ETHAN ALLEN 093037 Fiona Carved Wood Chandelier Instruction Manual
- June 12, 2024
- ETHAN ALLEN
Table of Contents
ETHAN ALLEN 093037 Fiona Carved Wood Chandelier Instruction Manual
IMPORTANT SAFETY INSTRUCTIONS. READ THESE INSTRUCTIONS COMPLETELY BEFORE
STARTING.
We strongly recommend that all direct-wired lighting products be installed by
a licensed electrician.
Two people may be required for installation. DO NOT EXCEED the rated bulb
wattage. Keep flammable materials away from bulb. This light fixture is
shipped with all internal wiring intact. Do not open the product or alter the
wiring in any manner.
Installation requires an electrical junction box in the ceiling sufficient to
support the weight of the light fixture.
This fixture weighs 13.2 lbs./(5.9 kg).
WARNING: Be certain that the power to the electrical junction box is turned off at the circuit breaker before installation. Turning the power off at a light switch is not sufficient to prevent electrical shock.
CAUTION: Prior to installation, locate ALL INCLUDED PARTS before disposing of packaging materials.
TOOLS REQUIRED FOR INSTALLATION:
- Screwdriver
- Electrical Tape
- Wire Cutters
- Pliers
- Adjustable Wrench
Note: Light bulb(s) are not included, except where required by State of California Title 20. See light fixture for bulb specification. Additional wiring supplies may be required.
Parts Included (refer to figure):
Part| Qty.| Description
A| 3| Wire Connectors
B| 1| Hot Fixture Wire
C| 2| Neutral Fixture Wire
D| 1| Mounting Screws
E| 1| Canopy
F| 1| Ground Wire
G| 2| Mounting Bracket
H| 1| Ground Screw
I| 2| Hex Nut
J| 1| Nipple
K| 1| Lock Washer
L| 1| Screw Collar Loop
M| 1| Threaded Ring
N| 1| Chain
O| 1| Fixture Loop
P| 1| Fixture Body
Installation Procedure (refer to figure)
A. Prep the fixture.
- SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER.
- Remove all parts from carton. Do not throw away any parts.
- Determine the desired distance between the base of the light fixture and your ceiling. Be sure to reserve extra cord length for the Ceiling junction box wire connections as noted in part B below.
- Adjust the power cord of the fixture from the Canopy (E).
- The Chain (N) length may be shortened from the top end by using pliers to remove chain links. Use a cloth or a folded piece of paper between the pliers and each link to protect the finish on the link during this process.
a. To remove a link, use two pairs of pliers to create an opening at the link’s split line.
b. To remove a length of chain, select the top link and remove it with the connected links intact.
B. Trim the power cord.
-
When the Chain (N) is at the desired length, open up the top link and attach it to the Screw Collar Loop (L). Re-weave the fixture’s two-wire cord cable and bare ground wire through every other link in the Chain (N); then through the Screw Collar Loop (L), the Nipple (J), and the Canopy (E); and then into the Mounting Bracket (G).
-
If needed (depending upon final fixture distance from the ceiling), cut off the extra length on the twowire cord cable and bare ground wire.
a. When cutting the power cord and bare ground wire, be sure to cut it so that it is at least 6″ (153 mm) long inside the ceiling junction box.
b. To prepare the cut power cord for the installation process, use wire strippers to prepare the ends of the two wires so there is about 1/2″ (13 mm) of exposed wire for the Wire Connectors (A). -
Gently pull existing Ground, Hot, and Neutral Junction Box Wires down from the ceiling junction box and allow these to hang.
C. Hard-wire the fixture.
-
Carefully inspect the chandelier’s fixture wires.
a. The Neutral Fixture Wire (C) is ribbed.
b. The Hot Fixture Wire (B) is smooth.
c. The Ground Wire (F) is a copper wire. -
Make proper electrical connections as described in steps 3–6. A LICENSED ELECTRICIAN IS RECOMMENDED.
-
Attach the Ground Wire (F) from the fixture to the Ground Junction Box Wire; it usually has green insulation around it or is bare wire. Fasten these together with a Wire Connector (A) and wrap the connection with electrical tape. Make sure no wire strands are exposed.
If your ceiling junction box does not have a ground junction box wire:
a. Insert the Ground Screw (H) into the Mounting Bracket (G) where it’s marked “Ground” and wrap the fixture’s bare ground wire around the Ground Screw (H).
b. Tighten the screw to clamp the ground junction box wire between the Ground Screw (H) head and the Mounting Bracket (G).
