PLANET Industrial IP67 PoE + Media Converter IGTP-825AT User Manual

: June 6, 2024
: PLANET

Table of Contents

Package Contents
Hardware Introduction
Installation
Product Specifications
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PLANET Industrial IP67 PoE + Media Converter IGTP-825AT User Manual

Package Contents

Thank you for purchasing PLANET Industrial IP67 1000BASE-X SFP to 10/100/1000BASE-T 802.3at PoE+ Media Converter, IGTP-825AT. In the following sections, the term “Outdoor PoE+ Media Converter” means the IGTP-825AT.

Open the box of the Outdoor PoE+ Media Converter and carefully unpack it. The box should contain the following items:

IGTP-825AT x 1
User’s Manual x 1
M22 Waterproof Cable Gland x 3
Power Cable with 2-pin Terminal Block x 1
Wall-mounted Kit x 1
Ground Wire x 1

Hardware Introduction

This section describes the functionalities of the Outdoor PoE+ Media Converter’s components.

Product Outlook

Figure 2-1: IGTP-825AT product outlook

Power Input Port

Figure 2-2 shows the power input port side of the IGTP-825AT

Figure 2-2: IGTP-825AT Power Input port side

Data Input Port and 802.3at PoE+ Output Port

Figure 2-3 shows the “Data + PoE+” output port and “Data” input port side of the IGTP-825AT.

Data Input Port and 802.3at PoE+ Output Port
Figure 2-3: IGTP-825AT RJ45 / SFP ports side

LED Indicators

LED	Color	Function
PWR	Green	Indicates it has power.
LINK/ACT	Green	Lights to indicate the port is linked up at

10/100/1000Mbps.
Blinks to indicate that the IGTP-825AT is actively sending or receiving data over that port.
LINK| Green| Indicate the port is linked up at 1000Mbps and actively sending or receiving data over that port.

To install the 2-pin Terminal Block Connector on the Outdoor PoE+ Media Converter, simply follow the following steps:

Step 1: Insert positive DC power wire into V+, negative DC power wire into V-, and grounding wire into Ground.
Step 2: Tighten the wire-clamp screws for preventing the wires from loosening and plug them into the Outdoor PoE+ Media Converter.
Note

1. The wire gauge should be in the range from 20 to 22 AWG.
2. The device must be grounded.

Installation

This section describes how to install the Outdoor PoE+ Media Converter and make connections to it. Please read the following sections and perform the procedure in the order being presented.

Installing Cable Gland with Power Cable and RJ45 UTP Cable

The cable gland consists of the following:

Installing Cable Gland with Power Cable and RJ45 UTP
Cable

Connecting Waterproof Cable Kit to the Outdoor PoE+ Media Converter

Step 1: Turn clockwise to tighten the gland body connected to the Outdoor PoE+ Media Converter.
Step 2: Plug the power cable connector into the power input port.
Step 3: Insert the sealing insert into the cable gland body.
Step 4: Attach the clamping nut to the cable gland to complete the cable assembly

Caution
Make sure the clamping nut is tightly attached to the cable gland body and the sealing insert is squeezed tightly.
Step 5: Repeat Steps 1 to 4 for “PoE (Data + Power)” Output Port.

Fiber Cable Gland Installation

Step 6: Insert the SFP transceiver into the “Data” Iutput Port
Step 7: Thread the cable gland over the fiber cable in the order as indicated below and attach the two-hole sealing to the fiber cable.
Step 8: Connect the fiber cable to the SFP transceiver.
Step 9: Turn clockwise to tighten the gland body
Step 10: Repeat Steps 3 and 4

Note

Use only the waterproof cable gland provided in the package of the IGTP-825AT.
If the above installation procedure is not properly followed, the warranty will be invalidated.
If the waterproof cable gland is found missing or damage, please contact your local reseller where you purchased from.
Never use any waterproof cable gland that is not purchased from PLANET or doesn’t have the same dimensions of the IGTP-825AT; it will damage the device permanently.

Wall-mount Installation

To install the Outdoor PoE+ Media Converter on the wall, please follow the instructions described below.

Step 1: Find the wall that you want to mount the Outdoor PoE+ Media Converter on.
Step 2: Refer to the picture below to screw the four screws on the wall.
Step 3: Use a screwdriver to screw them into the wall.

Grounding the Device

Users MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device.

Grounding the Device

Note

EMD (Lightning) DAMAGE IS NOT CONVERED UNDER WARRANTY.

Connecting IGTP-825AT to PD

Step 1: Connect the additional Cat5e/6 cable from the PoE+ Out of the IGTP-825AT to a remote PD.
Step 2: The PoE+ Out port is the power injector which transmits DC voltage to the Cat5e/6 cable and transfer data from the Data source.
Step 3: Once the IGTP-825AT detects the existence of an IEEE 802.3at/af device, the LINK/ACT LED indicator will be lit steadily, showing it is providing power.

Note

According to IEEE 802.3at/af standard, the IGTP-825AT will not inject power to the cable if not connected to a standard IEEE 802.3at/af device.

Product Specifications

|

Product

| IGTP-825AT
---|---|---
|

Hardware Specifications

DC”** out RJ45 port

Auto MDI/MDI-X, auto-negotiation RJ45 connector

| Input Power Terminal Block| 1 x 2-pin terminal block

– Pin 1/2 for Power (Pin 1: V+ / Pin 2: V-)

| Cable| 10BASE-T: UTP category 3, 5 cable (≤100m) 100BASE-TX: UTP category 5,5e cable (≤100m)
1000BASE-T: UTP category 5e,6 cable (≤100m)
1000BASE-SX/LX:

Multi-mode: 50/125μm or 62.5/125μm optical fiber
Single-mode: 9/125μm optical fiber

Power over Ethernet

PoE Standard| IEEE 802.3at Power over Ethernet Plus / End- span PSE
Backward compatible with IEEE 802.3af Power over Ethernet
PoE Power Output| 55V DC, max. 30 watts
PoE Power Supply Type| End-span
Power Pin Assignment| 1/2 (+), 3/6 (-)
PoE Power Budget| 30 watts (max.) @ IEEE 802.3at PoE+ input

Standards Conformance

Regulatory Compliance| FCC Part 15 Class A, CE
Protocols and Standards Compliance| IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet IEEE 802.3ab Gigabit Ethernet
IEEE 802.3z Gigabit Ethernet over Fiber Optic IEEE 802.3x Flow Control
IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus
Stability Testing| IEC 60068-2-32 (Free fall) IEC 60068-2-27 (Shock)

IEC 60068-2-6 (Vibration)

---|---

Environment

Temperature| Operating: -40~75 degrees C Storage: -40~85 degrees C
Humidity| Operating: 5~90% (non-condensing) Storage: 5~90% (non- condensing)

Note

The PoE power output ability will depend on the distance.

Customer Support

Thank you for purchasing PLANET products. You can browse our online FAQ resource and user’s manual on PLANET web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team.

PLANET online FAQs:https://www.planet.com.tw/en/support/faq?method=category&c1=2
Support team mail address: support@planet.com.tw