BLACKSTONE 6001 5 x 8 Feet Bar and Grill Owner’s Manual

BLACKSTONE 6001 5 x 8 Feet Bar and Grill

IMPORTANT :

This instruction manual contains important information necessary for the proper assembly and safe use of the appliance.
Read and follow all warnings and instructions before assembling and using the appliance.
Follow all warnings and instructions when using the appliance.
Keep this manual for future reference.
Installer/Assembler: leave these instructions with the consumer.

For the latest version of this manual, scan this code or visit BlackstoneProducts.com/support

SAFETY ALERT KEY

Indicates a hazardous situation that, if not avoided, will result in death or serious injury.

Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.

Indicates a hazardous situation that, if not avoided, could result in death or serious injury.

Indicates information considered important, but not hazard related (e.g. messages related to property damage).

ASSEMBLY GUIDE

Parts List

HARDWARE

TOOLS INCLUDED

Follow all safety warnings provided with your tools.

A step-ladder (not included) is required for assembly.
Check the components against the parts list and make sure there are no missing parts.
Lay pieces on cardboard or a soft mat to help protect the pieces from scratches.

ASSEMBLY INSTRUCTIONS

Find a large, clean area to assemble your appliance.
Remove all packing material before assembling.

Sharp edges. Wear gloves while assembling.

For ease of assembly, it is recommended to have 3 or more people and allow enough time to completely finish the assembly. (Assembly can take 6-8 hours.)
DO NOT tighten screws until all the screws and washers are properly installed.

Step 01 Slide one (1) foot base cover {C} onto one (1) post 8 {A8}.
Use four (4) [AA] bolts and four (4) [HH] flat washers to attach one (1) foot base {B} to the bottom of post 8 {A8}.
Repeat with the other post 8 {A8}, and posts {A7} , {A5} , and {A2}.

Step 02 Pull the electric cord out through the plug on post 5 {A5}.
Use three (3) [KK] plastic caps, three (3) [AA] bolts, and three (3) [DD] flat washers to attach post 4 {A4} and post 5 {A5}.
Note: The FRONT arrows should face each other.
Repeat with post 6 {A6} to one (1) post 8 {A8}.
Use three (3) [KK] plastic caps, three (3) [AA] bolts, and three (3) [DD] flat washers to attach post 3 {A3} and one (1) post 8 {A8}.
Repeat with post 1 {A1} and post 2 **{A2}.

**

Step 03 Use two (2) [AA] bolts and two (2) [HH] flat washers to attach cross beam 3 {D3} and cross beam 4 {D4}.

Step 04 Use two (2) [AA] bolts and two (2) [HH] flat washers to attach cross beam 1 {D1} and cross beam 2 {D2}.

Step 05 Use two (2) [CC] bolts and two (2) [HH] flat washers to attach post assembly {A3} to roof rib 2 {F2}.
Repeat with post assembly {A1} and roof rib 1 {F1}.
Use two (2) [CC] bolts and two (2) [HH] flat washers to attach one (1) cross beam connector 1 {E1} and post assembly {A6} to roof rib 2 {F2}. Repeat with one (1) cross beam connector 1 {E1}, post assembly {A4} and roof rib 1 {F1}.

Step 06 Use four (4) [AA] bolts and four (4) [HH] flat washers to attach one (1) cross beam connector 2 {E2} to roof rib 2 {F2} and post assembly {A3}.
Use four (4) [AA] bolts and four (4) [HH] flat washers to attach one (1) cross beam connector 2 {E2} to roof rib 1 {F1} and post assembly {A1}.

Step 07 Use two (2) [AA] bolts and two (2) [HH] flat washers to attach one (1) cross beam connector 1 {E1} to roof rib 1 {F1}.

Step 08 Use two (2) [BB] bolts, four (4) [HH] flat washers, and two (2) [GG] nuts to attach cross beam connector 4 {E4} and one (1) cross beam connector 3 {E3} to roof rib 2 {F2}.

