HAMPTON BAY KDV3384-SSW Shaker Assembled Double Oven Kitchen Cabinet Instruction Manual
- June 12, 2024
- HAMPTON BAY
Table of Contents
HAMPTON BAY KDV3384-SSW Shaker Assembled Double Oven Kitchen Cabinet
Product Information
The Oven Cabinet & Deep Bridge Cabinet is designed to provide a built-in appearance for your oven. The set includes one overhead Deep Bridge Cabinet and is the same depth as standard base cabinets. The tall oven cabinet is suitable for double ovens or combination oven/microwave units and features a bottom drawer and a double-door Deep Bridge Cabinet at the top. The bottom drawer can be removed and used as a warming oven.
The oven opening may need to be trimmed to fit your selected oven unit. Please refer to the appliance manufacturer’s specifications to determine the final cut-out size. Fillers are available for purchase separately if your oven is smaller than the minimum size opening.
Product dimensions:
- Oven Width: 24″ (61 cm) minimum, 30″ (76.2 cm) maximum
- Oven Height: 47 5/8″ (55.24 cm) minimum, 52 1/8″ (55.24 cm) maximum
Materials to build the platform for supporting the oven are not included. You will need 3/4″ or thicker plywood, 2 x 4 lumber, brackets, and screws to construct the platform.
Product Usage Instructions
- Before installation, mark all stud locations on the wall.
- Move the Oven Cabinet into position in the cabinet run without the oven and without connecting the overhead Deep Bridge Cabinet.
- Remove the drawer box from the Oven Cabinet.
- Ensure that electrical outlets are visible at the back of the cabinet.
- Align the oven cabinet face frame with adjacent base cabinet face frames.
- Use a level to check for plumb and adjust with shims if necessary.
- Attach the oven and neighboring base cabinet using #8 x 2 cabinet screws through the face frames.
- Attach the cabinet to wall studs using #10 x 2 1/2 cabinet screws through the top cabinet and drawer areas. Drill a 3/16″ pilot hole at the stud locations through the back panel and into the stud.
- Ensure that the screws are positioned at least 1″ away from the top, bottom, and sides.
- If the oven cabinet placement is not aligned with wall studs, use anchor bolts to secure the cabinet to the wall.
OVEN CABINET & DEEP BRIDGE CABINET
GABINETE PARA HORNO Y GABINETE DE UNIÓN PROFUNDO
ASSEMBLY & INSTALLATION INSTRUCTIONS
Your Oven Cabinet comes with one overhead Deep Bridge Cabinet, and these instructions will provide direction on installing both, together, to give your oven a built-in appearance. To that end, the Oven and Deep Bridge Cabinet are the same depth as standard base cabinets.
This Oven Cabinet and Deep Bridge Cabinet should be installed by an experienced cabinet installer. This guide is not intended to be a substitute for installation experience. The below instructions assume efforts will be made, before beginning, to identify problem areas where the floor/wall may not be level. Installation can be done by one person, but is easiest with two people.
NOTE: Oven and overhead Deep Bridge Cabinet should be anchored to studs in the wall and adjoining wall/base cabinets. On Deep Bridge Cabinets: any cabinet this deep should be supported by at least 3 points of contact, when installing. READ THESE INSTRUCTIONS COMPLETELY PRIOR TO BEGINNING THE INSTALLATION. AWC DOES NOT WARRANT THE INSTALLATION OF THIS PRODUCT.
Tall oven cabinets are built to contain double ovens or combination
oven/microwave units and feature one drawer at the bottom and a double-door
Deep Bridge Cabinet at the top (in one of three heights, 12”, 18” or 24”). The
bottom drawer may be removed and used for a warming oven.
The oven opening may need to be trimmed to fit your selected oven unit. See
appliance manufacturers specs to determine final cut out size; the table below
provides a range:
Some ovens may be smaller than the current minimum size opening; if so, there are 3” and 6” H fillers available, for purchase separately, in every finish. Leave a minimum of 1 1/2” W on right and left sides. Trim the height on the bottom rail by 1 1/2” maximum, and on the top by 3” maximum.
Removing rails & stiles:
You can use a square-head (Robertson bit) to remove screws from horizontal
rails. Remove inner-most pocket screw with a square-head drill bit (Robertson
bit) before cutting oven opening to a larger size.
For further trimming:
Check your oven manufacturer’s cut-out opening width and height to ensure you
get the proper opening size when fitting your oven to the cabinet. Make oven
opening alterations prior to installing cabinet. Cut opening in cabinet back
to allow access to electrical outlets. For trimming white and gray vinyl
finish cabinets, it is crucial that a very sharp blade is used to avoid
damaging the edges of the vinyl. Trim only from the outside of the piece, not
where the screws are pocket bored.
