AquaticLife Auto Shut-Off Float Valve Installation Guide

June 12, 2024
AquaticLife

AquaticLife Auto Shut-Off Float Valve

AquaticLife-Auto-Shut-Off-Float-Valve-product

Product Information

Aquatic Life Float Valve Kit

The Aquatic Life Float Valve Kit is designed to automatically fill large tanks, containers, and aquariums with water. It includes an auto-shutoff solenoid that ensures the system stops filling the container once it reaches the desired water level. The kit connects to a faucet and can be used with reverse osmosis (RO) units for filtered water.

Specifications

  • Minimum Operating Pressure: 40 PSI
  • Maximum Operating Pressure: 80 PSI

Product Parts List

  • Auto-Shutoff Solenoid
  • Adjustable Float
  • Rubber Washer
  • 1/4 Inline Check Valve
  • 1/4 x 1/2 FPT
  • 5′ – 1/4 Polyethylene Tubing
  • Installation Guide

Important Notes

  • The check valve arrow must point in the direction of water flow.
  • The auto-shutoff solenoid must be installed with the screw-side at the bottom.
  • The float valve must be installed in the recommended orientation to work properly.
  • Mark all tubing 5/8 from the end and insert it into fittings until it reaches the mark.
  • Aquatic Life assumes no responsibility for water damage due to leaks. It is the user’s responsibility to determine that the system is leak-free.

Product Usage Instructions

  1. Insert tubing from the supply water connection into the IN port of the auto-shutoff solenoid (non-screw side).
  2. Insert tubing into the OUT port of the auto shut-off solenoid (non-screw side) and connect the other end of the tubing to wherewater flows into the sediment cartridge.
  3. Install the adjustable float into a reservoir or other container.
  4. Connect the tubing from the filtered water existing the membrane to the inline check valve. Be sure the arrow on the check valve is pointing in the direction of water flow.
  5. Insert tubing to connect the check valve to the IN port (screw side) of the auto-shutoff solenoid.
  6. Insert the tubing into the OUT port (screw side) and connect the other end of the tubing to the adjustable float valve.
  7. Connect the waste water to drain and insert the flow restrictor.

Connection

The Aquatic Life Float Valve Kit allows you to automatically fill large tanks, containers, and aquariums.AquaticLife-Auto-Shut-Off-Float-Valve-fig
1

INSTALLATION

  1. Insert tubing from the supply water connection into the IN port of the auto-shutoff solenoid (non-screw side)
  2. Insert tubing into the OUT port of the auto shut-off solenoid (non-screw side) and connect the other end of the tubing to where water flows into the sediment cartridge
  3. Install the adjustable float into a reservoir or other container
  4. Connect the tubing from the filtered water existing the membrane to the inline check valve. Be sure the arrow on the check valve is pointing the direction of water flow
  5. Insert tubing to connect the check valve to the IN port (screw side) of the auto-shutoff solenoid
  6. Insert the tubing into the OUT port (screw side) and connect the other end of the tubing to the adjustable float valve

PARTS LIST

Auto-Shutoff Solenoid| 1/4″ x 1/2″ FPT
Adjustable Float| 5′ – 1/4″ Polyethylene Tubing
Rubber Washer| Installation Guide
1/4″ Inline Check Valve|

PRODUCT SPECIFICATIONS

PRODUCT SPECIFICATIONS

Minimum Operating Pressure: 40 PSI
Maximum Operating Pressure: 80 PSI

Float Valve Kit With Automatic Shutoff

  • Fill large tanks, containers, and aquariums automatically
  • Includes auto-shutoff solenoid
  • Connects to faucet

Aquatic Life is trademark of Lifetime Products LLC.

ITEM # 500300

Documents / Resources

| AquaticLife Auto Shut-Off Float Valve [pdf] Installation Guide
Auto Shut-Off Float Valve, Shut-Off Float Valve, Float Valve, Valve
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals