DRAPER 65034 Storm Force Air Ratchet Instruction Manual

DRAPER 65034 Storm Force Air Ratchet

These instructions accompanying the product are the original instructions. This document is part of the product, keep it for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools policy of continuous improvement determines the right to make modifications without prior warning.

TITLE PAGE

INTRODUCTION:
USER MANUAL FOR: Air Ratchet Stock No: 65034
Part No’s: SFAR12

REVISIONS:
Date first published July 2019.
Revised version May 2022.

As our user manuals are continually updated, users should make sure that they use the very latest version.

Downloads are available from: http://drapertools.com/manuals

Draper Tools Limited Hursley Road Chandler’s Ford Eastleigh Hampshire
S0531YF
UK

Delta International BV Oude Graaf 8
6002 NL
Weert
Netherlands

Website: drapertools.com
Product Helpline: +44 (0) 23 8049 4344
General Fax: +44 (0) 23 8026 0784

UNDERSTANDING THIS MANUALS SAFETY CONTENT:
WARNING! Information that draws attention to the risk of injury or death. CAUTION! – Information that draws attention to the risk of damage to the product or surroundings.

COPYRIGHT© NOTICE:
Copyright© Draper Tools Limited.
Permission is granted to reproduce this publication for personal and educational use only. Commercial copying, redistribution, hiring or lending is prohibited.
No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited.
In all cases this copyright notice must remain intact.

WARRANTY

WARRANTY
Draper tools have been carefully tested and inspected before shipment and are guaranteed to be free from defective materials and workmanship.
Should the tool develop a fault, please return the complete tool to your nearest distributor or contact
Draper Tools Limited, Chandler’s Ford, Eastleigh, Hampshire, SO531YF. England.
Telephone Sales Desk: (023) 8049 4333 or Product Help Line (023) 8049 4344.
A proof of purchase must be provided with the tool.
If upon inspection it is found that the fault occurring is due to defective materials or workmanship, repairs will be carried out free of charge. This warranty period covering parts/labor is 6 months from the date of purchase except where tools are hired out when the warranty period is 90 days from the date of purchase. This warranty does not apply to any consumable parts, any type of battery or normal wear and tear, nor does it cover any damage caused by misuse, careless or unsafe handling, alterations, accidents, or repairs attempted or made by any personnel other than the authorized Draper warranty repair agent.

Note: If the tool is found not to be within the terms of warranty, repairs and carriage charges will be quoted and made accordingly.
This warranty applies in lieu of any other warranty expressed or implied and variations of its terms are not authorized.
Your Draper warranty is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the warranty period.
Please note that this warranty is an additional benefit and does not affect your statutory rights.

Draper Tools Limited.

INTRODUCTION

SCOPE
This air ratchet is designed for removal and installation of threaded fasteners.

SPECIFICATION

• Stock No. 65034
• Part No . ……………………………………………………………………………………………………………….. SFAR12
• Anvil size ½”
• Maximum torque ……………………………………………………………………………………………… 90Nm/66Ib-ft
• Max. operating air pressure 90psi (6.2bar)
• Average air consumption ……………………………………………………………………………… 5cfm (141 Umin)
• Revolution per minute (no load) 160r/min·1
• Minimum air line size …………………………………………………………………………………………………… %”ID
• Air inlet ¼” BSP
• Sound pressure level* …………………………………………………………………………………………….. 94dB(A)
• Sound power level** .105dB(A)
• Vibration level …………………………………………………………………………………………………………. 2.6m/s2
• Weight 1 .4kgs

Warning: Wear approved safety glasses and ear defenders.
*Continuous A-Weighted Sound Pressure Level at the workstation in accordance to prEN ISO 15744:1999.

A-Weighted Sound Power Level in accordance to prEN ISO 157 44:1999.

HEALTH AND SAFETY INFORMATION

GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE

• When using any type of power tool there are steps that should be taken to make sure that you, as the user, remain safe.

• Common sense and a respect for the tool will help reduce the risk of injury.

• Read the instruction manual fully. Do not attempt any operation until you have read and understood this manual.

• Most important you must know how to safely start and stop this machine, especially in an emergency.

• Keep the work area tidy and clean. Attempting to clear clutter from around the machine during use will reduce your concentration. Mess on the floor creates a trip hazard. Any liquid spilt on the floor could result in you slipping.

• Find a suitable location. If the machine is bench mounted; the location should provide good natural light or artificial lighting as a replacement. Avoid damp and dust locations as it will have a negative effect on the machine’s performance. If the machine is portable; do not expose the tool  to rain. In all cases do not operate power tools near any flammable materials.

• Keep bystanders away. Children, onlookers and passers by must be restricted from entering the work area for their own protection. The barrier must extend a suitable distance from the tool user.