Double Oven Wall Cabinet – cutout sizes
| Cutout Minimum| Cutout Maximum
Oven Width| 24″ (61 cm)| 30″ (76.2 cm)
Oven Height| 47 5/8″ (55.24 cm)| 52 1/8″ (55.24 cm)
Build a platform to support oven: Materials to build the platform (3/4”
plywood, 2 x 4 lumber, brackets and screws) are not included.
Build an oven support platform and sub-base using 3/4” (or thicker) plywood,
and check its position within the cabinet, without anchoring platform
permanently in place yet. (Fig. 1 and Fig. 2). The top of this platform must
be level with lower edge of oven opening; double-check with a level, and shim
as needed. Lower the oven into opening in cabinet, resting it on the platform,
to fit test the size. Then remove oven, to begin the cabinet install.
Mark all stud locations on wall prior to installation. Move Oven Cabinet into position (without oven in it, and without overhead Deep Bridge Cabinet connected) in the cabinet run. Remove the drawer box. Ensure electrical outlets are visible at back of cabinet. Align oven cabinet face frame to adjacent base cabinet face frames. Use level and check for plumb of unit, using shims where necessary. Use #8 x 2” cabinet screws to attach oven and neighboring base cabinet through face frames. Use #10 x 2 1/2” cabinet screws to attach cabinet to wall studs through the top cabinet and drawer areas. Drill a 3/16” pilot hole at the stud locations through the back panel and into the stud. Make sure to position screws 1” or more from the top, bottom and sides. If the oven cabinet placement isn’t aligned to wall studs, use anchor bolts to secure cabinet to the wall.
Now secure the platform (built from plywood/ lumber, not included) to the Oven
Cabinet sides Fig. 1 Fig. 2 (again, the top of platform must be level with
lower edge of oven opening). This can be done using angle brackets (not
included) or by screwing through cabinet side panels (into 2 x 4 lumber legs)
before attaching to adjoining wall and base cabinets. If the Oven Cabinet is
at the end of a cabinet run, use angle brackets to anchor cabinet to the
floor. If you need to do this, install angle brackets in the space where the
oven will be placed prior to building oven support platform.
Follow manufacturer’s instructions for installing oven unit, including their
attachment method for anchoring the oven to the cabinet’s face frame.
- These are suggestions only. Support structure (not included) for oven may be done in various ways.
Install overhead Deep Bridge Cabinet:
To Install the overhead Deep Bridge Cabinet, follow instructions for
installing wall cabinets (included in Bridge Cabinet packaging), as in Fig. 4.
The 12” H and 18” H bridges are installed directly on top of the Oven Cabinet,
and are screwed in from the face frame of the Deep Bridge Cabinet to the oven
frame, along the back, side and top. Anchor the bridge to the studs in the
wall, as well.
Deep Wall Bridge With 96” H cabinet ordered:
The 96” Oven Cabinet comes with a Deep Bridge Cabinet that is 23 1/2” H. In
order to lift the bridge by 1/2” to reach a 24” required height, there is a
filler, called a Frame spacer (as in Fig. 5), included with this bridge
cabinet only that goes along the front and sides between
the top of the Oven Cabinet and the Deep Bridge Cabinet. This side frame
spacer ensures we reach the full (Comes in three pieces) (Viene en tres
piezas) overall height of 96” H for the entire cabinet. Start by installing
the side frame spacer directly to the top Fig. 4 Fig. 5 Deep Bridge Cabinet of
the oven cabinet. Note that this comes in 3 separate pieces. Start by nailing
the front piece into the frame. The side pieces are grooved and can be lined
up with the top of the cabinet and then nailed in from the top. Then install
the Deep Bridge Cabinet so that it rests on top of the side frame spacer, so
everything is flush at the front.
NOTE: It is critical that the bridge cabinet isn’t mounted only at the back (to wall studs). It needs to be mounted on the top side walls of the Oven Cabinet, and thru their front face frames; this means securely anchoring the two pieces together, and both individually to studs in the wall at 1” or more from the top, bottom and sides; if possible, connect these to any other adjacent overhead wall cabinets. The lower part of the Oven Cabinet can be secured by connecting to adjacent base cabinets. TIP: Whenever drilling into a cabinet frame, back panel, wall cleat, etc., it is recommended to pre-drill a pilot hole first to help prevent splitting.
We have partnered with BILT™ to provide 3D interactive instructions for this product. Download the free BILT™ app to a mobile device and search “Woodmark”
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>