Fast and Furious TIRAMISUBEST Electric Longboard Skateboard Instruction Manual
- October 30, 2023
- Fast and Furious
Table of Contents
- Warning
- Introduction of Electric skateboard
- Precautions for use
- Introduction of remote control
- OLED DISPLAY
- board battery status:
- Operate Instruction
- Operating limits
- MAXIMIZING RANGE
- Troubleshooting
- Other safety warnings
- Maintenance and repair
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
TIRAMISUBEST Electric Longboard Skateboard
Instruction Manual
Warning
You should read, understand and abide by the terms and conditions of the user
guide before riding skateboard.
Riders may risk death or serious injury from loss of control and falls. Always
wear helmet and protective gear such as knee pads, eloow pads, wrist pads
while riding skateboard.
DO NOT ride the board if you are under the age of 16 years old.
Avoid riding on uneven surfaces, dirt, sand, steep hills, cracks, rocks might
cause a fall. Be cautious when going down hills.
enskate is not liable for any damage caused by unsafe operation or faulty
repair, any repairs made by unauthorized technicians will avoid the warranty.
Introduction of Electric skateboard
2-1 What’s in the box
2-2(1) Schematic diagram and description of skateboard
2-3(1) Specification parameters:
Specification/Material Size | 970*275mm |
---|---|
Net weight | 8kg |
Plate material | Carbon fiber |
Endurance | 30-40km |
Maximum speed | 40km/h |
Climb angle | 30% |
Maximum loadbearing | 150kg |
Motor | 600w*2 hub motor |
Battery performance | 9600MAH |
Maximum Range and hill climb depends on road condition, terrain and temperature.
2-2(2) Schematic diagram and description of skateboard
2-3(2) Specification parameters:
Specification/Material Size | 970*275mm |
---|---|
Net weight | 8kg |
Plate material | Epoxy resin adhesive |
Endurance | 30-40km |
Maximum speed | 40km/h |
Climb angle | 30% |
Maximum loadbearing | 150kg |
Motor | The belt motor 600w*2 |
Battery performance | 9600MAH |
Maximum Range and hill climb depends on road condition, terrain and temperature.
2-2(3) schematic diagram and description of skateboard 2-3(3) Specification parameters :
Specification/Material Size | 970*335mm |
---|---|
Net weight | 12 kg |
Plate material | Carbon fiber |
Endurance | 40km |
Maximum speed | 50km/h |
Climb angle | 35% |
Maximum loadbearing | 150kg |
Motor | 1000w*2 |
Battery performance | 9600MAH |
Maximum Range and hill climb depends on road condition, terrain and temperature.
2-2(4) Schematic diagram and description of skateboard 2-3(4) Specification parameters :
Specification/Material Size | 1080*430mm |
---|---|
Net weight | 12 kg |
Plate material | 10 layers of maple |
Endurance | 40km |
Maximum speed | 50km/h |
Climb angle | 35% |
Maximum loadbearing | 150kg |
Motor | The belt motor 1750w*2 |
Battery performance | 9600MAH |
Maximum Range and hill climb depends on road condition, terrain and temperature.
2-2(5) Schematic diagram and description of skateboard
2-3(5) Specification parameters :
Specification/Material Size | 985*215mm |
---|---|
Net weight | 7.2kg |
Plate material | 7 PLY and Baboo |
Endurance | 15-20km |
Maximum speed | 35km/h |
Climb angle | 30% |
Maximum loadbearing | 120kg |
Motor | 600w*2 |
Battery performance | 4400MAH |
Maximum Range and hill climb depends on road condition, terrain and temperature.
Precautions for use
Driving wheels Right after long-term use, do not touch the rear axle or driving motor. The driving motor produces heat and may cause serious burns. Cool down these areas before touching.
Description of battery recharging:
Charging Method: Connect the standard charger AC with 100-240VAC socket.
