TrueCam M11 GPS 4K Car Camera User Guide

Table of Contents

TrueCam-M11-GPS-4K-Car-Camera-PRODUCT

A TrueCam M11 GPS 4K dash cam with a wide-angle lens and 2.0-inch display
Comes with a magnetic GPS module, magnetic holder with 3M adhesive pad, charger with extra USB port, micro SD/USB adapter, 3M adhesive power cable clips, cable tool, protective carry bag, 3-meter micro USB charging cable, and USB data cable for GPS module update
A supercapacitor provides power instead of a conventional battery
Records speed, and GPS coordinates, and warns of static speed cameras and traffic lights using the GPS module
Has audible sounds for approaching a speed camera, start and end of average measurement

Open the pack and take out all the contents.
Insert a Class UHS-I U3 or higher branded microSD card up to 128 GB into the camera with card connectors facing the display. Format the card directly in the camera before first use and repeat formatting at least once a month.
Insert the adapter into the car cigarette lighter and connect it to the camera holder using the USB cable. The camera turns on automatically and begins recording. For some vehicles, turn the ignition key first.
Perform basic camera settings before sticking the holder to the glass. Set up the G-sensor and choose the ideal place to mount the camera between the windscreen and the rear-view mirror.
Remove the film from the 3M adhesive pad on the camera holder. Point the camera to capture the best view before attaching it to the glass. Press the 3M adhesive pad onto the glass and hold it for a while.
Attach the magnetic GPS module to the camera mount. When connected to GPS satellites, the module’s LED flashes blue. The GPS module records speed, and GPS coordinates, and warns of static speed cameras and traffic lights using audible sounds.
To update the speed camera database, use the USB data cable provided and follow the instructions in the manual.

TrueCam-M11-GPS-4K-Car-Camera-FIG-1

TrueCam-M11-GPS-4K-Car-Camera-
FIG-2

TrueCam-M11-GPS-4K-Car-Camera-FIG-8

TrueCam-M11-GPS-4K-Car-Camera-
FIG-3

Insert the microSD card as shown into the camera (card connectors facing the display).
Use Class UHS-I U3 and higher branded cards up to 128 GB.
Only remove the card, when the camera is turned off.
When using the card for the first time, format it directly in the camera and repeat the formatting at least once a month to ensure proper camera operation.
Insert the adapter into the car cigarette lighter and connect it to the camera holder using the USB cable.
The camera is designed to operate only when connected to a power supply.
Instead of a battery, the camera contains a supercapacitor that provides power which has several times the lifespan of a conventional battery.
Camera turns on automatically and begins recording.
For some vehicles, the ignition key must be turned first.
Perform basic camera settings before sticking the holder to the glass.

G-senzor

If the G-Sensor detects an impact, it automatically protects the video currently being captured against being overwritten.
Attention, when the settings are set to high sensitivity and you are driving over uneven surfaces this can cause files to be automatically protected and the filling up of the SD card.

Motion Detection

The camera automatically starts recording when it detects movement in the lens field of view and stops recording after about 30 seconds.
If you stop recording manually or turn off the camera, motion detection is disabled.
The function is for monitoring a parked vehicle, do not use whilst driving.
To use the motion detection function, the camera must be turned on and connected to the power supply.

Parking Mode

The camera will start recording automatically when it detects a jolt to the vehicle and if it does not happen again, after about 30 seconds it stops recording and turns off.
To use the parking mode function, the camera should be turned off and connected to the power supply.

GPS module functions

The ideal place to mount your camera is the space between the windscreen and the rear-view mirror so as not to obstruct the driver‘s view.
Make sure that the glass is clean and dry at the attachment point.
The ideal bonding temperature is 20 °C – 40 °C.
Remove the film from 3M adhesive pad on the camera holder.
Before attaching it to the glass, point the camera to capture best view.
Press the 3M adhesive pad onto the glass and hold it for a while.

GPS AND SPEED CAMERA DETECTION

Attaching the magnetic GPS module to the camera mount.
When connected to GPS satellites, the module’s LED flashes blue.
The GPS module records speed, GPS coordinates and warns of static speed cameras and traffic lights.

AUDIBLE SOUNDS:

TrueCam-M11-GPS-4K-Car-Camera-
FIG-5

Connect the GPS module to a PC with an Internet connection using the included USB cable.
Open the GPS module memory (similar to a flash drive).
Run Update.exe.
Click Update.

WIFI APP

Scan the QR code or enter the URL – truecam.com/m11/app
Install the app on your smartphone or tablet.
Turn on Wi-Fi on the camera – Camera menu -> Wi-Fi -> On -> Network Name (SSID) and Password (PWD) will appear on the camera display.
On the phone/tablet, connect to the Wi-Fi network with the camera name, enter the password (factory setting- 12345678), start the RoadCam app, and click the „+“ button to connect the camera.

MORE INFORMATION

You’ll find the complete manual and firmware updates at http://truecam.com/downloads plus a special PC application for playing back videos from the camera.