HUNTER RX10K-12K Alignment Scissor Lifts Instruction Manual

Lift Rack Accessories
For Hunter wheel alignment lift racks

RX10K-12K Alignment Scissor Lifts

FIA streamlines the entire alignment process.
Communication links automate tasks once performed by the technician manually, eliminating time-consuming trips around the vehicle and to-and-from the console.

PATENTED
RX Scissor Lift console
  Raising the vehicle triggers the sensors to look for wheel targets
  Control PowerSlide® and Inflation Station settings on the lift console
  Store bar-code scanner and CodeLink tool near the vehicle to save steps

AlignLights turn on automatically at alignment height

PATENTED
WinAlign® console
  Centralized control of entire system
Communicate directly with lift to set tire pressure and automatically operate turnplates and slipplates
Guide the technician through the alignment process

Measurements are taken automatically once the fourth target is installed
PATENTED
PowerSlide® system
  Slipplates and turnplates automatically lock and unlock at appropriate times
  No more struggles with lock pins

Auto-locking turnplates and slipplates save trips around the vehicle
PATENTED
Inflation Station
Automatically inflate all four tires simultaneously
Record starting and final pressure
  Hose recoils to keep work area clear

Software tracks before and after tire pressures for the customer’s printout

PowerSlide™ system

The PowerSlide™ system secures and releases slipplates and turnplates with one touch. With the PowerSlide™ system, technicians no longer have to make multiple trips around the vehicle or struggle to remove and replace lock pins during an alignment.

PowerSlide™ Turnplates
See page 7 for PowerSlide™ turnplate options.

  Conveniently located on the lift console
  Locks and unlocks slipplates and turnplates with the touch of a button
  Automatically locks when lift is lowered*

TIP
PowerSlide™ saves time operating as a stand-alone system, but operates most efficiently when connected to an aligner through FIA.

PowerSlide™ upgrades
– PowerSlide™ turnplates not included.
– Kits include all parts needed for upgrade but no installation payment. Consult your service rep before quoting.

NEWER
RX10K/12K SCISSOR LIFTS| RX14K/RX16KF SCISSOR LIFT| NEWER
L45X FOUR-POST LIFTS
---|---|---
20-3527-1| 20-3528-1| 20-3069-1
Adds PowerSlide™  capability & FIA| Adds PowerSlide™  capability| Adds PowerSlide™  capability

Inflation Station system

The Inflation Station system inflates all four tires to a pre-selected pressure simultaneously – while you raise the lift or do other tasks! Saves steps and save time!

Integrated inflation hoses, located at each wheel position, retract when not in use to keep the work area clear.

  Set tire pressure at the lift console or at the aligner*
  Automatically inflate all four tires simultaneously
Record starting and final pressure*
Printouts show starting and final tire pressures.

TIP
Inflation Station saves time operating as a stand-alone system, but operates most efficiently when connected to an aligner through FIA.
Inflation Station upgrades
– PowerSlide™ turnplates not included.
– Kits include all parts needed for upgrade but no installation payment. Consult your service rep before quoting.

| RX10K/12K SCISSOR LIFTS| RX16 SCISSOR LIFT| NEWER
L45X FOUR-POST LIFTS
---|---|---|---
Lift has no FIA features| 20-3529-1| 20-3530-1| 20-3070-1

AlignLights

The AlignLights system provides a safe and efficieLED light source underneath the vehicle without additional electrical cords.
The lights automatically switch on when the lift is raised and off when the lift is lowered.
20-3438-1 – for RX_K models only 20-2993-1 – for L45x models
AlignLights is an ALI listed accessory for all lift models.

AlignLights is available for most Hunter alignment lifts as an installed option or can be retrofitted to most previously installed lifts.

Swing Air Jacks

Hunter Swing Air Jacks provide reliable, full-pneumatic operation.
Proven over decades of use, air-operated cylinders raise the vehicle from either the suspension or frame. Swing air jacks are engineered to handle a wide variety of vehicles and provide easy, low-maintenance service.

9,000-lb. Capacity,
Triple Composite Cylinder Jack 133-84-1
Ideal for use with RX16, L45x lift models.

6,000-lb. Capacity,
Dual Composite Cylinder Jack 133-85-1
Ideal for use with RX-10 and RX12A lift models.

Swing Air Jack clearances

Turnplates

PowerSlide™ Turnplates
PowerSlide™ turnplates eliminate the hassle of removing and replacing lock pins during an alignment. Integrated bridges lower and raise as plates are locked. PowerSlide™ turnplates are an optional feature that may be added later to qualified RX and Four-Post series lifts.