Step 09 Note: DO NOT tighten the bolts completely until all the bolts and washers are properly installed.
Use four (4) [AA] bolts and four ( 4 ) [HH] flat washers to attach one (1) support bracket 3 {K3} to post assembly {A3} and roof rib assembly {F2}.
Use four (4) [AA] bolts and four (4) [HH] flat washers to attach one (1) support bracket 3 {K3} to post assembly {A1} and roof rib assembly {F1}

Step 10 Use two (2) [AA] bolts and two (2) [HH] flat washers to attach cross beam {D1} to one (1) cross beam connector 1 {E1}. Note: the FRONT labels should face forward.
Use two (2) [AA] bolts and two (2) [HH] flat washers to attach cross beam {D2} to one (1) cross beam connector 3 {E3}.

Step 11 Use two (2) [AA] bolts and two (2) [HH] flat washers to attach cross beam {D4} to one (1) cross beam connector 1 {E1}. Use two (2) [AA] bolts and two (2) [HH] flat washers to attach cross beam {D3} to one (1) cross beam connector 1 {E1}.

Step 12
Note: DO NOT tighten the bolts completely until all the bolts and washers are properly installed.
Use four (4) [AA] bolts and four (4) [HH] flat washers to attach support bracket 1 {K1} to post assembly {A4} and cross beam {D3}.
Use four (4) [AA] bolts and four (4) [HH] flat washers to attach support bracket 2 {K2} to post assembly {A6} and cross beam {D4}

Step 13 Use two (2) [AA] bolts and two (2) [HH] flat washers to attach roof top rib 1 {G1} to roof top rib 2 {G2}.
Note: the ARROWS should face the same direction.

Step 14 Use two (2) [AA] bolts and two (2) [HH] flat washers to attach top support 1 {J1} to top support 2 {J2}.

Step 15 Use two (2) [AA] bolts and two (2) [HH] flat washers to attach roof top rib 1 {G1} to roof rib {F1}.
Use two (2) [AA] bolts and two (2) [HH] flat washers to attach roof top rib 2 {G2} to roof rib {F2}.

Step 16
Note: DO NOT tighten the bolts completely until all the bolts and washers are properly installed.
Use three (3) [AA] bolts and three (3) [HH] flat washers to attach top support 1 {J1} to post assembly {A1}.
Use three (3) [AA] bolts and three (3) [HH] flat washers to attach top support 2 {J2} to post assembly {A3}

Step 17 Use four (4)   [AA] bolts and four (4) [HH] flat washers to attach cross beam 5 {D5} to post assembly {A6} and post assembly **{A3}.

Step 18 Use four (4) [AA] bolts and four (4) [GG] flat washers to attach bottom support 1 {J3} to post assembly {A2} and post assembly {A7}

**

Step 19 Use four (4) [AA] bolts and four (4) [HH] flat washers to attach bottom support 2 {J4} to posts {A5} and {A2}.

Step 20 Use two (2) [AA] bolts and two (2) [HH] flat washers to attach shelf 2 {L2} to post {A1}.
Use three (3) [AA] bolts and three (3) [HH] flat washers to attach shelf 2 {L2} to post {A7}.

Step 21 Use two (2) [AA] bolts and two (2) [HH] flat washers to attach shelf 1 {L1} to post {A4}.
Use two (2) [AA] bolts and two (2) [HH] flat washers to attach shelf 1 {L1} to post {A1}.
Use two (2) [CC] bolts, four (4) [HH] flat washers, and two (2) [GG] nuts to attach shelf 1 {L1} to shelf 2 {L2}.

Step 22
Note: DO NOT tighten the bolts completely until all the bolts and washers are properly installed.
Use six (6) [CC] bolts, six (6) [HH] flat washers, and six (6) [EE] sealant washers to attach roof panels {M1}, {M2}, {M3}, {M4}, and {M5} to roof top ribs {G1} and {G2}.
Use two (2) [CC] bolts, two (2) [HH] flat washers, and two (2) [EE] sealant washers to attach roof panels {M1}, {M2}, {M3}, {M4}, and {M5} to cross beams {D3} and {D4}.
Note: If the holes don’t align during the assembly, pull the crossbeams outward to align the holes.

