DALEN X30s 4K Projector With WiFi 5 and Bluetooth Instruction Manual
- May 15, 2024
- DALEN
Table of Contents
- X30s 4K Projector With WiFi 5 and Bluetooth
- Installation Preparation
- Remote Controls and Features
- Projection Distance
- Ceiling Mounting Steps
- Initial Setting
- How To Use Light
- About the Monitor
- Shutdown Options
- Wireless Projection
- How to Disassemble
- Description of Various Situations
- System Upgrade
- Basic parameters
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
30s 4K Projector With WiFi 5 and Bluetooth
Instruction Manual
Magic Lamp Projector
Quick Installation Instruction Manual
Model: X30S
X30s 4K Projector With WiFi 5 and Bluetooth
Be sure to read the safety manual carefully before using the product. Please read the installation manual carefully, use the product correctly, and keep this manual carefully.
Installation Preparation
Please check all accessories before installation.
Confirmation of accessories before unpacking
- Magic Lamp Projector
- lampshade, decorative cover
- ceiling mount bracket
- remote control
- remote control battery(2 AAA batteries)
- screw pack
Remote Control Preparation
- Push the battery door of the remote control with your fingers, and pull up the tail to open the battery door.
- Install 2 AAA batteries, cover the battery door, push it up to close.
Remote Controls and Features
Projection Distance
Recommended projection distances for the screen size 
Reserve appropriate distance, 100 inch screen easy to cast
X30S/X3OH Test Parameters (Recommended screen aspect ratio 16:9)
Screen Size| Screen Length (cm)| Screen Width (cm)| Lens to
screen distance(cm)| center point (cm)
60 Inch| 133| 75| 101| 124
70 Inch| 155| 87| 117| 140
80 Inch| 178| 100| 136| 159
90 Inch| 200| 112| 152| 175
100 Inch| 221| 125| 171| 194
110 Inch| 245| 137| 187| 210
120 Inch| 266| 149| 204| 227
150 Inch| 332| 187| 257| 280
- The above parameters are based on the default data confirmed by the factory, and the wall surface is 2.8 meters. There may be slight deviation due to manual measurement.
Ceiling Mounting Steps
Turn off the light’s power switch (or turn off the circuit breaker) 
Remove magic lamp projector from the packaging
-
Unscrew the lampshade counterclockwise.
-
Unscrew the decorative cover counterclockwise.
-
Hold the host with both hands, and the plug of the fixing bracket passes through the round hole in the middle of the host.
-
Lift the host up until the sound of buckling is heard.
-
Push the control lever of the fixed bracket to LOCK to lock it.
-
Confirm whether the installation of the main engine maintains a level balance.
Connect the plug of the fixing bracket to the socket inside the host
After the plug is connected, please do not turn the host at a large angle.
(Junction box may come off)
If you want to rotate and adjust the direction at a large angle, please unplug
it before making adjustments. 
The position of the glass cover (projection window) is adjusted o face the
direction of the wall Installed.
Turn the light switch on (or turn the circuit breaker on)
Initial Setting
After startup, “Now Loading…” will be projected. After the system is loaded, please refer to the instructions of the sound and the projected screen, as follows.
-
Remote Controller Pairing Please point the remote control at the magic lamp projector, within 50cm from the host.
Press and hold the Home button and the Back button on the remote at the same time.
At this time, the status indicator light above the remote control will flash, and wait for the projection lamp to emit light. After the “ding” sound, the pairing is complete. -
Focus Sharpness Adjustment Press the Focus button , the focus screen will pop up, at this time, press the Left and Right buttons of the arrow key to adjust the picture to a clear state.
-
Image Position Adjustment Press the Focus button , the focus screen will pop up, press the Up and Down buttons of the arrow key to adjust the top and bottom positions of the image.
-
Image Keystone Correction Enter the keystone correction of the setting item
Use the arrow key * to select the four corners of the image, click the OK button to select the corresponding corner, and adjust the balance with the up, down, left, and right keys , and click the OK
– button to end the setting of the angle. Adjust the four corners by analogy. Press the down key of the direction key, click OK to enter the next step. -
Connect Network
According to the network detected on the screen, press the up and down keys of the direction keys to select the network, and click the OK – button to confirm. If the following screen appears, please enter the network password. -
Automatic Upgrade For a better product experience, the system will automatically upgrade upon initial startup when connected to the internet. The upgrade process will take approximately 5 to 10 minutes. Please do not turn off the power during the upgrade. Once the upgrade is successful, you can use the system normally.
Simple Process: Power on – Connect to WiFi – System upgrade -
Aladdin Mode Learn how DALEN Aladdin is used.
