DALEN X30S Magic Lamp Projector User Guide

**DALEN X30S Magic Lamp Projector User Guide

**

Be sure to read the safety manual carefully before using the product.
Please read the installation manual carefully, use the product correctly, and keep this manual carefully.

Installation Preparation

Confirmation of accessories before unpacking

• Magic Lamp Projector
• lampshade, decorative cover
• ceiling mount bracket
• remote control
• remote control battery(2 AAA batteries)
• screw pack

Please check all accessories before installation.

Remote Control Preparation

1. Push the battery door of the remote control with your fingers, and pull up the tail to open the battery door.

2. Install 2 AAA batteries, cover the battery door, push it up to close.

Remote Controls and Features

Projection Distance

Recommended projection distances for the screen size

X30S/X30H Test Parameters (Recommended screen aspect ratio 16:9)

Screen Size| Screen Length
(cm)| Screen Width
(cm)| Lens to screen distance (cm)| center point (cm)
60 Inch| 133| 75| 101| 124
70 Inch| 155| 87| 117| 140
80 Inch| 178| 100| 136| 159
90 Inch| 200| 112| 152| 175
100 Inch| 221| 125| 171| 194
110 Inch| 245| 137| 187| 210
120 Inch| 266| 149| 204| 227
150 Inch| 332| 187| 257| 280

The above parameters are based on the default data confirmed by the factory, and the wall surface is 2.8 meters. There may be slight deviation due to manual measurement.

Ceiling Mounting Steps

Initial Setting

After startup, “Now Loading…” will be projected. After the system is loaded, please refer to the instructions of the sound and the projected screen, as follows.

1. Remote Controller Pairing

Please point the remote control at the magic lamp projector, within 50cm from the host.
Press and hold the Home button and the Back button on the remote at the same time.
A0 At this time, the status indicator light above the remote control will flash, and wait for the projection lamp to emit light. After the “ding” sound, the pairing is complete.

2. Focus Sharpness Adjustment

Press the Focus button , the focus screen will pop up, at this time, press the Left and Right buttons of the arrow key to adjust the picture to a clear state.

3. Image Position Adjustment

Press the Focus button , the focus screen will pop up, press the Up and Down buttons
of the arrow key to adjust the top and bottom positions of the image.

4. Image Keystone Correction

Enter the keystone correction of the setting item
Use the arrow key to select the four corners of the image, click the OK button to select the corresponding corner, and adjust the balance with the up, down, left, and right keys ,and click the OK button to end the setting of the angle. Adjust the four corners by analogy. Press the down key of the direction key, click OK to enter the next step.

5. Connect Network
   

6. Aladdin Mode

Learn how DALEN Aladdin is used.
Press the OK key to enter the next screen, when the following
screen finally appears, the initial setting is completed.

How To Use Light

How to use light
Turn on / off light 

Operate with Remote Control

To use the remote control to operate, please turn on the power switch of the lamp.

Dimming color

Operate with Remote Control

The color temperature of light can be customized in “System Setting” and “Lighting Setting” on the home screen.

Lighting Setting

Save in the setting, the light color that has been set will be retained.

About the Monitor

Home Screen

Click the arrow keys : – on the remote control to select content
The app can be used after pressing the OK button .

• Click the home button & on the remote control to return to the home page.
• If you need to adjust the volume, you can use the volume keys on the remote control to control. the volume.

Shutdown Options

Power OFF

Operate with Remote Control

Wireless Projection

Casting operation

How to Disassemble

1. Turn off the lights power (or turn off circuit breakers).

2. 1. Remove the outer lampshade, turn counterclockwise to remove the lampshade.

3. Remove the decorative cover.

4. Unplug the junction box plug from the internal socket of the main unit.
   

5. Take the host off the fixed bracket.
   

6. Support the main unit with one hand, and hold the balance support handle with the other hand.

7. While holding the support handle, push the control lever of the junction box to OPEN to unlock.

8. Carefully support the main unit and remove it downwards.

9. Remove the fixing bracket from the ceiling.
   Loosen the 4 screws one by one, and remove the fixing bracket.

Description of Various Situations

it with the remote control again.
There is a shield between the remote control and the host.| Remove the shield, and operate the remote controller close to the host.
The Bluetooth of the remote control and the main unit are not connected.
| (DPlace the remote control within 50cm from the main unit, and press and hold the home and return buttons at the same time. (@Wait until the status indicator light on the remote control blinks and then release the button. When you hear a “ding” sound, the pairing is successful. If you still can’t turn on the projection after pressing here, just press the status light on the mainunit.(Red light in standby mode, green light when power on)
The remote control batteries are not inserted correctly| Please make sure the battery is installed in the correct direction.
Remote control battery is dead.| Please replace the battery with a new one.

Reset

1. Enter the setting App through the remote control.
2. Enter the “Other” option.
3. Select to enter “Restore Factory Settings”, after the countdown is over, select “OK” to restore the factory settings.

System Upgrade

Online Upgrade

System Upgrade

1. Enter the online upgrade app through the remote control.
2. Click “Check for Update”.
3. Select “Online Upgrade” to complete the system upgrade.

Basic parameters

Magic Lamp Projector

Product Model: X30S
Projector Input: 100 – 240V~, 50/60Hz 1A
Projector Power: 62W
Lamp Power: 38W (80x1W/LED module+72×0.2W/LED module)
Projector Type: LED Tungsten-halogen Discharge
Executive standard: EN 60598-1;EN 60598-2-1; EN 62368-1; UL 1598; CSA C22.2#250.13;
UL 62368-1; CSA C22.2#62368-1;

Warning

• In order to ensure the stability of the power supply of the machine, please use a power supply line that meets the national electricity standard.
• Please use the power type indicated on the product for power supply.
• Do not disassemble the machine by yourself, otherwise you will not be able to enjoy the warrantyservice provided by the compa-ny.
• This product does not have waterproof function, in order to pre-vent electric shock, please avoid water shower or water splash.
• If you will not use it for a long time, please turn off the power of the machine or turn off the power switch.
• When shipping the product, please use the original packaging shockproof material of the machine.
• If you find that the product is damaged, please contact customer service in time, do not repair it by yourself.
• Dry locations only.

Brand/Manufacturer:
Jiangsu Dalen Electronics Co., Ltd.
Website: www.dalen – tech.com
E – mail: overseas@dalen – tech.com

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarant ee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environm ent. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>