DEAF BONCE ML-10A Active Subwoofer Owner’s Manual

: June 12, 2024
: Deaf Bonce

Table of Contents

DEAF BONCE ML-10A Active Subwoofer
Product Information
Safety Instructions
ML-10A
ML-12A
INTRODUCTION
SAFETY INSTRUCTIONS
WIRING DIAGRAMS
Application of connectors and controls
HOW TO USE
SPECIFICATIONS
DIMENSIONS
BOX CONTENTS
WARRANTY AND MAINTENANCE INFO
Documents / Resources

DEAF BONCE ML-10A Active Subwoofer

DEAF-BONCE-ML-10A-Active-Subwoofer-product

Product Information

The Deaf Bonce ML-10A and ML-12A Active Subwoofers are designed to deliver extremely loud sound systems without compromising quality. These subwoofers are ideal for enhancing the low-frequency performance of your audio system.

Safety Instructions

Properly fasten the subwoofer during installation to prevent damage to the passengers or other vehicles in the event of disconnection while driving.
If possible, store the product in its original package before installation to avoid accidental damage.
Exercise caution when installing or dismantling the subwoofer to prevent damage to its moving parts.
High sound pressure can be harmful to your health. Use common sense when controlling the volume.

Wiring Diagrams

Refer to the following table to select the appropriate diameter of speaker cables based on the length and power consumption:

Power Consumption (W)	Cable Length (m)	Size
25,000	0-1	5
20,000	1-2	16.8
15,000	2-3	8.37
10,000	3-4	10
8,000	4-5	5.26
6,000	5-6	14
4,000	6-7	2.08
2,000	7-8	4
1,000		8.37
500		5.26
250		10
100		16.8

How to Use

To achieve optimal performance, follow these recommended settings:

The volume of the Head Unit (HU) should not exceed 80%.
The amplifier sensitivity should be set to 50%.
The low pass filter LPF should be set to a frequency range of 63-80 Hz. This filter cuts all frequencies above the set range.

Specifications

Model| Subwoofer Size (Inch)| Power RMS (Watt)| Power MAX (Watt)| Frequency Response (Hz)| Impedance (Ohm)
---|---|---|---|---|---
ML-10A| 10| 250| 1000| 25 – 280| 4
ML-12A| 12| 250| 1000| 25 – 280| 4

Dimensions

ML-10A

Width: 228.70 mm / 9″
Height: 330 mm / 12.99″
Depth: 330 mm / 12.99″

ML-12A

Width: 281.62 mm / 11.09″
Height: 355 mm / 13.98″
Depth: 355 mm / 13.98″

Box Contents

Active subwoofer – 1 pc.
Owner’s manual – 1 pc.
Warranty card – 1 pc.

Warranty and Maintenance Information

Deaf Bonce products are warranted against defects concerning materials and their manufacturing under normal functioning conditions.
If the product is under warranty, defective parts will be repaired or replaced at the manufacturer’s discretion. The defective product, along with a notification, must be returned to the dealer from which it was purchased, along with the filled-in warranty certificate and the original packaging. If the product is no longer under warranty, repair costs will apply.
The company does not assume any liability for damages during transportation or loss of profit due to the inability to use the product. For more information, please visit our website and carefully read the warranty card.

INTRODUCTION

Thank you for purchasing of this Deaf Bonce product! Our company is committed to the creation of extremely loud sound systems with no loss of quality.
To ensure proper use, please carefully read through this manual before using this product. It is especially important that you read and observe caution’s in this manual. Please keep the manual in a safe and accessible place for future reference.

SAFETY INSTRUCTIONS

Fasten the subwoofer properly when installing it in the vehicle. If the component is disconnected during driving, it may cause serious damage to the passengers of the vehicle or another vehicle.
Before installing the components, if possible store the product in its original package to avoid accidental damage to the product.
Be careful when installing or dismantling of the subwoofer! Do not let the subwoofer drop to avoid damage of its moving parts.
When working with tools follow safety rules.
Before the installation switch oﬀ the head unit and all other audio devices to avoid their damage.
Make sure that the location of the subwoofer does not hinder the proper operation of mechanical and electrical devices of the vehicle.
Do not install components in places exposed to water, excessive humidity, high or low temperature, dust or dirt.
ATTENTION!!! The product may be operated at +5 °C (41F) to +40 °C (104F). In case of moisture condensation, let the product to dry.
When performing plumbing, drilling or cutting works with the car, make sure that there is no wiring, brake lines, fuel pipe or other structural elements under the place of work. Follow the safety rules! Use protective glasses and gloves.
When stretching back the speaker cables make sure that they are not in contact with sharp edges or moving mechanical devices. Make sure that they are ﬁrmly ﬁxed and protected over the entire length.
The diameter of the speaker cables must be selected in accordance with the length and applied power.
Never stretch the cables outside of the car and near the moving parts of the car. This can lead to destruction of the insulating layer, short circuit and ﬁre.
To protect the cables use rubber gaskets if the wire passes through a hole in the plate, or other similar materials if it lies close to the parts exposed to heat.