Press the OK key to enter the next screen, when the following screen finally appears, the initial setting is completed.
How To Use Light
How to use light
Turn on / off light
Operate with Remote Control
To use the remote control to operate, please turn on the power switch of the
lamp. 
Dimming color
Operate with Remote Control
Warm white light will appear after pressing the switch button of the light.
(You can customize the light color in the settings)
The order is whole light – watching movies – learning – full warm .
After pressing the brightness adjustment button of the light, the current
brightness of the light will increase, increase to the brightest and retum to
the lowest belches, so as to circle.
The color temperature of light can be customized in “System Setting” and “Lighting Setting” on the home screen.
Lighting Setting You can choose the brightness and adjust it in “Setting” and
“Lighting Setting” on the home screen.
Adjust brightness and color temperature and save.
Save in the setting, the light color that has been set will be retained.
About the Monitor
Home Screen
Click the arrow keys on the remote control to select content
The app can be used after pressing the OK button .
– Click the home button on the remote
control to return to the home page.
– If you need to adjust the volume, you can use the volume keys on the remote
control to control. the volume.
Shutdown Options
Power OFF
Operate with Remote Control 
Wireless Projection
Casting operation
How to Disassemble
Turn off the lights power (or turn off circuit breakers).
- Remove the outer lampshade, turn counterclockwise to remove the lampshade.
- Remove the decorative cover.
Unplug the junction box plug
from the internal socket of the main unit.
Take the host off the fixed bracket.
- Support the main unit with one hand, and hold the balance support handle with the other hand.
- While holding the support handle, push the control lever of the junction box to OPEN to unlock.
- Carefully support the main unit and remove it downwards.
Remove the fixing bracket from the ceiling.
Loosen the 4 screws one by one, and remove the fixing bracket.
Description of Various Situations
Situation
Can’t operate the remote
| Reason | Countermeasures |
|---|---|
| The light switch on the wall is off, so the remote cannot be operated. | Please |
turn on the light switch on the wall and operate it with the remote control
again.
There is a shield between the remote control and the host.| Remove the shield,
and operate the remote controller close to the host.
The Bluetooth of the remote control and
the main unit are not connected.| (1) Place the remote control within 50cm
from the main unit, and press and hold the home and retum buttons at the same
time
(2) Wait until the status indicator light on the remote control blinks and
then release the button
When you hear a “ding” sound, the pairing is successful
If you still can’t tum on the projection after pressing here, just press the
status light on the main unit (Red light in standby mode, green light when
power on)
The remote control batteries are not inserted correctly| Please make sure the
battery is installed in the correct direction.
Remote control battery is dead| Please replace the battery with a new one.
Reset
Reset
- Enter the setting App through the remote control.
- Enter the “Other” option.
- Select to enter “Restore Factory Settings”, after the countdown is over, select “OK” to restore the factory settings.
System Upgrade
Online Upgrade
System Upgrade
- Enter the online upgrade app through the remote control.
- Click “Check for Update”.
- Select “Online Upgrade” to complete the system upgrade.
Basic parameters
Magic Lamp Projector
Product Model : X30S
Projector Input : 100- 240V~, 50/60Hz 1A
Projector Power : 62W
Lamp Power : 38W (80x1W/LED module+72×0.2W/LED module)
Projector Type: LED Tungsten-halogen Discharge
Executive standard: EN 60598-1;EN 60598-2-1; EN 62368-1; UL 1598; CSA
C22.2#250.13; UL 62368-1; CSA C22.2#62368-1;
-
Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Manufactured under license from Dolby Laboratories.
Warning- In order to ensure the stability of the power supply of the machine, please use a power supply line that meets the national electricity standard.
- Please use the power type indicated on the product for power supply.
- Do not disassemble the machine by yourself, otherwise you will not be able to enjoy the warranty service provided by the company.
- This product does not have waterproof function, in order to pre-vent electric shock, please avoid water shower or water splash.
- If you will not use it for a long time, please turn off the power of the machine or turn off the power switch.
- When shipping the product, please use the original packaging shockproof material of the machine.
- If you find that the product is damaged, please contact customer service in time, do not repair it by yourself.
- Dry locations only.
- Installation for this product can only be operated by professionals. The light source of this product can only be changed by manufacturer or its service agent or other qualified workers.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2)this device must accept any interference received, including interference
that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
requency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Magic Lamp Projector
Brand/Manufacturer:
Jiangsu Dalen Electronics Co., Ltd.
Website: www.dalen-tech.com
E – mail: overseas@dalen-tech.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>