HAMPTON BAY Navali Changing LED Indoor Smart Hubspace Ceiling Fan Instruction Manual

INSTRUCTIONS FOR OPERATION
Instruction Manual

SETING THE OPERATING CONTROLS

1. This unit operates on AAA*2PCS.; 3 volts battery (not included).
   To prevent possible damage if the battery should leak, be sure to remove the battery when the unit is not use.

2. Store the controller away from excess heat or humidity.

3. This remote-control unit is required with 35bit code combinations. To prevent possible interference from or to other remote units such as garage door openers, car alarm or security system.

4. Operation buttons on the panel of transmitter.
   | key| For FAN ON/OFF control .
   ---|---|---
   | key
   key| For Fan speed up control .
   For Fan slow down control .
   | key| For fan natural wind speed control
   | Key| Close Fan after 2 hours
   | Key| Close Fan after 4 hours
   | Key| Close Fan after 8 hours
   | Key| Fan learning
   | Key| Fan and Light ON/OFF control
   | Key| For Light ON/OFF control
   | Key
   Key| For Light Dimming – brightening
   For Light Dimming – dimming
   | Key| For COLOR TEMP

GENERAL INFORMATION:

This remote controller is designed to separately control your ceiling fan speed and light brightness.

INSTRUCTIONS FOR INSTALLATION AND OPERATION OF FAN SPEED CONTROLLER

Setup for ceiling fan controller

1. Turn off the power. (In order to make sure the electricity is entirely released, please press any button on the controller till no LED display showing)
2. Turn on the power
3. Press the FAN OFF button for more than 3 sec. The ceiling fan controller will have 2 blinks. It means the setup is successful. You could start to control the ceiling fan light and fan speed.

NOTICE:

The changes or modifications not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment.

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

Canada, Industry Canada (IC) Notices This device complies with Canada license- exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device. Canada, Avis’s industry Canada (IC)

Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under portable exposure conditions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>