CAUTION!!! High sound pressure can damage your health! Please use common sense when controlling the volume!

WIRING DIAGRAMS

Standard wiring diagram of an active subwoofer to battery and head unit

Step 1. Connect one end of the power cable from the (+) terminal of the battery and the second end to the amplifier terminal marked with +12V. Do not forget to protect the positive power cable with the appropriate fuse.
Step 2. Connect one end of the power cable from the (-) terminal of the battery and the second end of the grounding cable to the terminals marked with GND.
Step 3. Connect one end of the cable to the Remote output terminal at the HU and the second end to the amplifier terminal marked with REM IN.
Step 4. Connect one end of the RCA cable to the RCA output terminals at the HU and the second end to the amplifier RCA input terminals marked with INPUT.

Application of connectors and controls

FUSE – fuse connection terminal
+12V – power supply terminal +12 V
REM IN – the connector of remote activation of the amplifier
GND – grounding supply terminal
INPUT – signal input, RCA jacks
HIGH-LEVEL INPUT – high-level signal input terminal
REMOTE – input for connection of the bass remote control
GAIN – input signal level adjustment (0.85 – 4 V)
LPF – low pass filter (30 Hz – 280 Hz at 12 dB/Oct)
POWER – LED for operation (blue), LED for protection (RED)
GAIN – input signal level adjustment
POWER – LED for operation (blue)

Selection of the diameter of speaker cables

Use the table below to select the desired diameter based on the length and power consumption.

HOW TO USE

The correct choice of the ampliﬁer settings prolongs the lifetime of your subwoofer. Proper coordination of the head unit (HU) with the ampliﬁer will provide clean, undistorted signal fed to the subwoofer, which prevents overheating and voice coil damage. Like any other speaker the subwoofer has moving and stationary parts. We strongly recommend that the moving parts of the subwoofer should be warmed up at the beginning of operation. Be extra careful when warming up the parts. Warm up the subwoofer using musical material for 40 hours at medium power. If you feel strange smell during operation at maximum volume, you should lower the volume of the subwoofer and let the device to cool down at a low volume.
Recommended settings of the ampliﬁer and HU: Volume of HU should not exceed 80%. The ampliﬁer sensitivity should be set to 50%. The low pass ﬁlter LPF (the ﬁlter that cuts all frequencies above those set for the ﬁlter) should be set to 63-80 Hz.

SPECIFICATIONS

Model	ML-10A	ML-12A
Subwoofer size (Inch)	10	12
Power RMS (Watt)	250	250
Power MAX (Watt)	1000	1000
Frequency response (Hz)	25 – 280	25 – 280
Impedance (Ohm)	4	4

DIMENSIONS

DEAF-BONCE-ML-10A-Active-Subwoofer-
fig-4

BOX CONTENTS

Active subwoofer – 1 pc.
Owner’s manual – 1 pc.
Warranty card – 1 pc.

WARRANTY AND MAINTENANCE INFO

Deaf Bonce products are warranted against defects concerning materials and their manufacturing under normal functioning conditions.
While the product is under warranty, defective parts will be repaired or replaced at the manufacturer’s decision. The defective product, along with notiﬁcation about it, must be returned to the dealer from which it was purchased together with the warranty certiﬁcate duly ﬁlled in, complete with the original packaging. If the product is no longer under warranty, it will be repaired at the current cost.
Our company does not undertake any liability for damages due to transportation. Our company does not take any responsibility for costs or loss of proﬁt due to the impossibility to use the product, other accidental or consequential costs, expenses or damages suffered by the customer. Warranty according to laws in force. For more information visit our website and carefully read the warranty card.
The manufacturer reserves the right to change design and specification without prior notice.

INFORMATION ON DISPOSAL OF THE ELECTRICAL AND ELECTRONIC EQUIPMENT (FOR THE EUROPEAN COUNTRIES WITH SEPARATE WASTE COLLECTION)

Items marked “crisscrossed wheeled bin” are not allowed to be disposed of together with usual household waste. These electrical and electronic products should be disposed of in special reception centers, equipped for recycling such products and components.
For information about the location of the nearest disposal/recycling spot and the rules for the delivery of waste please contact your local municipal oﬃce. Recycling and proper disposal helps to protect the environment and prevent harmful eﬀects on health.
https://alphard.audio