JOOVV 3.0 Red Light Therapy System User Guide

Door Mount System
Assembly Guide

Warnings and Safety

Please review the following safety information prior to assembling your Joovv Door Mount System. Attempting to assemble and use this equipment without fully understanding its features and functions may result in unsafe operating conditions. Some Warnings and Cautions are also inserted within the manual where they are most meaningful. Notes are also located throughout the manual to provide additional information related to specific features. If you have a question regarding the installation, set up, operation, or maintenance, please contact Joovv Inc. at help@joovv.com.
WARNINGS identify conditions or practices that could result in serious adverse reactions or potential safety hazards.
CAUTIONS identify conditions or practices that could result in damage to the device or other equipment.
Warnings

• No modification of this system is allowed.
• System is only meant to support applicable Joovv products.

Cautions

• Read user manual prior to use and keep for future reference.
• Choking Hazard, small parts. Keep away from small Children.
• For interior use only, storage or installation of the system in direct sunlight may cause the system to yellow or break down over time. Normal storage or installation in window-lit rooms is acceptable.
• Do not leave the system in any place that could be damaged by children, pets, pests, or liquids. If you suspect your system of devices is damaged, contact customer service at Help@Joovv.com.
• Do not install system near heated surfaces such as nearby fireplaces or ceramic heaters.
• Do not install or store system in humid or wet locations such as a sauna or wet sauna.
• Remove the device before adjusting height of Slider Pole Mount.
• When loosening the adjustment knob, do not exceed more than 1.5 turns counterclockwise to loosen. Additional turns can cause the Slider Pole Mount to fall.
• Do not install more than 2 systems on a single door frame.
• Make sure top and bottom door hooks are securely attached prior to mounting devices.
• Do not use power tools to assembly parts in this kit.

Safety Standards

Conforms To: IEC 62471, 60601-2-57, 60601-1-11, 60601-1-6 & AAMI STD ES60601-1
Certified To: CSA STD C22.2 #60601-1

Parts List

1 Pole Kit

Door Configurations

Half Max configuration
Duo configuration

Max configuration
Quad configuration

1 Pole Setup

Step 1 – Connect Pole Upright
Connect the Top and Bottom sections of the Pole Upright by inserting the Top section into the coupler portion of the Bottom section and securely fastening using the M4 screw (H) as shown.
Note, over tightening the M4 screw (H) can make it difficult for the Slider Mount to pass through the coupler section of the Pole Upright.
When initially installing the Slider Mount keep the M4 screws (H) semi tight to allow the Pole Uprights to flex slightly. After positioning the Slider Mount to the dedicated height, the M4 screws can be fully tightened.
Step 2
Install the Slider Mount(s) attachment to Pole Upright. Turn knob counterclockwise ~1 turn and pullout to slide on the pole.

Step 3
Connect top and bottom assembly to Pole Upright using M6 Screw with Allen Key.

WARNING!
Do not use power tools to assembly parts in this kit.
Step 4
Install Door system on door as shown in the illustration below.

Step 5
To secure the Bottom Assembly hook to the door, pull the strap through the buckle to tighten. Once pulled tight, roll up the excess strap and hide using the Cover Cap.

For easier access keep strap loose until device, AC power cable(s) and spacers are installed.
Step 6
To adjust the Slider Mount, turn the knob counterclockwise ~1 turn and pull out. Slide the mount up or down based on your desired height. To secure the Slider Mount tighten the knob by turning it clockwise until hand tight.

WARNING!
When loosening the adjustment knob, do not exceed more than 1.5 turns counterclockwise to loosen.
Additional turns can cause the Slider Pole Mount to fall.
Step 7
While holding the device as shown below, align the device over the Slider Mount keyholes and slide the device down onto the Slider Mount to secure.

Step 8
To remove the Solo or Mini Device from the Slider Mount, follow the steps illustrated below.
TO MOVE LOCATION OF A SOLO OR MINI UNIT ON THE DOOR MOUNT:

2 Pole Setup
To configure a 2 Pole Setup, repeat steps found on page [8] for the 1 Pole Setup.
After completing your setup and installing your devices, refer to page [18] for installing the alignment plugs.

Reference the Mini & Solo User Manual for wire diagram and cable installation.

Setting Slider Mount on Pole for Specific Configurations

For the Duo and Half Max configuration set the top Slider Mount so 11 holes are showing from the top of the Pole Upright.

For the Duo configuration set the bottom Slider Mount so 5 holes are showing from the bottom of the Pole Upright.
For the Half Max set the bottom Slider Mount at 17 holes from the bottom.
Note: the Solo will be the bottom device.

Oversize Door Options & Installation

For doors that are taller than 84’’ up to 96’’ and thicker than 1- 3/8’’ up to 1 3/4’’ Joovv offers an Oversize Door Kit that can be purchased at Joovv.com. To install Oversized Door Hook, follow instructions illustrated below.

1. Remove top Door Hook from Bracket Arm and replace with Oversized Door Hook.
2. For doors that are taller than 84” up to 96”, remove and replace the Bracket Arm with Oversized Arm.
3. For the bottom Door Hook, remove the strap from the buckle, and install the Oversized Door Hook.

Adding Spacers to Mounted Devices

Spacers help keep the separate devices aligned and immobile. See illustration below for Spacer insert locations.

When using the spacer kit with the Joovv Mini, utilize the included O-Rings with your spacer kit before inserting.
Slide the O-Ring onto the spacer plug

Revision History

Date| Revision #| Description of Changes
November-20| JV-MKT-DOC-2804 (Ver.0)| Ver.0 Release to market
June-21| JV-MKT-DOC-2804 (Vert)| Addition to pages 2, 4, 6,12 – New Pole Kit
March-22| JV-MKT-DOC-2804 (Ver.2)| Addition to page 8

Warranty

All Joovv mounting accessories are covered by a 2-year limited warranty. Please visit our website at
https://joovv.com/pages/warranty for details of the limited warranty. To register your product, visit
https://joovv.com/pages/warranty for instructions. Failure to register will not affect your limited
warranty rights.
Return Policy
All mounting accessories come with a 60-day return period. If you’re not satisfied with your purchase within the first 60 days, please visit our website at https://joovv.com/pages/returns for additional details.
Contact Information

Joovv, Inc.
940 Calle Amanecer, Suite D,
San Clemente, CA 92673, USA.
Email us: help@joovv.com
Website: www.joovv.com
Online Setup instructions: www.joovv.com/setup
joovv.com
JV-MKT-DOC-2804 VER.2

References

• Red and Infrared LED Light Therapy Devices | Joovv
• Red and Infrared LED Light Therapy Devices | Joovv
• Set Up Your Joovv 3.0 Red Light Therapy System
• Learn About Joovv's 30-60-Day Return Policy
• Joovv Red Light Therapy Limited Warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>