Weidm ller Wallbox AC SMART User Manual

: October 30, 2023
: Weidm ller

Table of Contents

Scope of delivery
Safety note
Disposal
Safety Precaution
Assembly and installation instructions
- Power supply cable
Technical data
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Weidm ller Wallbox AC SMART

Scope of delivery

ECO
PLUG
SOCKET
VALUE
PLUG
SOCKET
ADVANCED
PLUG
SOCKET

Safety note

These instructions are part of the product.

If you hand over the product to a third party, always hand over the instructions as well. These instructions are intended for the installer of the product.
Read the instructions completely before you install and start using the product.
Check with the responsible grid operator regarding applicable regulations and provisions for charging boxes.
You can download an acceptance protocol for initial commissioning from the Weidmüller website.

| The operating instructions can be downloaded from the Weidmüller product catalogue.
---|---
| Assembly and installation may only be carried out by an electrician.

Risk to life due to electric shock

There is a risk of electric shock when working on the electrical installation of the product.

Ensure that the following equipment is present in the domestic installation:
- one ground residual current protective switch for each charging point in accordance with DIN EN 61008-1, DIN EN 61009-1
- one circuit breaker for each charging point in accordance with DIN EN 60898, DIN EN 60947-2
Ensure that voltage is switched off to the product and feed line before beginning assembly and installation work on the product.
Observe the requirements for the installation site (see technical data).
Ensure correct wiring.
Carry out a visual inspection and create an acceptance protocol before initial commissioning.

Incorrect installation may cause water to get into the product. This could result in an electric shock.

The IP protection class is only achieved if the product is assembled and installed as described in this documentation.
Only install the product in the direction shown in these instructions.
Only use the cable bushings with suitable cable glands and sealing elements. Ensure correct installation.
Only operate the product if it has been assembled and installed as described in this documentation.
Do not use a pressure washer to clean the EV charging box.
Only clean the EV charging box with a soft, lightly moistened cloth.

Risk to life due to fire

Incorrect installation may cause lines to be damaged or the product to overheat. This could result in a fire.

Observe the requirements for the installation site (see technical data).
Only install the product in the direction shown in these instructions.
16 A variation: install a supply cable with a wire cross-section of at least 2.5 mm2.
32 A variation: install a supply cable with a wire cross-section of at least 6 mm2

Foreign objects or dirt in the plug contacts can cause a fire.

Check the plug contacts for foreign objects and contamination.
Do not insert any objects into the plug contacts.
Remove light contamination, for instance dust or sand, by blowing it out.
Heavy contamination must be cleaned by an electrician

Risk of death due to blocked escape routes

An improper installation site may cause escape routes to become blocked or create a tripping hazard.

Ensure that the installed product does not block any escape routes.

Risk of injury if product is damaged

A damaged or incomplete product can lead to malfunctions and hazards.

If you store the product before installation, observe the storage information in these operating instructions.
Only begin installation if all articles in the scope of delivery are present and complete.
Only begin installation if all components are free from damage.
Check the EV charging box and its accessories for obvious damage before each use.

Risk of injury from falling parts

Incorrect installation may cause the product or parts thereof to fall and injure personnel.

Ensure that the subsurface has a sufficient load-bearing capacity.
Use the included installation material for installation on a concrete wall (see scope of delivery).
Use suitable installation material for installation on a wall made of another material. Note the product weight (see technical data).
Do not place any objects on the installed housing.

Possible destruction of the product

The connection terminals of the neutral conductor must be connected in all network systems. Incorrect installation may cause the destruction of the product.

Only install the product only as described in these instructions.

Disposal

| Observe the notes for proper disposal of the product. You can find the notes here: www.weidmueller.com/disposal.
---|---

Safety Precaution

Assembly and installation instructions

| Power supply cable
---|---
| Optional cables (communication)
| Charging cable (only PLUG variant)

Optional cable glands (communication)

$Optional cable glands $communication$$

| Power supply cable
---|---
| Optional cables (communication)
| Charging cable (only PLUG variant)

Power supply cable

| 16 A| 32 A
---|---|---
min. / max.| 2,5 mm² – 16 mm²
AWG 14 – AWG 4| 6 mm² – 16 mm²
AWG 10 – AWG 4
H05(07) V-U, min. / max.| 2,5 mm² – 16 mm²| ² 6 mm² – 16 mm²
H07V-R, min. / max| 6 mm² – 16 mm²| 6 mm² – 16 mm²
H05(07) V-K, min. / max.| 2,5 mm² – 16 mm²| 6 mm² – 16 mm²

Power supply cable

wire end ferules| | | DIN 46 228/4
DIN 46 228/1
---|---|---|---
| | | Order no.
2,5 mm²| 20 mm
18 mm| H2,5/25T GR H2,5/18| 9021090000
9004090000
6 mm²| 20 mm
18 mm| H6,0/26 SW H6,0/18| 0565700000
9004130000
10 mm²| 21 mm
18 mm| H10,0/28 EB H10,0/18| 0565800000
0379300000
16 mm²| 21 mm
18 mm| H16,0/28 GN H16,0/18| 0566000000
0375200000

Optional: Limit max. charging current, charging phases and max. assymetrical current / configure network settings

Web server: 192.168.0.8
Role: Admin
Password: zyVt45Nv0y
In order to prevent unauthorised access you should change the login data immediately.

