SONOFF L3 Pro RGBIC Smart LED Strip Light User Manual
- June 4, 2024
- SonOFF
Table of Contents
SONOFF L3 Pro RGBIC Smart LED Strip Light
Controller introduction
Button features
- Short press: Turn on/off the strip light
- Long press for 5s: Make strip light enter in the pairing mode (LED indicator flashes)
Short press the button to exit the pairing mode while it is in the pairing mode.
Features
L3&L3 Pro both are smart strip lights, which have 16 million colors and support switching various Scene modes through your smartphone or voice control. Also, you can select different modes based on the music styles to sync the music with gorgeous lighting.
Operation instruction
- Clean the surface
- Peel off the protective film
- Stick it on
- Download the eWeLink App
- Power onPower on the LED strip light with a Type-C USB cable, after powering on, it will enter the Bluetooth pairing mode by default and flashes.The strip lights will exit the Bluetooth pairing mode if it not be paired within 3 mins. If you want to enter this mode again, please long press the controller for 5s until the strip lights “flashes” then release.
- Add light stripTap “+” and select “Bluetooth Pairing”, then operate following the prompt on the App.
Wi-Fi Settings
Select the “Wi-Fi Settings” on the “Device Settings” interface in the eWeLink
App to add or change the network.
When Wi-Fi is disconnected, the device will automatically switch to Bluetooth
control (Ensure Bluetooth is enabled on your mobile phone).
Specifications
Models: L3-5M, L3-5M-P
Light Strips
Input Voltage | SV DC |
---|---|
Luminous Flux | L3: 150Lm L3 Pro: 160Lm |
LED QTY | L3: 90pcs L3 Pro: 1S0pcs |
IP Rating | L3: IP20 L3 Pro: IP54 |
CCT | 2500-6500K |
Beam Angle | 120° |
Life Expectancy | Appr. 30000h |
Material | FPCB |
Working temperature | -l0°C – 40°C |
LED strip length | Sm |
Controller
Input | 5V DC |
---|---|
Output | 5V DC 2A |
Max. power | 10W |
Wi-Fi | IEEE802.11 b2.4GHz |
Bluetooth standards | 5.0 BLE |
Shell material | PCVO |
Dimension | 79.5×29.5×13.5mm |
Cuttable
L3: Cut table every 55.55mm
L3 Pro: Cut table every 33.33mm
Please note that the light strips cannot be restored if you cut it.
Factory Reset
Deleting the device on the eWeLink App-indicates you restore it to factory
setting.
Safety Warning
- Before use, please confirm that the voltage is appropriate for this product’s working voltage. Using inappropriate voltage may damage the product and bring safety hazards.
- LED Light Sources are unchangeable, please don’t dismantle them.
- The Strip Lights will generate heat during working. please keep air circulation for heat dissipation.
FCC Warning
Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter.
Note :
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type L3-5M/L3-5M-P are in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/usermanuals
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>