IT IS IMPERATIVE THAT THE CEILING JUNCTION BOX IN YOUR HOME BE PROPERLY GROUNDED. -
Connect the Neutral Fixture Wire (C) to the Neutral Junction Box Wire; it usually has white insulation around it. Fasten these together with a plastic Wire Connector (A) and wrap the connection with electrical tape. Make sure no wire strands are exposed.
-
Connect the Hot Fixture Wire (B) to hot junction box wire; it usually has black insulation around it. Fasten these together with a plastic Wire Connector (A) and wrap the connection with electrical tape. Make sure that no wire strands are exposed. Do not reverse the hot and neutral connections or safety will be compromised.
-
Gently tuck the wire connections neatly into the ceiling junction box.
D. Connect the fixture to the ceiling junction box and insert bulbs.
-
Attach the Mounting Bracket (G) to the ceiling junction box using the Mounting Screws (D). Tighten\ screws with a screwdriver until secure.
-
Attach one Hex Nut (I) to the top, and the other Hex Nut (I) to the bottom of the Nipple (J).
-
Put the Lock Washer (K) in before attaching the Screw Collar Loop (L) to the bottom end of the Nipple (J).
-
Secure the top of Nipple (J) to the Mounting Bracket (G) with the Hex Nut (I), exposing approximately 2″ of its thread.
-
Secure the Screw Collar Loop (L) to the bottom end of the Nipple (J) with the Hex Nuts (I) and Lock Washer (K).
-
Slide the Canopy (E) and the Threaded Ring (M) up the Chain (N).
-
Place the Canopy (E) over the ceiling junction box and secure it in place by screwing the Threaded Ring (M) onto the Screw Collar Loop (L).
-
Insert five (5) bulbs (not included) into the sockets. Do not exceed the specified wattage. Use any of the following:
a. 40W maximum Type B candelabra-base incandescent light bulbs
b. 8W maximum compact fluorescent light bulbs
c. 4W maximum LED light bulbs -
Restore power to ceiling junction box and test the fixture.
Care and Cleaning
- To clean, wipe with a soft, dry cloth.
- AVOID cleaners, scouring pads, etc.
After troubleshooting, if the lighting fixture still does not work, contact
your local Ethan Allen Design Center.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS. READ THESE INSTRUCTIONS COMPLETELY BEFORE
STARTING.
We strongly recommend that all direct-wired lighting products be installed by
a licensed electrician. Two people may be required for installation. DO NOT
EXCEED the rated bulb wattage. Keep flammable materials away from bulb. This
light fixture is shipped with all internal wiring intact. Do not open the
product or alter the wiring in any manner.
Installation requires an electrical junction box in the ceiling sufficient to
support the weight of the light fixture.
This fixture weighs 16.5 lbs./(7.4 kg)
WARNING: Be certain that the power to the electrical junction box is turned off at the circuit breaker before installation. Turning the power off at a light switch is not sufficient to prevent electrical shock.
CAUTION: Prior to installation, locate ALL INCLUDED PARTS before disposing of packaging materials.
TOOLS REQUIRED FOR INSTALLATION
- Screwdriver
- Electrical Tape
- Wire Cutters
- Pliers
- Adjustable Wrench
Note: Light bulb(s) are not included, except where required by State of California Title 20. See light fixture for bulb specification. Additional wiring supplies may be required.
Parts Included (refer to figure):
Part| Qty.| Description
A| 3| Wire Connectors
B| 1| Hot Fixture Wire
C| 2| Neutral Fixture Wire
D| 1| Mounting Screws
E| 1| Canopy
F| 1| Ground Wire
G| 2| Mounting Bracket
H| 1| Ground Screw
I| 2| Hex Nut
J| 1| Nipple
K| 1| Lock Washer
L| 1| Screw Collar Loop
M| 1| Threaded Ring
N| 1| Chain
O| 1| Fixture Loop
P| 1| Fixture Body
Installation Procedure (refer to figure)
A. Prep the fixture.
- SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER.
- Remove all parts from carton. Do not throw away any parts.
- Determine the desired distance between the base of the light fixture and your ceiling. Be sure to reserve extra cord length for the Ceiling junction box wire connections as noted in part B below.
- Adjust the power cord of the fixture from the Canopy (E).
- The Chain (N) length may be shortened from the top end by using pliers to remove chain links. Use a cloth or a folded piece of paper between the pliers and each link to protect the finish on the link during this process.
a. To remove a link, use two pairs of pliers to create an opening at the link’s split line.
b. To remove a length of chain, select the top link and remove it with the connected links intact.