Go to charge settings:
Config / General / Charge settings / Installation current limit [A] Config / General / Charge settings / Charging phases
Config / General / Charge settings / Max current asymmetrical [A]

Optional: Cover VALUE / ADVANCED

Only PLUG variant

Download:

Optional: Signal cable / data cable

| Pos.| Label| Function
---|---|---|---
| X5.1| B| RS485 Modbus RTU Signal B/-
X5.2| A| RS485 Modbus RTU Signal A/+
X5.3| GND| Ground
X5.4| RED| Digital output, status LED red
X5.5| GN| Digital output, status LED green
X5.6| BL| Digital output, status LED blue
X5.7| DO| Digital output, configurable
X5.8| GND| Ground

| Pos.| Label| Function
---|---|---|---
| X6.1| DI1| Digital input, configurable, 12 V
X6.2| DI2| Digital input, configurable, 12 V
X6.3| DI3| Digital input, configurable, 12 V
X6.4| DI4| Digital input, configurable, 12 V
X6.5| DI5| Digital input, configurable, 12 V
X6.6| GND| Ground
X6.7| 12V| Supply voltage 12 V
X6.8| 12V| Supply voltage 12 V

Optional: Energy meter VALUE / ADVANCED

Control box

| Signal / data cable
---|---
min. / max.| 0,13 mm² – 1,5 mm²
AWG 28 – AWG 14
H05(07) V-U, min. / max| 0,2 mm² – 1,5 mm²
H05(07) V-K, min. / max.| 0.2 mm² – 1,5 mm²
wire end ferules| DIN 46 228/4
---|---
| | | Order no.
0,25 mm²| 10 mm| H0,25/12 HBL| 9025760000
0,34 mm²| 10 mm| H0,34/12 TK| 9025770000
0,5 mm²| 10 mm| H0,5/14 OR| 0690700000
0,75 mm²| 10 mm| H0,75/14T HBL| 9021040000

Optional: Load management / charge management VALUE / ADVANCED

Load management / charge management

VALUE| static
ADVANCED| dynamic

Technical data

Charging current, max.

Width x height x depth
Weight
Housing impact resistance rating
Operating temperature
Storage temperature
Relative humidity during operation
Relative humidity during storage
Degree of protection
Pollution severity
Protection degree
Phases
Rated voltage
Rated current
Rated impulse voltage
Insulation voltage
Overvoltage category
Mains frequency
Circuit breaker max. 1)
Charging voltage
Charging power, max.
Short circuit current C16/C32 (energy limit class 3)
AC residual current protective switch 1)
DC fault-current detection integrated
Network design
Charging mode
Supported charging states
EMC classification
Socket in accordance with IEC 62196-1:2014 for charging cable
Plug in accordance with IEC 62196-1:2014 for charging cable
Permitted setup area
Static load/charge management integrated
Dynamic load/charge management integrated
MD conforming energy meter integrated
Mobile app
Supported network protocols
Mobile phone
Interfaces
Digital inputs
Digital outputs

must be present in the domestic installation

**ADVANCED**

22 kW: 6.9 kg

| 11 kW: 4.3 kg

22 kW: 4.3 kg

IK10| IK10
-25 °C bis +45 °C| -25 °C bis +45 °C
-25 °C bis +70 °C| -25 °C bis +70 °C
5 … 95 % (non-condensing)| 5 … 95 % (non-condensing)
5 … 95 % (non-condensing)| 5 … 95 % (non-condensing)
IP54| IP54
3| 3
I| I
1… 3| 1… 3
207 … 253 V / 360 … 440 V| 207 … 253 V / 360 … 440 V
16 A| 32 A| 16 A| 32 A
4 kV| 4 kV
500 V| 500 V
III| III
50 / 60 Hz| 50 / 60 Hz
16 A| 32 A| 16 A| 32 A
230 / 400 V| 230 / 400 V| 230 / 400 V| 230 / 400 V
11 kW| 22 kW| 11 kW| 22 kW
6 kA| 6 kA
Type A 30 mA| Type A 30 mA
6 mA| 6 mA
TN / TT / IT| TN / TT / IT
3| 3
A, B, C, E, F| A, B, C, E, F
Class B| Class B
–| Type 2
Type 2| –
indoor, outdoor| indoor, outdoor
x| x
x| x
x| x
x| x
Modbus RTU / TCP, OCPP 1.6 (J)| Modbus RTU / TCP, OCPP 1.6 (J)
x| x
Bluetooth (Low Energy), WLAN (802.11