ASSA ABLOY YRDC-2 Yale Smart Opener-Garage User Manual
- June 12, 2024
- ASSA ABLOY
Table of Contents
ASSA ABLOY YRDC-2 Yale Smart Opener-Garage
Product Information
- Product Name: Sahara Manual Yale Smart Opener-Garage / YRDC-2
- Description: Sahara is a dry contact device that is built with Wi-Fi and Bluetooth connections. It allows the Yale Access app to send an electric strike to a GDO (Garage door opener) or Gate automation device that it is connected to. The product also includes a wireless DPS (Door Position Sensor) that provides the user with the current state of the gate or garage door.
Product Usage Instructions
- Ensure safety first: Stay home if you have flu symptoms, keep your distance, wash/sanitize hands regularly.
- Assembly point and emergency exit should be identified and known.
- Keep emergency numbers accessible.
- Make sure you have a first aid kit readily available.
- Use protective equipment as necessary.
- To control access into the garage or through the gate, follow these steps:
- Download and install the Yale Access app on your smartphone.
- Connect the Sahara Manual device to your GDO or Gate automation device using Wi-Fi or Bluetooth.
- Open the Yale Access app and follow the instructions to pair and set up the Sahara Manual device.
- Once paired, you can use the app to send an electric strike to open or close the garage door or gate.
- The wireless DPS will indicate the door’s current state (open or closed).
Note: Any modifications or changes to the device that are not approved by the manufacturer may void your authority to operate the equipment under FCC rules. Please refer to the user manual for additional information and safety guidelines.
For more information, visit assaabloy.com
Safety first
SAFETY INSTRUCTION
- Sahara is a dry contact device that is built with Wi-Fi and Bluetooth connections that allow the Yale Access app to send an electric strike to a GDO (Garage door opener) or Gate automation device that is it connected to.
- As part of its offering, we have also included a wireless DPS that will provide the end user with the correct state of the gate/ garage door.
- Through the use of both devices, the end user can now control access into the garage or through their gate and also see what state the door is in.
Hardware installation.
-
Step one
The end user is asked to power down their Gate Automation device in order to avoid any electric interface and dangerous encounters. -
Step two
The end user should then take the wires coming out of the ‘NO’ (Normally open), ‘Com1’ ports, and power supply ( 5V/ 24V) of the Sahara and connect these to the relevant ports on a Gate Automation device. (As every automation device has its own port locations, this connection method will be shown to them through a wiring compatibility checker on the app and the website) -
Step three
Once installed, the end user is asked to power up their Gate Automation device if the LED light on the Sahara turns on then power is now available on the device. -
Step four
The end user will be asked to power the wireless DPS and then attach it to the gate door and take the magnet that comes with it and attach it to the pillar of the gate which will allow the app to know the state of the gate. -
Step Five
This is an optional step for end users. If they have a ‘request for exit’ switch inside their garage they can connect this to the rex1 or rex2 ports and so then they can continue to open and close their garage through the switch
Gate Application.
-
Step one.
Remove Sahara from the box. -
Step two
Download the Yale Access App. -
Step 3
Scan the QR code on the Sahara an wireless DPS device that will take you through the registration process of your device on the Yale Access app and add the device to WiFi. -
Step 4
Hardware installation should now take place. The End user will be taken through a step-by-step guide on the Yale access app on how to install their Sahara, wireless DPS and magnet on a generic Gate Automation device (See hardware installation part to the right) -
Step 5
End user asked to test whether the device works after Sahara hardware installation is done -
Step 6
Now end users can use Sahara to open or close their gate (See example below).
Hardware installation.
-
Step one
The end user asked to power down their Garage door opener in order to avoid any electric interface and dangerous encounters. -
Step two
The end user should connect the wires from the ‘NO’ (Normally open), ‘Com1’ ports, and power supply ( 5V/ 24V) of the Sahara and connect these to the relevant ports on a garage door opener. (As every automation device has its own port locations, this connection method will be shown to them through a wiring compatibility checker on the app and the website) -
Step three
Once installed, the end user is asked to power up their garage door opener and if the LED light on the Sahara turns on then power is now available on the device -
Step four
The end user will be asked to power the wireless DPS and then attach it to the inside of the garage door allowing the app to know the state of the garage -
Step five
This is an optional step for end users. If they have a ‘request for exit’ switch inside their garage they can connect this to the rex1 or rex2 ports and so then they can continue to open and close their garage through the switch
Garage Application.
-
Step one.
Remove Sahara from the box. -
Step two
Download the Yale Access App. -
Step 3
Scan the QR code on the Sahara and wireless DPS device that will take you through the registration process of your device on the Yale Access app and add the device to WiFi. -
Step 4
Hardware installation should now take place. The End user will be taken through a step-by-step guide on the Yale access app on how to install their Sahara on a generic garage door opener (See hardware installation part to the right) -
Step 5
End user asked to test whether the device works after Sahara hardware installation is done -
Step 6
Now end users can use Sahara to open or close their garage door. (See example below).
FCC-ISED Manual information
Attached is PDF with FCC and ISED Information to be added to the Manual.
FCC
- This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
- Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Modifications not expressly approved by the manufacturer could void your authority to operate the equipment under FCC rules.
ISED
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF Exposure Statement
FCC and IC RF Radiation Exposure Statement: This equipment complies with FCC
and IC RF radiation exposure limits set forth for uncontrolled environments.
This equipment should be installed and operated with a minimum distance of
20cm （may be adjusted according to actual calculation result）between the
radiator and your body. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>