Swifty Scooters SwiftyONE MK4 Electric Kick Scooter Instruction Manual
- October 30, 2023
- Swifty Scooters
Table of Contents
Swifty Scooters SwiftyONE MK4 Electric Kick Scooter
Product Information
The SwiftyONE-e is a foldable electric scooter that comes with a user manual, a battery charger, and a Lezyne Rear Light. The scooter has a folding stem adjuster, a carry handle, and a footplate toggle. The handlebars have a quick- release mechanism, and the rear fork has a tab that needs to be flicked in to unfold the scooter. The SwiftyONE-e scooter comes with tools required to reassemble parts that may have been disassembled for packing purposes. The scooter’s tires need to be inflated with a pump that has a standard Schrader valve, and the recommended tire pressure is 60-80 PSI.
Product Usage
- Read the User Manual, observe rider restrictions and read the returns policy and warranty overleaf before unpacking the scooter.
- Unpack the scooter carefully and keep all packaging until you are entirely satisfied with your purchase.
- Follow the steps illustrated below to unfold your scooter and prepare for your first ride.
- Turn footplate toggle, and lift folding stem.
- Secure folding stem lever with toggle.
- Release handlebar quick release.
- Rotate and lower handlebars, and tighten quick release. Ensure that the MIN.INSERT level markings are observed for the highest handlebar height, and they are not visible.
- Flick in tab on rear fork to unfold. Keep fingers inside carry handle when folding and unfolding to avoid finger trap.
- Hold carry handle and lift up to rotate the wheel through the Folding stem adjuster.
- Pull back pin and release to lock rear fork into place.
- Lower footplate.
- Inflate tires with a pump that has a standard Schrader valve. See tire for max. PSI. Recommended tire pressure is 60-80 PSI.
- Perform a basic safety check before each ride as described in the User Manual. Check brakes are working. Check bolts, wheel nuts, and quick-release levers are tightened fully. Adjust the position of handlebars or brake levers using the tool provided if required.
- If you face any problems, contact your local dealer, or contact SwiftyHQ at Tel: +44 (0)161 848 8695 or email: [email protected]
- If you are not entirely satisfied with your purchase, refer to the returns policy mentioned in the User Manual.
HOW TO UNFOLD
Before unpacking your scooter, you must read the User Manual, observe rider restrictions and read the returns policy and warranty overleaf. Take care when unpacking your scooter, please keep all packaging until you are entirely satisfied with your purchase.Follow the steps illustrated below to unfold your scooter and prepare for your first ride. Some parts may vary from the diagram, however the (un)folding process remains the same. You will need a pump with a standard ‘Schrader’ valve when inflating the tyres. Please observe our safety recommendations in the User Manual before your first ride. Please note, a part of the scooter may have been disassembled by our packing team in order to fit accessories in the box (e.g. mudguards, kick-stand) you will find the tools required to reassemble these parts enclosed. We have prepared video tutorials for you to watch on our YouTube channel. Go to swiftyscooters.com/assembly- guides to find the direct links to our videos. If you have any problems, please contact your local dealer, or contact us: SwiftyHQ Tel: +44 (0)161 848 8695 Email: [email protected]
- Turn footplate toggle, and lift folding stem
- Secure folding stem lever with toggle
Inflate tyres – you will need a pump with standard Schrader valve. See tyre for max. PSI. Recommended tyre pressure 60-80 PSI.
Perform a basic safety check before each ride as described in the User Manual. Check brakes are working. Check bolts, wheel nuts and quick release levers are tightened fully. You may wish to adjust the position of the handlebars or brake levers, using the tool provided.
POWER IT UP
Your scooter should now be unfolded and ready to go. You can now take the following steps to give electric power to your Swifty. These are the basic steps to get you started, please read the Swifty e-scooter User Manual in full before you start your first journey. If you have any problems, please contact your local dealer, or contact us: SwiftyHQ Tel: +44 (0)161 848 8695 Email: [email protected]
-
Your e-scooter battery will arrive partially charged. We recommend charging before your first ride
-
You can charge your battery whether it’s on or off the scooter. To take your battery off the scooter, you’ll first need to unlock the battery with the keys provided.
WARNING!
You are supplied with 2 keys to secure the battery. It is advisable to separate the keys and keep the spare in a safe place. -
After the battery is unlocked, slide it to the side to release it from the bracket. Be careful not to force it.
How to Charge:
- Plug your charger into a mains socket, the LED light on the charger will illuminate GREEN
- Peel open the yellow cover on the side of the battery. Connect the charger to the battery using the lead provided, the LED light on the charger will then change to RED which indicates its charging.
- A full charge takes up to 6 hours. To prolong the life of the battery, charge it after every trip.
- Once fully charged the LED light on the charger will switch back to GREEN, indicating the battery is fully charged.
TIME TO RIDE
If you have any problems, please contact your local dealer, 3 or contact us:
SwiftyHQ Tel: +44 (0)161 848 8695 Email: [email protected]
DISPLAY INTERFACE DIAGRAM
- Long press the middle button next to the throttle LCD display for 2 seconds – the display interface should light up.
- To turn on your headlight, short press the middle button , the icon should appear on the top right of the display interface. You should also turn on your rear light manually to increase your visibility.
- Press the M button to switch among the 4 acceleration modes.
- Kick scooter mode, motor will not start
- Slow acceleration, for inexperienced new riders
- Medium acceleration, for a balanced riding experience
- Max acceleration, for maximum torque and scooting uphill
To set off, take the following steps:
- Place one foot on the footplate and push off with your other leg. Balance both feet on the scooter when you have enough momentum.
- After you’ve pushed off, twist the grip throttle towards you gently to start the motor.
- Hold the throttle halfway to maintain the desired speed.
- Twist the throttle all the way to get the maximum speed of 25 km/h or 15.5 mph.
To stop – Always release throttle before applying brakes.
- To perform an emergency stop, release throttle, bend knees, brace arms and use both brakes together, keeping both feet firmly on the footplate as you come to a stop.
- Scan me for video guides of assembly and maintenance! or go to swiftyscooters.com/assembly-guides
KICK-STAND
If you have any problems, please contact your local dealer, or contact us:
- SwiftyHQ Tel: +44 (0)161 848 8695
- Email: [email protected]
HOW TO USE
- Flip both legs out to the side.
- Using your toe to pivot the kickstand down to the ground, roll the scooter backward until the kickstand snaps into place underneath the rear wheel.
- The final standing position, the rear wheel is lifted, with the stand underneath. When you’re
HOW TO FOLD THE REAR WHEEL
- When you’re ready, fold the kickstand down with the legs closed as shown above.
- Lift the footplate and rotate the rear wheel.
- The kickstand will rotate through the frame into the fully folded position as shown above.
References
- Big Wheel Adult Scooter, Kids and Electric scooters – Swifty Scooters
- Scooter Assembly Guides | Swifty Scooters
- Warranty | Swifty Scooters
- Warranty | Swifty Scooters