OSD P83 MK2 Patio Speaker Installation Guide

: October 30, 2023
: OSD

Table of Contents

Preparation:
Considerations
Placement
Installation:
Wiring
Specifications
WARRANTY
Documents / Resources

P83 MK2 Patio Speaker

OSD P83 MK2 Patio Speaker Installation Guide

Preparation:

Tools For Installation

Pencil
Drill
Tape Measure
Wire Cutter
Phillips Screwdriver
Utility Knife
Safety Eye Wear
Gloves

Speaker Wire Guide
18AWG minimum – for distances up to …………………. 10 ft
16AWG – from …………………………………..…… 10 to 50 ft
14AWG – from ……………………………………… 50 to 100 ft

Considerations

– Where is the best place to install the speakers?
– Where do the speakers sound the best?
– Separate the speakers 6 – 10 feet apart.

Placement

These weather resistant patio speakers are manufactured to resist a variety of weather condition. The most ideal place to install these speakers is the undersides of most eaves and overhangs as they provide the best protection. Like all speakers, they sound the best when placed no more than six to ten feet apart from each other, and slightly higher than ear level. If the speakers are more than ten feet apart, toe them in toward the center of the listening area.
(NOTE) These speakers are not waterproof and cannot be submerged under water.

Installation:

Mounting
If your application requires the speaker to be mounted, please follow these directions. Using the hardware supplied, mount the bracket first. Attach the speakers to the brackets using the large plastic knobs supplied. Never mount a speaker on a wall made of unreinforced drywall or plasterboard. If you are unsure, consult a professional contractor. To install the speaker to the bracket. Screw the bracket knobs into the cabinet. Point the speaker toward the listening area. Once the direction of the speaker has been determined tighten the bracket knobs securely. (See Diagram 1.)

OSD P83 MK2 Patio Speaker - fig

Mounting Options
The mounting bracket has the agility to tilt and swivel to suit your particular application or listening preference.
(See Diagram 2.)

OSD P83 MK2 Patio Speaker - fig 2

Wiring

The binding post speaker terminals on the speakers will accommodate up to 12-guage wire. Connect the speaker cable to the speaker cable terminals, matching the proper polarity with your amplifier, + to + (red) and – to – black). Make sure to connect the right channel to the right speaker and the left channel to the left speaker. Either channel may be attached to either terminals set, however, be sure that polarity ( + and – ) is correct on each channel or the performance of the speaker will be seriously affected as one channel will cancel out the other.
The P83 MK2 is equipped to play as a standard 8 Ohm speaker or as a 70V/100V speaker. Choose the correct setting on the back using the dial to match your application. (See Diagram 3.)

OSD P83 MK2 Patio Speaker - fig 3

Specifications

P83 MK2

8” 2-Way Patio Speaker
Woofer: 8” Graphite Cone
Tweeter: 1” Silk Soft Dome
Power Handling: 80W program, 50W RMS
Sensitivity: 90dB 1w/1m
Freq Response: 56Hz-20kHz +/-3dB
Impedance: 8 ohms
70V Settings: 0, 25W, 12.5W, 6.25W, 3.12W
100V Settings: 0, 50W, 25W, 12.5W, 6.25W
IP Rating: IP66
Weight: 9.96lbs
Dimensions: HxWxD 14.17” x 9.65” x 9.06”

WARRANTY

All Optimal Speaker Design outdoor speakers have (2) year Limited Warranty against defects in materials and workmanship. Proof of purchase must accompany all claims. During the warranty period Optimal Speaker Design will replace any defective part and correct any defect in workmanship without charge for either parts or labor
Optimal Speaker Design may replace returned speakers with a product of equal value and performance. In such cases, some modifications to the mounting may be necessary and are not Optimal Speaker Design’s responsibility.
For this warranty to apply, the unit must be installed and used according to its written instructions. If necessary, repairs must be performed by Optimal Speaker Design. The unit must be returned to Optimal Speaker Design at the owner’s expense and with prior written permission.
Accidental damage and shipping damage are not considered defects, nor is damaged resulting from abuse or from servicing performed by an agency or person not specifically authorized in writing by Optimal Speaker Design Optimal Speaker Design sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any Optimal Speaker Design product purchased from an unauthorized dealer or other source, including retailers, mail order dealers and online sellers will not be honored or serviced under existing Optimal Speaker Design warranty policy. Any sale of product by an unauthorized source or other manner not authorized by Optimal Speaker Design shall void the warranty on the applicable product.
Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis of the retail value of the parts and labor. To return for repairs, you must email customer service at RMA@audiogeargroup.com for a Returned Merchandise Authorization (RMA) number then the unit must be shipped to Optimal Speaker Design at the owner’s expense, along with a note explaining the nature of service required. Be sure to pack the product(s) in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit.
This Warranty Does Not Cover: Damage caused by abuse, accident, misuse, negligence, or improper operation (installation) • Any products that have been altered or modified • Any product whose identifying number of decal, serial #, etc. has been altered, defaced or removed • Normal wear and maintenance.

Optimal Speaker Design
Brea, CA osdaudio.com
P83 MK2 Manual. 7/22