• Disconnect and house all power tools that are not in use. An air tool should never be left unattended while connected to the power supply. They must be housed in a suitable location, away locked up and from children.
  Do not overload or misuse the tool. All tools are designed for a purpose and are limited to what they are capable of doing. Do not attempt to use a power tool (or adapt it in any way) for an application it is not designed for. Select a tool appropriate for the size of the job. Overloading a tool  will result in tool failure and user injury: This covers the use of accessories.

• Dress properly. Loose clothing, long hair and jewellery are all dangerous because they can become entangled in moving machinery: This can also result in parts of body being pulled into the machine. Clothing should be close fitted, with any long hair tired back and jewellery and neck ties  removed. Footwear must be fully enclosed and have a non-slip sole.

• Wear personal protective equipment (PPE). Dust, noise, vibration and swart can all be dangerous if not suitably protected against. If the work involving the power tool creates dust or fumes; wear a dust mask. Vibration to the hand, caused by operating some tools for longer periods must  be protected against. Wear vibration reducing gloves and allow long breaks between uses. Protect against dust and swarf by wearing approved safety goggles or a face shield. These are some of the more common hazards and preventions; however, always find out what hazards are  associated with the machine/work process and wear the most suitable protective equipment available.

• Do not breathe contaminated air. If the work creates dust or fumes; connect the machine (if possible) to an extraction system either locally or remotely. Working outdoors can also help if possible.

• Move the machine as instructed. If the machine is hand held, do not carry it by the air line. If the product is heavy; employ a second or third person to help move it safely or use a mechanical device. Always refer to the instructions for the correct method.

• Do not overreach. Extending your body too far can result in a loss of balance and you falling. This could be from a height or onto a machine and will result in injury.

• Maintain your tools correctly. A well maintained tool will do the job safely. Replace any damaged or missing parts immediately with original parts from the manufacturer. As applicable; keep blades; moving parts clean, oiled or greased; handles clean; and emergency devices working.

HEALTH AND SAFETY INFORMATION

• Wait for the machine to stop. Unless the machine is fitted with a safety brake; some parts may continue to move due to momentum. Wait for all parts to stop; then disconnect it from the air line before making any adjustments, carrying out maintenance operations or just finishing using the tool.
• Remove and check setting tools. Some machinery requires the use of additional tools or keys to set, load or adjust the power tool. Before starting the power tool always check to make certain they have been removed and are safely away from the machine.
• Prevent unintentional starting. Before connecting any machine in to the air supply, make sure the switch is in the OFF position. If the machine is portable; do not hold the machine near the switch and take care when putting the machine down; that nothing can operate the switch.
• Concentrate and stay alert. Distractions are likely to cause an accident. Never operate a power tool if you are under the influence of drugs (prescription or otherwise), including alcohol or if you are feeling tired. Being disorientated will result in an accident.
• Have this tool repaired by a qualified person. This tool is designed to confirm to the relevant international and local standards and as such should be maintained and repaired by someone qualified; using only original parts supplied by the manufacturer: This will ensure the tool remains safe to use.

GENERAL SAFETY INSTRUCTIONS FOR COMPRESSED AIR
Following Safety instructions should be strictly followed. Failure to do so may result in accidents, equipment malfunctioning, serious personal Injury and / or loss of life.
Compressed air is a source of considerable energy. When handling products dealing with compressed air, the following precautions must be taken to prevent accidents.

1. Ensure that compressed air is not blocked or in contact with any part of your body.
2. Before connecting any pneumatic equipment to the compressed air supply, all mounted fittings, piping assemblies and electrical connections should be checked for security. All plastic plugs in the equipment used for protection during shipping should be removed.
3. No piping alterations, removal of fittings, repairing of equipment etc. Should be attempted with air supplies connected. Air and electrical supplies must be disconnected before beginning any adjustment, maintenance or dismantling of equipment.
4. The maximum allowable operating pressures, temperature, flows etc. must be strictly observed. Failure to do so might result in catastrophic failure of equipment, and result in serious personal injury and / or death. Refer to individual catalogues for this information, and any other operating or application limitations.

WARNING:

1. Compatibility of pneumatic equipment
   Ensuring the compatibility of the procured FRL equipment is the responsibility of the person who designs the Pneumatic system and/ or System specifications. This should be based on specifications or after analysis and / or tests to meet specific requirements.

2. Repair & Maintenance
   Assembly, handling, or repair of pneumatic systems should be performed by only trained and experienced operators.

3. Safety First
   Do not service machinery/ equipment or attempt to remove any component until safety Is confirmed.

4. Inspection and maintenance of machinery/ equipment should only be performed after confirmation that both compressed air and electrical supply have been positively disconnected and all residual compressed air in the system has been completely exhausted to the atmosphere.

