Hunter 99370 Ceiling Fan Remote Control User Manual
- October 30, 2023
- Hunter
Table of Contents
Hunter 99370 Ceiling Fan Remote Control
HUNTER FAN COMPANY CONTROL LIMITED WARRANTY
The Hunter Fan Company provides a limited warranty to the original purchaser of the Control (Control). The Control is warranted to be free from defects in material and workmanship for a period of one year from the date of purchase. For more information, please refer to the user manual. This product conforms to UL Standard 1917.
WARNINGS
This device complies with part 15 of the FCC Rules and RSS-210 of Industry
Canada. Operation is subject to certain conditions. For more information,
please refer to the user manual.
If you are installing multiple remote-controlled fans on the same circuit
breaker, you may need to perform a few extra steps to prevent interference or
faulty operation of your remote controls. For more information, please visit
www.HunterFan.com/FAQs and click How do I properly
install multiple remote-controlled fans?
Installation
- Turning off the power: Before installation, use the pull chains to set the fan speed to HIGH and the light to ON. Ensure the power is OFF at the outlet box and wall switch location before proceeding with installation.
- Removing the canopy: Remove the canopy. If uncertain how to remove it, reference the fan’s owner’s manual. With wiring exposed, it may be helpful to note existing wire connections or take a digital photo for reference. Remove the wire connectors that connect the wires from the outlet box to the fan, leaving the grounding wires connected.
- Installing the receiver: Choose the hanging system that most closely resembles the one used by your fan, and install the receiver and wire as directed. You may have installation issues if the fan is installed on an angled ceiling. For assistance, call 1-888-830-1326.
- Wiring the receiver and fan to the ceiling: Using the orange from the receiver and the white wire from the fan. After all wires are connected and secured with wire connectors, re-install the canopy.
Note: Some fans may have considerable excess lead wire. For easier canopy installation, use a cable tie to bundle and secure excess lead wire.
IMPORTANT WARNING
To avoid possible electrical shock, before installing your fan, disconnect
the power by turning off the circuit breakers to the outlet box associated
with the wall switch location.
CEILING FAN REMOTE CONTROL Model 99370, 99394
HUNTER FAN COMPANY CONTROL LIMITED WARRANTY
The Hunter Fan Company makes the following limited warranty to the original purchaser of the Control (“Control”): Your Control is warranted to be free from defects in material and workmanship for a period of one year from the date of sale. If the Control malfunctions or fails within the warranty period due to a defect in material or workmanship we will replace it free of charge. IF THE ORIGINAL PURCHASER CEASES TO OWN THE CONTROL, THIS WARRANTY AND ANY IMPLIED WARRANTY, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE VOIDED. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IN RESPECT TO ANY CONTROL, IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH CONTROL. This warranty excludes malfunctions or failures which were caused by repairs by persons not authorized by us, mishandling, improper installation, modifications, or damage to the Control while in your possession, or unreasonable use. This warranty does not apply to batteries or to deterioration or damage to the product caused by the use of faulty batteries. To obtain a replacement, return your Control postage prepaid along with proof of purchase to Hunter Fan Company Service Department at 7130 Goodlett Farms Pkwy., Memphis, TN 38016. IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Read and Save These Instructions
This product conforms to UL Standard 1917.
WARNINGS
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna,
- Increase the separation between the equipment and receiver,
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Note: Any changes or modifications to the transmitter or receiver not
expressly approved by Hunter Fan Company may void one’s authority to operate
this remote control. Chemical burn hazard. Keep batteries away from children.
This remote contains a lithium button cell battery. If a new or used lithium
button/coin cell battery is swallowed or enters the body, it can cause severe
internal burns and can lead to death in as little as 2 hours. Always
completely secure the battery compartment. If the battery compartment does not
close securely, stop using the product, remove the batteries, and keep it away
from children. If you think batteries might have been swallowed or placed
inside any part of the body, seek immediate medical attention. Dispose of
cells properly and keep away from children. Even used cells may cause injury.
If you are installing multiple remote-controlled fans on the same circuit
breaker, you may need to perform a few extra steps to prevent interference or
faulty operation of your remote controls.
Go to www.HunterFan.com/FAQs and click “How
do I properly install multiple remote-controlled fans?” for more information.
Installation
Turning off the power
Before installation, use the pull chains to set the fan speed to HIGH and the
light to ON. Ensure the power is OFF at the outlet box and wall switch
location before proceeding with installation.
Removing the canopy
Remove the canopy. If uncertain how to remove it, reference the fan’s owner’s
manual. With wiring exposed, it may be helpful to note existing wire
connections or take a digital photo for reference. Remove the wire connectors
that connect the wires from the outlet box to the fan, leaving the grounding
wires connected.
Installing the receiver
Choose the hanging system that most closely resembles the one used by your
fan, and install the receiver and wire as directed.
You may have installation issues if the fan is installed on an angled ceiling.
For assistance, call 1-888-830-1326.
WARNING
To avoid possible electrical shock, before installing your fan, disconnect the
power by turning off the circuit breakers to the outlet box associated with
the wall switch location.
Note: Some fans may have considerable excess lead wire. For easier canopy installation, cut the excess wire, leaving a minimum of 8” remaining. Re-strip the fan lead wires 1/2”. Place remaining excess wire into the ceiling electrical box. The bracket and fan must remain properly grounded.
Wiring the receiver to the fan
Using the orange wire connectors, connect the blue wire from the receiver to
the blue wire (or possibly black with white stripe wire) from the fan. Connect
the yellow wire from the receiver to the black wire from the fan.
WARNING
All wiring must be in accordance with national and local electrical codes
ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a
qualified electrician.
Note: If you are uncertain about wire colors or connections, please contact a qualified electrician.
Wiring the receiver and fan to the ceiling
Using the orange wire connectors, connect the black wire (ungrounded) from the
ceiling to the black wire from the receiver. Connect the white wire (grounded)
from the ceiling to both the white wire from the receiver and the white wire
from the fan.
AFTER ALL WIRES ARE CONNECTED and secured with wire connectors, re-install the canopy.
Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box.
Installing the battery
To access the battery compartment, remove the small Phillips head screw that
secures the battery door to the remote control.
Replace the used battery with a CR2032 battery when necessary. The battery
should be installed with the positive (+) side up.
Turning on the power
Use the pull-chain switch on the fan to set the fan speed to the HIGH position
before operation.
Reference the included remote function card for information on how to use your
control!
The remote transmitter is already paired to the receiver and ready to use.
Note: If your need to pair your remote, cycle power to the fan by turning
power off and back on at the wall switch (or circuit breaker if necessary).
Within three minutes, press and hold both the Fan button and the Light button
for four seconds to pair the remote.
To prevent faulty operation, please disconnect power from all other ceiling
fans within range while pairing.
Remote Function Guide
Key Press: Function
- Light On/Off
- Light Dimming
- Fan On/Off
- Dimming Mode On/Off
M0122 • 2/28/20 • © 2020 Hunter Fan Company
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>