CP PLUS CP-L23-WiFi Smart WiFi Battery Doorbell User Manual

CP PLUS CP-L23-WiFi Smart WiFi Battery Doorbell

Product Information

The product is a Doorbell with the following features:

• SD Card Slot
• USB Port
• DC 12V/1A
• Built-in Siren
• Ring button
• Allows to detect human movement
• Controlled by Mobile APP
• Rain cover included

Product Usage Instructions

To use the Doorbell, follow these instructions:

1. Plug in the supplied power adaptor to the DC 12V/1A port.
2. Insert an SD Card into the SD Card Slot to add storage to the Doorbell.
3. Press the Ring button to activate the Doorbell, which can detect human movement.
4. If the Doorbell battery is completely drained, charge it with a Micro USB cable using a 5v 2amp adaptor.
5. Control the Doorbell using the Mobile APP.
6. If you plan to use the Doorbell outdoors, use the included rain cover to protect it from the elements.

Main features

Packing List

Open the package and make sure the Smart wifi battery doorbell (device) is intact, and with all the below accessories.

Product Component

Component : Description

• Microphone : Transfer the sound
• Lens : Capture Videos
• Light Sensor : Infrared Light Adjustment
• Motion sensor(PIR) : Allows to detect human movement
• Infrared LED : Additional Light in Low-light Conditions
• Ring button : You will receive notification or call by the App when its pressed.
• Indicator light : Status indicator light which shows the device’s working status.
• Speaker  : Audio channel

Component : Description

• Power Switch : Power OFF/ON
• Reset : By pressing the reset button on the back of the device for more than 3 seconds, you will hear a sound and see the indicator light blinks red. (Be advised that all your data on the device will be reset to default)
• SD Card Slot : Use SD Card to add storage to Doorbell
• USB Port : Once your Doorbell battery is completely drained then you need to charge battery with Micro USB cable using 5v 2amp adaptor
• Built-in Siren : Controlled by Mobile APP
• CE Label : Product label

 Preparation

One smartphone or tablet PC with IOS 9.0 or Android 4.4 operating system or higher (This model does not work with a Mac or Windows PC)

Wi-Fi Router

• This device does not support 5.0Ghz and will only connect to a 2.4Ghz WiFi router

• Open the waterproof cover on the side of the device and insert the TF card into card slot.

• Switch it from [OFF] to [ON], and press the reset buttons.

• If you see the red indicator light blinking, then the operation has already begun.

LED Light State Introductions

Set up APP& Configure Device

Search and download’ Ezykam+” in major application markets or scan the QR code below to download the APP.

Once you download the APP to your smart phone, you may enter the first page which you can Login with existing account or Register. If you are the new user of Ezykam+ and don’t have an account, please choose register first and follow the below screenshots to complete the registration.

(If you have the existing account, there are two ways to login, one is with SMS verification Code, the other one is with password. In case you forget the password, you may choose login SMS verification Code or you can choose forgot password to reset it by Entering Verification Code which sent to you mobile via message. )

Once the account has been setup successfully, then you will automatically enter the page of “Add Device”, kindly follow below steps to add the camera.

• Step1: click “Add Device “or click “+ “on top of right on this page.

• Step2: Choose Smart Home > Home Security > Door bell and follow the snapshot below

• Step3: You may choose next stop to go to QR code paring mode or you may go to “other Mode” on top of right to enter the page of choosing QR Code Net-pairing or Smart configuration, if you choose the “next step” you may follow the below screenshots:

• Step4: If you choose ” the other mode ” on the top of the right side, you may find QR Code Net-pairing Which you will go back to the “Add Device page and process it again like above procedure. Or you can choose “Smart configuration” and follow the below screenshots and after that you will see the device added successfully.

How to mount your doorbell

Method 1: Attaching to a smooth wall surface

• Stick the double-sided 3M stickers on the bracket (rain cover).

• Tear off the protective film on the 3M stickers, apply it on a smooth wall surface at the appropriate height. Hang the device on the bracket from top down lining up the hole at back of device. Tighten the screw on the bottom of the unit to the bracket.

Method 2: If you want install the device on a rough wall (such as concrete, brick or a wooden surface), use screws to fix the bracket.

• Set the bracket on wall according to required height by screws.

• Hang the device on the bracket from top down lining up the hole at back of device. Tighten the screw on the bottom of the unit to the bracket.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>