FEIT Electric BOLLARD, SYNC, SOL, BZ Solar Bollard Light

Product Safety Information

READ BEFORE INSTALLATION AND SAVE THESE INSTRUCTIONS

CAUTION: Contains one 18650 rechargeable lithium-Ion battery. Risk of fire, explosion, or burns. Do not disassemble. Do not crush or damage the battery. Do not heat or incinerate. Do not open or disassemble. Do not make modifications to this product.
WARNING: Dispose of used battery promptly according to local recycling or waste regulations. Keep battery out of reach of children and its original package until ready to use. Clean battery contacts and unit contacts prior to installing new battery. Ensure that the battery is installed correctly with regard to polarity(+ and -).

HOW SOLAR LIGHTS WORK:
Solar panels convert sunlight into electricity. During the day, while the sun is shinning, electricity converted by the solar panel is stored in the rechargable battery. At night, the solar light is powered by the battery using the electricity stored during the day. The operating time depends on geographical location, daily weather conditions and season.

CHOOSING THE RIGHT LOCATION:
It is important to select a location with as much sunlight as possible. Shady areas will not allow the battery to be fully charged and will reduce the nighttime working hours. Be sure that the selected location is not close to other nighttime light sources such as streetlights or porch lights. These light sources may keep the solar lights from turning on automatically.

DUSK TO DAWN OPERATION:
This product is designed to only operate at night. The light will remain off during the day and tum on automatically at dusk and remain on for up to six hours.
NOTE: To make sure this function works properly, the switch must be in the selected color position.

Product FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

RF Exposure: The equipment has been evaluated to meet general RF exposure requirement The device can be used in portable condition without restriction.

Product Limited Warranty

This product is warrantied to be free from defects in workmanship and materials for up to three years from date of purchase. If the product fails within the warranty period, please contact feit electric at info@feit.com, visit feit.Com/contact-us for instructions on replacement or refund. Replacement or refund is your sole remedy. Except to the extent prohibited by applicable law, any implied warranties are limited in duration to the duration of this warranty. Liability for incidental or consequential damages is hereby expressly excluded. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

Pre-Installation

TOOLS REQUIRED

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

Part/Description/Quantity

• AA: Bollard Light: 1
• BB: 7 in. Pole: 1
• cc: Ground Stake: 1

Pre-Charge

For best performance, charge the unit for two (2) days prior to use

• Remove the insulating tab.

• In order to properly charge, the unit must be turned OFF. Use the On/Off/Cycle
  button to cycle through all of the colors (Soft White, Bright White, Cool White, Daylight, Deluxe Daylight, Red, Blue, Green, Yellow, Orange, Purple, Teal, and Pink) and reach the OFF position .

• Select a location with as much sunlight as possible.)

• After the unit has charged in the sun for two (2 days, turn it back on by pressing the On/Off/Cycle button and selecting the color of your choice. If there is daylight outside, it will stay on for about
  10 – 20 seconds and then turn off. If it is nighttime, the unit will remain on.

Bollard Light Installation

Peel off the sticker from the solar panel and remove the insulating tab

• Peel off the sticker from the solar panel.
• Remove the insulating tab.
• It is recommended that you charge the unit for two (2) days before use to adequately charge the battery, following the Pre-Charge instructions.

Installing the stake

• Push the ground stake (CC) into the ground. Using rubber mallet, insert ground stake (CC) deep enough into the ground to ensure fully assembled bollard light (AA) is stable and does not tip over.

IMPORTANT: Do not push on the bollard light (AA) or you may damage the unit.
NOTE: When installing product in hard or dry U soil, water the soil several hours beforehand to make the installation easier. You can also break up the ground lightly with a stake or a fork. Don’t force stake into the ground as excess force can break or bend the stake.

Installing the Bollard Light

• Align the bollard light (AA) with the slot on the 7 in. pole (BB). Slide the bollard light (AA) downward then turn clockwise.
• Slide the bollard light (AA) downward until it sits squarely on the stake.
• Rotate the bollard light (AA) clockwise to lock in.