Insert the DC terminal into charging port at the bottom of the skateboard.
Charger indicator light turns red means connection is completed, and the
battery is charging, Charger indicator light turns green means charging is
completed, then remove all plugs.
Battery Handling & Disposal
Your skateboard may not have a fully-charged battery when first received.
Accordingly, you should charge the battery prior to the first use. Optimal
conditions for the battery: Temperature 10-24°C (50-75°F), Humidity 45-85%.
NO RIDING AT/BELOW FREEZING TEMPERATURE
Never store or use the battery at freezing or below freezing temperature.
Make sure to turn off the skateboard after riding it, depleted battery might
cause damage. Charge the battery at least once a month even if not using
it.Use only the enSkate charger and caution when charging. The cord, plug,
enclosure and other detail parts require periodic inspection for possible
damage. The charger should be operated only by adult. Do not use charger near
flammable materials. Unplug the charger and disconnect it with skateboard
when charging is completed.
Introduction of remote control
4-1 Schematic diagram and description of remote control
OLED DISPLAY
board battery status:
The the remote control connects with the e-board successfully as the pictures
shows,The “BO”stands for the e board power with 4 blank to indicates the
power.when the power is lower than10%,the power indication blank will twinkle
0.5s and the remote vibrates twice.
Remote battery status:
Switch on the remote control power,as the picture shows, “RM” stands for the
remote controlpower with 4 blanks to indicates the power.when the power is
less than 5%,the e board cannot be speed up and the remote control only have
the “brake control” function.
4-1 (2) Schematic diagram and description of remote control
OLED DISPLAY
E- board battery status:
The the remote control connects with the e-board successfully as the pictures
shows, The “BO”stands for the e board power with 4 blank to indicates the
power.when the power is lower than10%,the power indication blank will twinkle
0.5s and the remote vibrates twice.
connect skateboard and remote :
turn on the remote and the board, then long press the power key of the board
until it flashes. Then press the speed key and the set key meanwhile. When the
power is displayed at Bo on the remote, indicating the connection is
successful.
4-2 Remote battery status
Switch on the remote control power,as the picture shows, “RM” stands for the
remote controlpower with 4 blanks to indicates the power.when the power is
less than 5%,the e board cannot be speed up and the remote control only have
the “brake control” function.
4-3 Radio interference precautions
Skateboard incorporates a sophisticated communication system to ensure
connection between the remote control and the skateboard. The connection could
be unstable or lost when the remote control’s battery is low. Stop riding when
the low battery warning sign appears. Try to avoid areas with high-power
electromagnetic radiating equipment, such as radio towers, power lines and
radar. In some rare cases, connection may also be lost due to unpredictable
causes. As a safety precaution, skateboard will shut off immediately when the
connection lost. If losing connection happens more than once, stop use it
immediately and contact with enSkate customer support team.
Operate Instruction
5-1 Turn on skateboard
You can slide the board or press the power button to turn on the skateboard.
Slide to start:
Slide the board till you hear the beep, battery indicator and power switch
indicator lights up means the board was turned on. Sliding too slow or too
soft might not able to turn on the board.
Power saving : Leave the board for 3 minutes and it will automatically
turn off.
Power button:
Press the power button and hear the beep, battery display lights on means the
board was turned on.
Charge the battery before using skateboard
5-2 Turn on remote control and start operation
5-2-1. Press the power switch of the remote control for three seconds to turn
on the remote control. Press the power button for 3-5 seconds or leave the
board for 3 minutes and it will automatically turn off.
Try repair the skateboard with remote if it’s not successfully paired. (Check
5-3)
5-2-2. The default speed of the skateboard is 0-16kmh (0-10mph). Firstly, as
shown in the figure, pull the remote accelerator rocker to braking position,
so that the dynamic wheel is under damping braking status.
5-2-3. Prepare for riding and keep the correct riding position. As shown in
the figure, according to individual customs, step on the skateboard; place
both feet on the skate- board, keep knees bent and look ahead.