5. Contact the manufacturer if equipment is to be used in any of the following conditions:

6. Equipment is to be used in conditions beyond the given specifications, or if equipment is to be used outdoors.

7. Equipment is to be used in conjunction with atomic energy, railroad, air navigation, automobiles or related vehicles, medical equipment or safety equipment.

8. In applications that adversely effect humans, animals, or property requiring special safety analysis.

ADDITIONAL SAFETY INSTRUCTIONS FOR AIR RATCHETS
Important: Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you.

• Power tools shall not be used in potentially explosive atmospheres unless specifically designed for that purpose;
• Unexpected tool movement due to reaction forces or breakage of inserted tool or reaction bar may cause injuries;
• Power tools shall be isolated from the energy source before changing or adjusting the inserted tool;
• Warning:
  • There is a risk of crushing by torque between a reaction bar and the workpiece;
  • There is a risk of loose clothing, hair etc., being caught in the rotating spindle of the tool;
  • There is a risk of being injured if hands are not kept away from the reaction bar, specially observed when unscrewing in confined work spaces;
  • There is a risk of being injured if hands are not kept away from the nutrunner sockets;
  • There is a risk of danger to persons from high speed splinters being emitted from impact wrenches in the case of nutrunner socket failure.
  • There is a risk of being injured by whipping air hoses.
• Unexpected direction of inserted tool movement can cause a hazardous situation;
• Use only sockets and adaptors which are in good condition and are intended for use with power tools;
• Adopt a suitable posture to counteract normal or unexpected movement of the power tool due to reaction forces from the power assembly tool;
• Release the start and stop device in the case of an interruption of the energy supply;
  • Only lubricants recommended by the manufacturer shall be used;
• Release pressure when not in use. Disconnect from air line;
  • Air ratchets are not torque wrenches and are not designed or capable of installing fasteners to a specified torque. For fasteners requiring a specific torque, install the fastener to well below the required value then complete the task with a hand torque wrench to avoid damaging the fastener or workpiece.
• Only use accessories specifically hardened for impact use. Do not use standard chrome type hand tool sockets as they will shatter and splinter causing injury.
• Do not modify this impact wrench in any way.
• Do not carry or move the tool by the air line.

TECHNICAL DESCRIPTION

IDENTIFICATION

1. Trigger switch.
2. ½” Square drive.
3. 360° adjustable exhaust port.
4. Reverse/forward selector.
5. Speed selector.
6. Composite body.
7. ¼” BSP air inlet.

UNPACKING AND CHECKING

PACKAGING
Carefully remove the product from the packaging and examine it for any sign of damage that may have happened during shipping. Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Helpline (the telephone number appears on the Title page) and do not attempt to use the product.
The packaging material should be retained at least during the guarantee period: in case the product needs to be returned for repair.
Warning! Some of the packaging materials used may be harmful to children. Do not leave any of these materials in the reach of children.
If any of the packaging is to be thrown away, make sure they are disposed of correctly; according to local regulations.

WHAT’S IN THE BOX?
Lay out the contents and check off the items against those featured below.

Airline coupling screw adaptor

AIR SUPPLY

AIR TOOL OIL SPECIFICATION
Air tool oil viscosity refers to it’s properties to flow and how it reacts with heat. A low viscosity is thinner than a high viscosity.
Air tool oil becomes thinner as it heats so choosing the right viscosity is essential. If the viscosity is too low it may provide insufficient lubrication when heated. Equally, if it is too high, the fluid may provide excessive resistance to move through the lines when cold.
The ISO (International Standards Organization) viscosity grading system measures the kinematic viscosity in centistokes (cSt) at 40° which is todays accepted standard. The SAE (Society of Automotive Engineers) viscosity grade value is based on a scale.
This equipment is suited to an ISO grade 22 – 32 (SAE grade 5W – 15W) monograde oil.
The oil must be constantly supplied to the equipment during use to ensure complete lubrication and optimum performance is achieved. It also acts as a rust inhibitor when the equipment is not in use.

We recommend the use of Draper Air Tool Oil:

This air tool operates at a maximum pressure of 90psi and must be controlled via a combination pressure regulator, in-line lubricator and moisture filter such as the Draper range (see you local Draper stockiest) which with proper maintenance will ensure a constant supply of dry air and lubricating oil at all times (see illustration below). Always check machine operating pressure before use.
Water in the compressor tank will cause serious corrosion to your air tools and should be drained daily to avoid excessive water in your air supply. Dirty wet air rapidly shortens the life of your air tool.
If you are using an air tool on a hose over 25ft long it is advisable to increase the bore of the hose to the next larger size available, i.e., 1/4″ increases 3-8″. This will ensure adequate pressure and volume of air to power the machine.

RECOMMENDED AIR SUPPLY SET UP- FIG.1

ASSEMBLY

Warning!

• Failure to follow these instructions will lead to premature malfunction of the equipment which is not covered by the guarantee.