20-2076-1|  PowerSlide™  turnplates with automatic bridges| For use with camera-based alignment sensors
---|---|---

Stainless Steel Turnplates
Resists corrosion and maintains free movement during the alignment procedure. Stainless steel construction for long, trouble-free life. No pointer.

20-2532-1| Stainless Steel (set of 2)| Fits 1.5″ or 50 mm turnplate pockets Includes guide strips
---|---|---
20-2533-1| Stainless Steel, Low Friction set of 2)| Fits 50 mm turnplate pockets Includes guide strips

Painted Turnplates 20-2531-1BLK
Set of two turnplates for 1.5″ or 50 mm turnplate pockets. Steel construction with a powder-coated paint finish. No pointer.

Turnplate Bridge
Eases rolling compensation when rack is used with camera-based alignment sensors.
20-2307-1 Universal Bridge for 50 mm and 1.5″ turnplate pockets

Filler Plates
Fills turnplate pockets when turnplates are not used. 19.5″ wide.
20-2395-1BLK For 50 mm pockets (two included)

Ramps & extensions

High-floor-slope conditions and low-ground-clearance vehicles occasionally require additional approach ramp length.
Stage 2 RX Approach Ramp Extensions (only available in red or black)

20-3113-1| RX ramp extension kit (set of 2)| Adds 17.75″ to the length of RX10K, RX9, RX10, and RX16
Standard on RXDC, RX12K, and RX14K
---|---|---
20-2189-1| RX ramp extension (incl. quick-release pins| Adds 50″ to length of RX10K, RX9, RX10, and R X16
Adds 37.25″ to RX-12, RX12A, RX12K, and RX14K

Stage 2 Four-Post Ramp Extension Kit (only available in red or black)

20-3145-1| Four-Post ramp extension for 26-in. runways|  Adds 17.5″ to length of ramps
---|---|---
20-3146-1| Four-Post ramp extension for 26-in. runways|  Adds 40″ to the length of ramps

Refer to form 6652-T for ramp extension recommendations based on vehicle ground clearance.

Ramps & extensions cont.

Drive-Thru Kit – 20-2498-1
(Only available in red or black.)
RX10K, RX12K, and RX14K drive-thru kit for camera sensors Also suitable for legacy RX10, RX12A, and RX16 racks Adds 52″ to overall length

Flush-Mount Conversion Kit – 20-2736-1
Converts surface-mount installations to flush-mount installations, using current site requirements. (Only available in red or black.) For RX10K and RX12K
Also fits legacy RX10 and RX12A racks

Long Wheel Stops – 20-2497-1
For use with conventional sensors and vehicles with low spoilers.
(Only available in red or black.)
Fits current RX10K, RX12K, RX14K racks, as well as legacy RX10, RX12A, and RX16 racks
Adds approximately 12″ in length

Additional lift accessories

Pit Hose Reel Cover Plates (set of 4) 20-2267-1
Cover plate for Inflation Station lifts to trim around flush-mount cut-outs.
51-2308-1 Single pit hose reel cover plate

Center Lift Jack Adaptor
20-2854-1 (6,000 lb) 20-2853-1 (9,000 lb)
Ideal accessory for lifting from the differential or subframe on many vehicles. Includes storage bracket.
Suitable for 133-84-1 and 133-85-1 jacks only.

Front-Mount Power
Unit Bracket – 20-3072-1
For L45x models
Moves power unit mounting to front of four-post column for bays with very little space.

Work Step – 51-1696-1
Work step makes custom steer or underhood shim work easier. Can be used with RX, L45X, L42X, L44X, RM, PN and RMHD models.

Jack Riser Kit (set of 2) – 20-2801-1
Extends the reach of the jack to make lifting high- ground-clearance and long- wheelbase vehicles easier. Adds 4.5″ to overall jack lift height.
Suitable for 133-84-1 and 133-85-1 jacks only.

Additional lift accessories

Storage Bracket Kit 20-2528-1

Provides storage for wheel adaptors on console, lift or HawkEye Elite® sensor column. Simply bolts on to clip-on work step holes, no drilling required. Includes four brackets.

Wheel Chock – 22-525-2
Prevents vehicle from rolling once on the lift.
Two chocks are included standard in any new lift purchase.
Be sure to check out Hunter’s lift rack literature for more detailed information on each product.

Because of continuing technological advancements, specifications, models, and options are subject to change without notice.
WinAlign and HawkEye Elite are registered trademarks of Hunter Engineering Company.
0722CH
Copyright © 2022, Hunter Engineering Company

www.hunter.com
Form RB05262-00, 07/22
Supersedes Form RB05262-00, 08/21

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>