McAlpine Plumbing HC2650UK Top Access Bath Trap with Removable Chrome Plated Clicker Waste Instruction Manual
- October 30, 2023
- McAlpine Plumbing
Table of Contents
McAlpine Plumbing HC2650UK Top Access Bath Trap with Removable Chrome
Plated Clicker Waste
Product Information
The HC2650UK is a waste and overflow kit for baths that are 5-7mm thick. It comes with three parts A, B, and C which are factory assembled. The water seal level can be adjusted b extending part C fully down and then pushing the assembly into the zwaste body, which will automatically adjust the water seal. An extension kit is available separately to use with thicker baths. The product code for the extension kit is HC2650-EXT-KIT.
The product dimensions are as follows
- 34mm – diameter of the waste outlet
- 102mm – length of the overflow pipe
- 50mm – water seal level
- 68mm – length of the extension piece
- 61mm – length of the sleeve
- 15.5 – length of the flange
- 74mm – diameter of the overflow grill
- 38mm – diameter of the waste body
Product Usage
- Start by assembling parts A, B, and C which are factory assembled.
- Insert the waste outlet (part 1) into the bath’s waste body (part 4aii or 4biv) and tighten it using the hand-tightening tool provided.
- Insert the overflow pipe (part 2) into the overflow opening on the bath and secure it in place.
- Attach part A to the overflow pipe and part B to the waste outlet.
- Extend part C fully down and then push the assembly into the waste body until it clicks into position. This will automatically adjust the water seal level.
- The outlet can be rotated as needed to align with the plumbing.
- If the bath is thicker than 7mm, use the extension kit (HC2650-EXT-KIT) to extend the length of the waste outlet and overflow pipe.
- Insert the extension piece (part 3) between parts A and B and secure it in place.
- Insert the sleeve (part 4a) into the waste body (part 4aiii or 4biii) and secure it in place using the hand-tightening tool provided.
- Attach part A to the overflow pipe and part B to the waste outlet.
- Extend part C fully down and then push the assembly into the waste body until it clicks into position. This will automatically adjust the water seal level.
- The outlet can be rotated as needed to align with the plumbing.
Installation Instructions for
HC2650UK
113mm high 1 ½” Bath Trap with Overflow & Clicker Waste Plug & 50mm Seal
Extension Kit available for use in thicker Baths CODE
HC2650-EXT-KIT ****
OUTLET CAN BE ROTATED
Part No. Description
1 Bath Trap Overflow Sub-assembly
a Slim Bathrose
b 61mm Long Ferrule
c Plastic Bag (Not Shown)
d Ø73mm Overflow Cover
e Ø75x52x6.5mm Nitrile Rubber Seal
f S.S. M6 Hex Nut
g Ø73mm S.S. Grid
h Spanner for O/F (Item 1b)
j Shower Spanner (Item 19)
2 750mm Expanding Pipe
3 Clicker Body Sub-assembly
a Seal for Clicker Body
b Clicker Body with O/F
4 Tube and Plug Sub-Assembly
a Tube Sub-Assembly
i ¼ UNC x 7mm Insert
ii 37mm ID x1.5mm O-Ring
iii 28mm ID x 1mm O-Ring
iv 2-Part Shower Trap Tube
b CP Brass Clicker Plug
i Spacer for Clicker Switch
ii Clicker Switch
iii Clicker Seal
iv Ø73mm S.S. Clicker Cover
5 Leaflet (Not Shown)
6 Plastic Bag (Not Shown)
7 Carton (Not Shown)
8 Carton (Not Shown)
9 Ø75x52x6.5mm Nitrile Rubber Seal
10 1 ½” Plastic Washer
11 TPE Seal
12 1 ½” Rubber Multifit Olive13 1 ¼” Nitrile Rubber Seal
14 1 ¼” Compression Nut
15 Ø70mm Flange –No Grating16 Push Fit Flex Adaptor
17 1 ½” Multifit Compression Nut
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>