NOTE: Disconnect from the air supply before carrying out adjustment, servicing or maintenance.

CONNECTION TO THE AIR SUPPLY

• FIG.2

To connect the air nibbler to an air line, a 1/4″BSP male thread whip hose®** will be required.

• Wind a length of PTFE tape®* around the thread of the whip hose.
• Attach the hose via the 1/4″ BSP (female) air inlet CI). The connection must be tight for an airtight union.
• PTFE tape I Stock No.63389
  **1/4″BSP whip hose I Stock No.54438

OPERATION

Note: Disconnect from the air supply before carrying out adjustment, servicing or maintenance.

TRIGGER SWITCH – FIG. 3
Note: Before connecting the air ratchet to the air supply reduce the line pressure according to the specification.

• Confirm direction of rotation prior to starting. Pull trigger CD to operate the air ratchet.
• Release the trigger to stop the air ratchet. Note: Before tool operation and work commences, ensure the compressor reservoir is drained of condensate along with all connected air lines. Check and drain the air line regulator’s water trap and fill up the lubrication reservoir.

FORWARD/REVERSE
SELECTION – FIG. 4
Note: Air ratchets are not torque wrenches and are not designed or capable of installing fasteners to a specified torque. For fasteners requiring a specific torque, use a hand torque wrench.

• Rotate the selector ® anti-clockwise to select forward or clockwise for reverse operations.

SPEED REGULATION – FIG. 5
Rotate selector CD to regulate the speed most appropriate for the application.

ANVIL- FIG. 6

• Ensure the socket correctly locates on the anvil ® firmly engaging on the locating ball.
  Warning: Only use accessories specifically hardened and designed for use with impact tools. Do not use standard chrome type hand tool sockets and accessories as they may shatter and splinter.

EXHAUST PORT – FIG. 7

• Adjust the exhaust port CID away from yourself and ensure it does not agitate any dust in close proximity.

MAINTENANCE

Warning!

• Disconnect from the air supply before carrying out any adjustments, servicing or maintenance.
• Never use any sockets or accessories that are not hardened for impact use.

EVERY-DAY MAINTENANCE CHECKS
Before connection to the air supply:

• Drain the compressor reservoir of condensate.
• Drain the air lines of condensate.
• Drain the combined separator filter, regulator, water trap.
• Fill up the combined separator filter, regulator, lubricant reservoir. Check the line pressure is correct for the tool.

AFTER USE MAINTENANCE CHECKS

• Repeat the above procedures.
• Lubricate the tool with approximately 1.5ml of oil directly down the air inlet.

TROUBLESHOOTING

TROUBLESHOOTING GUIDE

tool lubricating oil into air inlet.

Operate trigger in short bursts.

| Disconnect air line supply, then turn spindle by hand.

Reconnect air supply.

| If motor fails to turn return to service centre.
Tool runs slowly. Air flows freely from exhaust.| Rotor vane seized.| Pour air tool lubricating oil into air inlet.
| | Operate tool in short bursts.
| | Tap motor housing gently with plastic mallet.
| | If still not functional, return to service centre.
Spindle seized.| Motor vane broken.| Return to service centre.
Tool will not shut off.|  ‘O’ rings throttle valve dislodged from seat inlet valve.| Replace ‘O’ ring or return to service centre.

EXPLANATION OF SYMBOLS

EXPLANATION OF SYMBOLS

Read the instruction manual.

Wear safety glasses.

Wear ear defenders.

Wear protective gloves.

Long and loose hair must be contained or securely tied back.

Do not abandon into the environment.

Keep out of the reach of children.

Warning!

Warning! Risk of crushing.

Direction of rotation.

DISPOSAL

DISPOSAL

• At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations.
  Contact your local authority for details of collection schemes in your area.

In all circumstances:

• Do not dispose of power tools with domestic waste.
• Do not incinerate.
• During decommissioning of the equipment, certain hazards should be understood and avoided:
  • Only with the line pressure released shall the equipment be disassembled.
  • Goggles should be worn.

CONTACTS
Draper Tools Limited, Hursley Road, Chandler’s Ford, Eastleigh, Hampshire. SO53 1 YF. U.K. Delta International BV, Oude Graaf 8, 6002 NL, Weert, Netherlands
Helpline: (023) 8049 4344
Sales Desk: (023) 8049 4333
Internet: drapertools.com
E-mail: sales@drapertools.com
General Enquiries: (023) 8026 6355

Service/Warranty Repair Agent:
For aftersales servicing or warranty repairs, please contact the Draper Tools Helpline for details of an agent in your local area.

YOUR DRAPER STOCKIST _____

DBMC0622
CPublished by Draper Tools Limited.
No part of this publication may be 19produced, sto1’9d in a 1’9trieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>