Step 23 Note: DO NOT tighten the bolts completely until all the bolts and washers are properly installed.
Use two (2) [CC] bolts, two (2) [HH] flat washers, and two (2) [EE] sealant washers to attach gutter 2 {H2} to the roof panels and cross beam **{D4}.

Step 24
Note : DO NOT tighten the bolts completely until all the bolts and washers are properly installed.
Use two (2) [CC] bolts, two (2) [HH] flat washers, and two (2) [EE] sealant washers to attach gutter 1 {H1} to the roof panels and cross beam {D3}.

**

Step 25 Use four (4) [FF] bolts to attach the electrical power cover {P} to post {A4}.
Use two (2) [AA] bolts and two [DD] flat washers to attach the bottle opener {N} to post {A1}.
Stick the magnetic hooks [LL] to the front cross beams and roof ribs. (5 per side is recommended.)

Step 26 Use four (4) [JJ] expansion bolts to anchor each post foot base {B}.

OUTDOOR STRUCTURE ANCHORING GUIDE

If your BLACKSTONE BAR & GRILL is not properly anchored, damage could occur.
It is highly recommended for maximum safety that you mount and secure to wood or concrete footers. This is far better and safer than using ground stakes

WOOD
Anchors should be drilled into joists or reinforced blocking (not only deck boards).

CONCRETE
Use a 1/2″ drill bit (not included) to pre-drill holes for concrete anchors.

If digging for foundation, please double check for possibility of any underground utilities such as gas, telephone, cable or sprinkler lines. Refer to your local building and city codes, ordinances, neigh- borhood covenants, or height restrictions regarding this type of structure for guidance on acceptable installation requirements. Consider consulting a licensed contractor for assistance in the anchoring of this product.

USING YOUR BLACKSTONE

Enjoy using your BLACKSTONE BAR & GRILL!

USING YOUR BLACKSTONE BAR & GRILL

The BLACKSTONE BAR & GRILL is intended for privacy, decorative and ornamental use only.

Product is NOT INTENDED for the following:

• A safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds.
• As load bearing support for a building, structure, heavy objects or swings.
• Used in structures that trap wind, rain or snow that would create extra load on the product.

SNOW LOAD CAPACITY

12 lbs/ ft2 = 480 lbs. of total snow load Accumulated snow must be removed from roof.

WIND RATING

Beufort scale 8 – Gale force winds (39-46 MPH)
The BLACKSTONE BAR & GRILL should not be used in inclement weather and high winds.

BLACKSTONE BACKYARD BAR & GRILL LIMITED WARRANTY

Blackstone Products warrants this Backyard Bar and Grill against defects in materials and workmanship for a period of one (1) year from the original date of purchase.
To the extent any such defects occur, Blackstone Products will send the appropriate replacement part(s) at no charge.
This warranty does not cover:

• Inspection costs or labor for replacement of any defective part(s);
• Incidental or consequential damages;
• Cosmetic defects which DO NOT affect performance or integrity;
• Normal wear and tear;
• damage due to vandalism; acts of nature, including but not limited to wind, storms, hail, floods;
• Improper assembly, installation, or use;
• discoloration or fading of the finish as a result of exposure to chemicals, spills, pool or salt water
• Corrosion/ rust.

Your Backyard Bar and Grill has been designed for safety and quality.
Any modifications made to the original product could compromise its structural integrity or function, and could lead to product failure or personal injury. As such, modifying this product voids any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY and is not for commercial, contract or other non-residential purposes. Blackstone Products disclaims all other representations and warranties of any kind, express or implied.
The warranty applies to the original purchaser and is non-transferable. It does not apply to purchases of display models, or when the product is sold on clearance or “as is”.
To activate your warranty, register your product at www.BlackstoneProducts.com/register.
North Atlantic Imports LLC makes no warranty whatsoever in respect to accessories or parts not supplied with it. This warranty shall apply only within the boundaries of the United States of America and Canada. This warranty gives the original purchaser specific rights,
and the original purchaser may also have other rights, which vary from state to state.

This product may be covered by one or more issued U.S. and/or
international patents and may include patent applications pending.
For more information, please visit: BlackstoneProducts.com/patents

References

• Register Product - Blackstone Products
• Support – Blackstone Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>