B. Trim the power cord.
-
When the Chain (N) is at the desired length, open up the top link and attach it to the Screw Collar Loop (L). Re-weave the fixture’s two-wire cord cable and bare ground wire through every other link in the Chain (N); then through the Screw Collar Loop (L), the Nipple (J), and the Canopy (E); and then into the Mounting Bracket (G).
-
If needed (depending upon final fixture distance from the ceiling), cut off the extra length on the twowire cord cable and bare ground wire.
a. When cutting the power cord and bare ground wire, be sure to cut it so that it is at least 6″ (153 mm) long inside the ceiling junction box.
b. To prepare the cut power cord for the installation process, use wire strippers to prepare the ends of the two wires so there is about 1/2″ (13 mm) of exposed wire for the Wire Connectors (A). -
Gently pull existing Ground, Hot, and Neutral Junction Box Wires down from the ceiling junction box and allow these to hang.
C. Hard-wire the fixture.
-
Carefully inspect the chandelier’s fixture wires.
a. The Neutral Fixture Wire (C) is ribbed.
b. The Hot Fixture Wire (B) is smooth.
c. The Ground Wire (F) is a copper wire. -
Make proper electrical connections as described in steps 3–6. A LICENSED ELECTRICIAN IS RECOMMENDED.
-
Attach the Ground Wire (F) from the fixture to the Ground Junction Box Wire; it usually has green insulation around it or is bare wire. Fasten these together with a Wire Connector (A) and wrap the connection with electrical tape. Make sure no wire strands are exposed.
If your ceiling junction box does not have a ground junction box wire:
a. Insert the Ground Screw (H) into the Mounting Bracket (G) where it’s marked “Ground” and wrap the fixture’s bare ground wire around the Ground Screw (H).
b. Tighten the screw to clamp the ground junction box wire between the Ground Screw (H) head and the Mounting Bracket (G).
IT IS IMPERATIVE THAT THE CEILING JUNCTION BOX IN YOUR HOME BE PROPERLY GROUNDED -
Connect the Neutral Fixture Wire (C) to the Neutral Junction Box Wire; it usually has white insulation around it. Fasten these together with a plastic Wire Connector (A) and wrap the connection with electrical tape. Make sure no wire strands are exposed.
-
Connect the Hot Fixture Wire (B) to hot junction box wire; it usually has black insulation around it. Fasten these together with a plastic Wire Connector (A) and wrap the connection with electrical tape. Make sure that no wire strands are exposed. Do not reverse the hot and neutral connections or safety will be compromised.
-
Gently tuck the wire connections neatly into the ceiling junction box.
D. Connect the fixture to the ceiling junction box and insert bulbs.
-
Attach the Mounting Bracket (G) to the ceiling junction box using the Mounting Screws (D). Tighten screws with a screwdriver until secure.
-
Attach one Hex Nut (I) to the top, and the other Hex Nut (I) to the bottom of the Nipple (J).
-
Put the Lock Washer (K) in before attaching the Screw Collar Loop (L) to the bottom end of the Nipple (J).
-
Secure the top of Nipple (J) to the Mounting Bracket (G) with the Hex Nut (I), exposing approximately 2″ of its thread.
-
Secure the Screw Collar Loop (L) to the bottom end of the Nipple (J) with the Hex Nuts (I) and Lock Washer (K).
-
Slide the Canopy (E) and the Threaded Ring (M) up the Chain (N).
-
Place the Canopy (E) over the ceiling junction box and secure it in place by screwing the Threaded Ring (M) onto the Screw Collar Loop (L).
-
Insert five (5) bulbs (not included) into the sockets. Do not exceed the specified wattage. Use any of the following:
a. 40W maximum Type B candelabra-base incandescent light bulbs
b. 8W maximum compact fluorescent light bulbs
c. 4W maximum LED light bulbs -
Restore power to ceiling junction box and test the fixture.
Care and Cleaning
- To clean, wipe with a soft, dry cloth.
- AVOID cleaners, scouring pads, etc.
After troubleshooting, if the lighting fixture still does not work, contact
your local Ethan Allen Design Center.
SAVE THESE INSTRUCTIONS
Documents / Resources
|
ETHAN ALLEN 093037 Fiona Carved Wood
Chandelier
[pdf] Instruction Manual
093036, 093037, 093037 Fiona Carved Wood Chandelier, 093037, Fiona Carved Wood
Chandelier, Carved Wood Chandelier, Wood Chandelier, Chandelier
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>