BOCCI 21.7 Seven Pendant Light Instruction Manual

: June 4, 2024
: BOCCI

Table of Contents

Product Overview
Specification
DESCRIPTION
Assembly instruction
Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BOCCI 21.7 Seven Pendant Light Instruction Manual

Product Overview

32 (1.3”)
adjustable up to
3000 (10’) standard

adjustable up to
30500 (100’) custom

203 (8”)

Specification

PENDANTS: seven
MOUNTING: brushed nickel canopy 203mm (8”) in diameter x 32mm (1.3”) deep
LAMPING: 1.5w LED or 20w xenon
COAX: adjustable. 3000mm (10’) standard / up to 30500mm (100’) maximum
MATERIALS: porcelain, borosilicate glass, braided metal coaxial cable, electrical components, brushed nickel canopy
WEIGHT: approximately 4.1kg (9lb)
POWER SUPPLIES integral

DESCRIPTION

21.7 is a clustered configuration of seven 21 pendants hung from a round canopy. The pendants are designed to hang in a random configuration at times clustering and grouping together and others trailing off. The result is an ambient installation or field of light. The pendant drop lengths on this fixture are adjustable up to the specified maximum.

Inspired by the sporadic, discordant arrangement of barnacles on a rock surface, the 21 is fabricated from thin sheets of porcelain wrapped around a trumpet shaped borosilicate diffuser. Each diffuser houses a low voltage lamp.
A strong contrast is established between the organically distributed soft light passing through the white porcelain skin and the sharp, crisp light passing through the borosilicate glass diffuser.

NOTES

Purchase replacement lamps online at www.bocci.com/shop/bulbs
Unless otherwise noted when ordering, all chandeliers will be outfitted to be xenon compatible.
As an alternative to a built-in power supply, Bocci recommends mounting power supplies remotely in an easily accessible and hidden location for ease of long-term maintenance.

Assembly instruction

Very carefully uncoil the braided coaxial cable in a spool like manner. Insert your index fingers into opposite sides of the roll then rotate your fingers around each other to unroll the coaxial cable.
Use patience: allow the cable to uncoil completely to avoid kinks.
Determine the overall drop for the pendant fixture.
Thread the coaxial cables through the canopy, use a 2mm Allen key to loosen the setscrew in the canopy and gently feed the cable through until you have reached your desired drop length.
Use Allen key to tighten the setscrew to hold the strain relief and secure the coaxial cable at its new length.
Perform a gentle tug test to ensure it is secure .

DO NOT OVER TIGHTEN.
Note: The strain relief is a black plastic collar around the coaxial cable. There is a single slot opening on the side of the strain relief component. It is essential that this opening is oriented at 90 degrees to set screw chamber. There can be no contact between the set screw and the cable.
RISK OF ELECTRIC SHORT!
Xenon (110V) or LED: connect the black wire to black and white wire to white wire.
Xenon (230V): connect black wire to brown wire and white wire to blue wire
Connect the coaxial cable to the open slots in the terminal block on the 12V side of the power supplies Ensure that the braided outer wires are all connected to one 12V output wire and all inner insulated wires are connected to the other or a short will occur. Once all coaxial connections are made, lift the fixture into position and connect the line voltage to the open slot in the appropriate terminal block.
The client is responsible to ensure fasteners are attached to a robust structural substrate.
Tuck the power supply and wiring into the canopy. Line up the fastener holes or connect directly to structural ceiling surface using the fasteners provided.

Turn power to fixture on.
Bocci LED or xenon lamps are included. Ramping is power supply specific.
Plug the lamp into the socket.

Do not touch the lamp with your bare hands. Ensure power to lamp is working correctly.
Thread the coaxial cable through the shade, followed by the boro silicate diffuse, the cap, and fi nally close off the diffuser with the diffuser gasket.
Clean fingerprints from surfaces