(Please wear protective gear while riding skateboard)
5-2-4. After moving into a stable standing position, push the accelerator
rocker to the middle position. Push the accelerator upwards slowly until the
skateboard moves slowly and keeps sliding conditions. After stabilizing, push
the accelerator forwards or backwards to adapt speed levels and brake
sensitivity.
The default speed of the skateboard is set up to 16kmh(10mph) with remote
paired. Do not push the accelerator rocker too fast before operating
killfully.
Wear helmet and protective gear while riding.
5-3 Pairing
turn on the remote and the board, then long press the power key of the board
until it flashes. Then press the speed key and the set key meanwhile. When the
power is displayed at Bo on the remote, indicating the connection is
successful.
5-4 Switch direction
The remote control has a direction button, press up is forward, press down is
backward. Forward and backward have four gears respectively, according to the
speed gear and can be adjusted.
5-5 Power Off
5-5-1:Turn off skateboard : Press the power button for 6-8 seconds or leave
the board for 2 minutes and it will automatically turn off.5-5-2:Turn off
remote : Press the power button for 3-5 seconds or leave the board for 3
minutes and it will automatically turn off.
Operating limits
It is important that you are familiar with the limits of skateboard, which to maximize rider’s safety and reduce the risk of damaging skateboard. The skateboard will perform better when you observe these limits.
WEIGHT LIMITS FOR RIDERS AND CARGO
ANZO sets weight limits for two reasons:
- Rider safety
- To reduce the risk of damaging skateboard
CAUTION: Exceeding the weight limit, especially in situations requiring
more power when combined with other variables, will reduce the speed range of
skateboard, or increase the risk of damaging skateboard.
Variables that require more power include:
- Higher payloads (weight of rider and all cargo)
- Steeper slopes Bumpy or rough surface conditions Excessive starting, accelerating, and stopping
STRUCTURAL WEIGHT LIMITS (MAXIMUM PAYLOAD)
The maximum payload (rider plus all cargo) is 80kg (176lbs). Exceeding the maximum weight limit increases the risk of damaging skateboard.
Several factors affect the loads transmitted to the skateboard:
- Rider’s riding skill
- Payload (weight of the rider and all cargo)
- Surface condition (obstacle height, etc.)
NOTICE: Exceeding the weight limits, especially when riding on uneven terrain, could damage the skateboard or reduce the performance quality.
MAXIMIZING RANGE
Maximum range distances are provided in the Technical Specifications section.
The range of your skateboard is affected by many variables, including:
- Terrain: Riding on smooth, flat terrain improves range, and riding on hilly terrain and unpaved surfaces reduces range.
- Speed and Riding Style: Riding at a consistent, moderate speed will increase range. Excessive starting, stopping, acceleration, and deceleration reduces range.
- Rider Weight and Cargo: Lighter riders with less cargo experience better range than heavier riders with more cargo.
- Temperature: Storing, charging, and riding in temperatures close to the median of the recommended temperature range improves range. Riding in colder temperatures reduces range significantly.
- Battery Condition: Correct charging method and maintaining can extend the battery’s lifespan to provide longer range. Battery with poor condi- tion will provide less range.
Troubleshooting
If your skateboard is not running properly, stop using it immediately. In most cases, turning the skateboard off for ten seconds and restarting it will solve the issue. If you find other problems, or restarting the skateboard doesn’t resolve he issue, refer to the following chart for common troubleshooting methods. If t t he problem still exists, please stop using the skateboard and contact enSkate.
