting from “acts of Nature”, which includes but is not limited to hail, storm, tornado, hurricane, blizzard, flood, or fire
Upon submitting proof of purchase and evidence of the claimed product failure, and subject to reporting the failure in writing within 30 days after discovery of the defect, Canopia, at its sole discretion, will replace defective parts of the Product, or refund you a prorated portion of the purchase price on a straight-line depreciated basis for the length of the warranty.

Declaration of Performance

According to Construction Products Council Directive UE N°305/2011 and EN 14963:2006 Issue Date 01/01/2022

Identification code: Nancy™ / Louisa™, refer to CE label no 004
Type: A light transmitting wall-supported 4 mm thickness solid PMMA extruded sheets structure made of aluminum and galvanized steel elements
Intended use: open multi-purpose covering
Manufacturer: Palram Canopia Ltd. Teradion Industrial Park, M.P Misgav 2017400, P.O.B. 53, Israel
Importer and EU representative: PALRAM Applications UK, Unit 40 J3 Industrial Estate Carr Hill,
Doncaster DN4 8DE
Assessment and verification of constancy of performance: System 3
Declared performance:

Resistances to upward load:UL1200
Resistance to downward loads: DL 1200

Reaction to fire: B, s1, d0
For mounting and fixing provisions see EN 16153:2013

Resistance to fire: NPD

External fire performance proof

Water tightness:
For the roof light with upstand: Pass
For the sheet material: Pass

Impact resistance:
For the small hard body: Pass
For the large soft body: NPD

Thermal transmittance:
For the roof light: NPD (not relevant to an open multi purpose cover)
For the sheet material: 5.86 W /( m2•K)

Direct air bome sound insulation: NPD(not revelent to an open multi purpose cover

Radiation transmittance:
– Light transmittance: Tv – 93.0 %
– Solar direct transmittance: Te – 81.83 %
– Solar factor: g value – 0.85

Air permeability:
For the roof light: NPD (not relevant to an open multi purpose cover)
For the sheet material: Pass

Durability ( of the sheet material): t,A, Cu 1, Ku 0

The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 7.
This declaration of performance is issued, in accordance with Annex ZA.2.2 – EN 14963:2006, under the sole responsibility of Pal ram Canopia Ltd.
ITT reports and Factory Production Control records are available upon request at www.canopia.com

Signed for and behalf of Pal ram Canopia Ltd. by:
Teradion Industrial Park, Misgav 01/01/2022

Customer Support

WE ARE HERE TO HELP
For general questions: canopia.com/contact-us

NORWAY • SWEDEN • ARGENTINA • GREECE • GREENLAND • ICELAND • ESTONIA • JAPAN • LATVIA • LITHUANIA MAURITIUS • MEXICO • ROMANIA • RUSSIA • TURKEY • UZBEKISTAN • UKRAINE • SWAZILAND • KOREA

Palram Canopia Ltd.
Teradion Industrial Park, M.P Misgav 2017400, P.O.B 53, Israel
Tel +972.4.848.6900 I Fax +972.4.848.6901
canopia@palram.com
www.canopia.com