Operation without Remote

For expanded control, this OneSync Bollard Light is compatible with OneSync remote or WiFi Bridge (sold separately).

DUSK-TO-DAWN OPERATION
The unit will automatically turn on at dusk and remain on through the night for 6 hours. The unit will remain off throughout the day, until dusk. NOTE: To make sure this function works properly, always have the switch in the ‘ON’ position (including daytime).

Turning on the Bollard Light

• Turn the on bollard light (AA) by pressing the on/pairing button on the side of the unit.
• Light can only turn On and stay On at nighttime.

Selecting a Color

• To cycle through the colors, push the button.
• Colors are: Soft White, Bright White, Cool White, Daylight, Deluxe Daylight, Red, Blue, Green, Yellow, Orange, Purple, Teal, and Pink.
• The bollard light (AA) will remember the color setting when next turned on.

IMPORTANT: Light brightness is determined by the charge level of the batteries. Brightness will decrease during operation to extend battery life. Selecting a color, other than white, will extend battery life.

Operation with Remote (sold separately)

Operating with a OneSync remote allows for expanded control. Modify settings of individual OneSync units or multiple units in groups.
The OneSync Remote has a 100ft control range and will command all paired units within 100ft of the remote.

All OneSync units are equipped with a signal repeater that will repeat any remote commands to all other units within 100ft. Placing units within 100ft of at least one other unit creates a control network and allows for unlimited remote control range, as long as there is a functioning OneSync unit within 100ft to relay the command.

Example: You can install a OneSync unit, then another OneSync unit 100ft away from the first unit. Continue to install 3 more OneSync units in this way so that the last unit is 500ft away. Using this relay technology, the remote will control the farthest unit that is 500ft away.

Entering pairing mode

• Hold down the pairing button for 3 seconds. Once the bollard light (AA) starts to blink slowly it is in pairing mode. The bollard light (AA) remains in pairing mode for three minutes before timing out.

Pairing the remote to the Bollard Light

• While the bollard light (AA) is in pairing mode, press and hold the desired Groups button (1, 2, 3, 4, 5 or 6) for 3 seconds to pair the remote to the selected group.
  The light will flash once, and the unit will exit pairing mode.

Unpairing the Bollard Light from the remote

• To unpair, first follow step 1 so that the unit is in pairing mode. Once the unit is in pairing mode, on the OneSync remote, press the pairing group button and hold the power button for 3 seconds. The light will flash once and the unit will exit pairing mode.
• The light will flash once, and the unit will exit pairing mode.
• To unpair from all groups at once, hold down button on the OneSync unit for 1 O seconds.
• It will flash three times rapidly to indicate that that all groups have been unpaired from the unit.

NOTE: The remote comes equipped with a universal Group #1. To create unique groups, pair using Groups #2-6. U All unit are pre-paired to the universal Group #1 so that they will immediately respond with any remote Group

1 command. To not operate on this universal group, follow the unpairing

instructions in Step 3.

Battery Replacement

Replacing the battery

• To replace the rechargeable battery, remove the lid on the side of the bollard light (AA) by unscrewing the lid screws (2) using a Phillips head screwdriver.
• Replace current lithium-ion battery with a new lithium-ion 18650 2600mAh 3.6V minimum 9.36Wh only.

WARNING: Install battery correctly with regard to the polarity(+ and -).

• Reattach (the lid) by lining up the rivet on the inside of the lid with the corresponding opening on the base (located directly above the On/Off button). Once lid is resting squarely on the base, insert and tighten the (2) screws using a Phillips head screwdriver.

Setup with Smart Bridge

Downloading and installing the Feit Electric app

• Search for the Feit Electric app in the App Store or Google Play Store.
• Download and Install the Feit Electric app on your smart unit.
• Connect to a 2.4GHz Wi-Fi network that covers your installation location.
• Follow the instructions in the Feit Electric app & Smart Bridge manual to pair your OneSync lights.

Troubleshooting

Questions, problems, missing parts?
Before returning to store, visit feit.com/help for further assistance.
FEIT ELECTRIC COMPANY I PICO RIVERA, CA I www.feit.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>