Trouble | Probable Cause | Solution |
---|---|---|
Not turned on | Low Battery | Charge battery for at least one hour |
Not riding | I. The remote control is not connected or not turned on | Restart |
the remote and skateboard
2. Skateboard/remote in sleep mode| Shut both down for ten seconds, then turn
on again ten seconds later
Not charged| 1.Charger not connected| Make sure you’re using the correct
charger and that it is properly connected to an outlet
2.Battery depleted| If battery has not been charged for more than a month, it
may require an extra hour to start normal charging
Range too low| Exceeded the weight
limit| The skateboard can only carry up to 80kg (176Ibs)
Vibration and
noise| 1.Loose screws| Tighten the screws
2.Wheel/Bearing has worn down| Replace wheel/bearing
Replacable tire and motor
PU tires replacement instruction: Loosen 6 screws with hexwrench then pull out
the PU tire, insert the new one into the motor hub, and tighten the screws to
complete the replacement.
Driving wheels High temperature warning: Risks of burns. Right after long-term use, do not touch the rear axle or driving motor. The driving motor produces heat and may cause serious burns. Cool down these areas before touching.
Other safety warnings
SAFETY WARNINGS
A. General Disclaimer
- Riding skateboard can be a dangerous activity, certain conditions may cause the equipment failure. Like other electric transportation products, falling, losing control, collisions, including failure to obey the user manual, may cause injury even death. In order to minimize the risk, ensure you read the user manual carefully.
- RIDE AT YOUR OWN RISK AND USE COMMON SENSE.
- This manual contains many warnings and cautions concerning the consequences of failing to maintain, inspect or properly use your skateboard. We repeat: any accident may result in possible serious injury or death.
- WEAR HELMET AND PROTECTIVE GEAR AT ALL TIMES.
B. Riding Instruction And Tips
- In any case, we always recommend using remote control.
- Emergency brake while riding with high-speed is dangerous, you may need to rely on skating techniques like foot-braking for a gently brake.
- You can always loose the throttle before the brake.
- To quit the cruise control mode, you can gently push the rocker till the orange light stops flashing, then increase the speed or take a brake.
- Emergency brake and acceleration is not recommmended with cruise control mode.
C. Age, Weight & Health
- Skateboard is not designed for riders under 16. Keep skateboard away from children, young teens.
- DO NOT ride the board if you are under the influence of alcohol or drugs.
- DO NOT exceed the weight limit of 80kg (1761bs).
D. Conditions For Safe Riding
-
Ride it defensively in safe location. Watch out for potential obstacles that could catch your wheels, force you to swerve suddenly, or lose control. Be careful to avoid pedestrians, motor vehicles, other skateboarders, scooters, bikes, children or animals that may enter your path.
-
Always wear proper protective equipment such as an approved safety helmet (with chin strap securely buckled), wrist guards, elbow pads, and knee pads. A helmet may be legally required by local law or regulations in your area. A long-sleeved shirt and long pants are recommended. Before riding, be sure to check that all wheels, trucks and the battery case are secured properly.
-
WARNING: AVOID WATER
enSkate woboard mini’s water resistant level is IP54, but it is not completely water-proof. Do not ride in the rain, wet or icy weather, as the electrical and drive components could be damaged. Always ride on dry, paved surfaces. -
NO TRICKS
Do not attempt or do stunts or tricks on your skateboard. Skateboard is not made to withstand abuse from misuse such as jumping, curb grinding or any other types of stunts. Skateboard can break from the stress incurred by these activities. Any such misuse will void the warranty. -
KEEP fingers, hair, and clothing away from motors, wheels and all other moving parts.
Maintenance and repair
10-1 Clean
- For your safety and to avoid potential safety problems, do not wash the board directly with water, only use damp cloth to clean the surface.
- It is strictly forbidden clean all the sliding interface by damp cloth, including battery connector, battery output interface and etc.
10-2 Maintenance
- Termly check if the screws loose.
- For storage, stored the board in a dry and ventilated environment, do not in the sun or hot and humid environment.
- For long term storage, suggest to full-charge the battery every month and keep the board on 10-30 minutes.
- Unplug all plugs or connectors after the battery is fully charged.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>