INOKRAFT Drizzle D1 LVLP Air Spray Gun User Guide

INOKRAFT Drizzle D1 LVLP Air Spray Gun

This guide is for quickly starting spray painting projects. For detailed product and safety information please refer to the user manual.

KNOW YOUR SPRAY GUN

NOZZLE SIZE RECOMMENDATION
Please refer to the Paint Manufacturer’s recommendations.

NOZZLE SET REPLACEMENT

Disassembly of nozzle set

1. Turn the Fluid Adjustment Knob(D) counter clock- move the Fluid.
2. Needle and Needle Spring.
3. Remove the Air Cap Set(A).
4. Unscrew the Fluid Nozzle with the Adjustment Wrench.
5. Reverse for assembly and remember to tighten the Fluid Nozzle to prevent fluid leak.

NOTE
Replace the whole set of Air Caps, Nozzle, and Fluid Needle at the same time.

ASSEMBLY

1. Install the Filter. Screw the Paint
   NOTE: dockwise. using other paint cups, please choose a compatible adapter. The paint cup inlet thread size is MI6X1.5.(An adapter for 3M PPS Series 2.0 is included.)

2. Optional Connect the Air Pressure Regulator to the Inlet Connector(G) and then the Oil-Water Separator.

3. Use a 1/4″ air hose to connect with the Oil-Water Separator or connect directly to the Inlet Connector(G).

STARTUP

1. Turn the Air Pressure Regulator Knob clockwise to make sure the closet is Turn the Fluid Adjustment Knob(D) clockwise to the Piven the needle from moving.
2. Turn the Pattern Adjustment Knob(C) counterclockwise to fully open the fan.
3. Turn the Air Adjustment Knob(F) counterclockwise to fully open it.
4. Hold the Gun regulator Knob counter the raise Pressure up to Turn the Fluid Adjustment Knob(D) to gauge #2.
5. Change the spray pattern critical by rotating the Air Cap at 90° Mix the coating material by the Manufacturer’s instructions and pour it into the Paint Cup.

TEST SPRAY

1. Test the static and dynamic spraying effect on the test paper.

2. Adjust knobs to get the right coating result and pattern.

3. If the finish is too dry, turn the Air Adjustment Knob(F) clockwise to reduce the inlet air pressure.

4. If the finish is too wet, turn the Fluid Adjustment Knob(D) clockwise to reduce the fluid flow.

5. If the atomized particles are too coarse, turn the Air Adjustment Knob(F) counterclockwise to increase the inlet air pressure.

6. If the atomized particles are too fine, turn the Air Adjustment Knob(F) clockwise to reduce the inlet air pressure.

7. If the spray pattern is too large, turn the Pattern Adjustment KnobC) clockwise to reduce the size.
   NOTE: Refer to the User Manual for more information

8. Record relevant data on the test card for next use (optional).

SPRAY

1. Maintain a distance of 6-8 inches between the spray gun and the object surface. Keep the spray gun perpendicular to the surface during the move– menu. Bending or tilting the spray gun will cause uneven spraying.
2. Slightly press the trigger to start the stroke, then press hard, to get a smooth gun activation and save paint. (Practice makes perfect!)
3. To stop spraying, slightly release the trigger to end the stroke, then release the trigger completely.
4. The speed of moving the spray gun is recommended to be about 12-15 inches per second.
5. When spraying large areas, it is recommended to use a reciprocating method. The overlap area of the spray width is about 50%.
6. After using the spray gun, be sure to turn off the air source. Then hold the trigger to release the air pressure.

CLEAN UP

1. Recycle the remaining paint into the paint container.

2. Pour in neutral cleaning solution (pH 6 to 8), shake lightly and spray it out. Repeat multiple times until the mist coming out is clean.
   NOTE : Do not immerse the spray gun completely in any solvent or cleaning solution, as this will damage the spray gun lubricant and shorten its lifespan.

3. Disconnect the air hose, disassemble the Paint Cup(B), Air Cap Set(A) and Fluid Adjustment Knob(D). Use a cleaning kit and accessories to completely clean the gun.

4. Clean the air cap, nozzle and fluid needle by brushing the outer surface.

5. Clean the air cap hole with a toothpick. (if necessary)
   NOTE: If using metal wire or hard tools, be careful not to scratch the air cap hole to become fuzzy, resulting in the deformation of the spray pattern.

6. Clean the Paint Cup and Gun Body by wiping the surface with a damp cloth.

7. After cleaning, reconnect to the air hose, turn up the inlet air pressure and hold the Gun Trigger(E) to dry the inside of the spray gun.

Please refer to the User Manual for detailed instructions on how to use and maintain the LVLP spray gun.

Questions?

Don’t hesitate to drop a message at support@inokraft.com!

Join the InoKraft Community for INSTRUCTION VIDEOS FREE ACCESSORIES FREE TRIALS OF NEW PRODUCTS EXTENDED WARRANTY by sending “I’m a draftsman” and your purchase order ID to support@inokraft.com or Scan:

Official Youtube www.youtube.com /@inokraft

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>