Softub Spas 140 Largest Mobility Showroom Instruction Manual
- June 12, 2024
- Softub Spas
Table of Contents
140 Largest Mobility Showroom
Product Information
The product is a Softub hot tub available in three sizes: 140, 220, and 300. The product comes with straps for the cover and plumbing connectors. The product also has a hydromate and a light connector. The product comes with a liner and a control panel with an air control. The product has a Water Care Guide for chemical levels and maintenance.
Product Usage Instructions
- Place the straps for the cover on the ground in an X patternwith the back side of the buckle facing up so the buckle attaches properly on the lock. The plumbing connectors need to be between the straps.
- Twist the connectors in a clock-wise fashion until the connectors are snug and no threads are showing.
- Connect the light connector and make note of your two serial numbers for warranty registration.
- Run the hose for 2 to 3 minutes in the garden, yard or down a drain before beginning to fill the tub. This will help to clear out any algae or debris that is in the hose. When done, begin filling the tub.
- After filling the tub with about 2 inches of water, smooth out any wrinkles on the bottom of the liner by moving the liner around with your hands and fingers. Tucking the liner in the bottom edges helps to alleviate the wrinkles.
- Continue filling the tub until it reaches approximately 2 inches below the top of the liner.
- With the tub running, check the chemical levels and adjust them as necessary as advised in the Water Care Guide.
- Open the air control on the control panel by rotating counter-clockwise for 15 minutes after adding the chemicals.
- After 15 minutes, close the air control by rotating it counter-clockwise until it stops and put the lid on the tub.
Roll up your sleeves and set up the Softub! Do not use a razor knife to open the box. Use the claw end of a hammer to tear the flaps open.
BOX INCLUDE
These are the items you received and will need. Please note that the filter is probably already installed in the tub. Please leave it installed on the wall of the tub.
INSTALLATION
Place the straps for the cover on the ground in an “X” pattern. The back side of the buckle should be facing 3 up so the buckle attaches properly on the lock. The plumbing connectors need to be between the straps.
Verify the placement of the straps under the tub. You can dry-fit the cover at
this point in time to make sure the straps are installed correctly. Line up
the connectors on the power unit with the connectors on the tub. The power
unit is not to be plugged in yet! 
Twist the connectors in a clock-wise fashion until the connectors are snug and
no threads are showing. 5 Connect the light connector. *Make note of your two
serial numbers for warranty registration. 
Run the hose for 2 to 3 minutes in the garden, yard or down a drain before
beginning to fill the tub. This will help to clear out any algae or debris
that is in the hose. When done, begin filling the tub. 
After filling the tub with about 2 inches of water, smooth out any wrinkles on
the bottom of the liner by moving the liner around with your hands and
fingers. Tucking the liner in the bottom edges helps to alleviate the
wrinkles. 
Make sure the filter is installed if not installed already. Soak filter in warm water prior to installing to ease installation. Fill tub to a level 2 inches above the highest jet.
DO NOT PLUG IN THE TUB YET! 
Check the tub connections for leaks. Simply tighten the connectors a little
more if there is a leak. Plug the tub in now. 
Check for leaks while the tub is running. If there are leaks, tighten the
connectors. Now install the foam and vinyl connector covers. 
With the tub running check the chemical levels and adjust them as necessary as
advised in the Water Care Guide. Open the air control on the control panel by
rotating counter-clock-wise for 15 minutes after adding the chemicals. After
15 minutes, close the air control by rotating it counter-clockwise until it
stops and put the lid on the tub. 
Set the tub to your desired temperature and make sure to lock your cover. Your
tub is now heating and will shut off when the desired temperature is reached.
The tub heats at 1 to 1.5 degrees per hour. 
Enjoy your bath!
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>