beko EV 6102 Washing Machine Instruction Manual
- October 30, 2023
- Beko
Table of Contents
EV 6102 Washing Machine
Product Information: EV 6102
The EV 6102 is a washing machine that is designed for home use.
It has a loading door and a drum that can hold a full load of
laundry. The product requires electricity, tap water, and a water
drainage system to operate. The product is equipped with safety
features to prevent personal injury and property damage. The
product must be installed by an Authorized Service Agent to ensure
proper grounding and installation.
Important Safety Instructions
-
Place the product away from the reach of children.
-
Ensure that the product is grounded in accordance with local
regulations. -
Do not neglect to have the grounding installation made by a
qualified electrician. -
Do not open the loading door or remove the filter while there
is still water in the drum. -
Make sure that the water inlet and discharge hoses as well as
the power cable are not folded, pinched or crushed while pushing
the product into its place after installation or cleaning
procedures.
Installation
The installation of the product must be carried out by an
Authorized Service Agent. The customer is responsible for preparing
the location and electrical, tap water and waste water
installations at the place of installation. The product must be
securely fastened and remain undamaged to prevent water leakage.
The loading door will be ready to open just a few minutes after the
washing cycle comes to an end. Do not force the loading door to
open.
Removing Packaging Reinforcement
To remove the packaging reinforcement, tilt the machine
backwards and remove the packaging reinforcement by pulling the
ribbon.
Removing Transportation Locks
Before operating the washing machine, remove the transportation
safety bolts. Loosen all the bolts with a suitable spanner until
they rotate freely and remove transportation safety bolts by
turning them gently. Attach the plastic covers supplied in the User
Manual bag into the holes on the rear panel.
Product Usage Instructions: EV 6102
-
Prepare the location and electrical, tap water and waste water
installations at the place of installation. Make sure that the
product is securely fastened and remains undamaged to prevent water
leakage. -
Ensure that the product is grounded in accordance with local
regulations. Do not neglect to have the grounding installation made
by a qualified electrician. -
Remove the packaging reinforcement by tilting the machine
backwards and pulling the ribbon. -
Remove the transportation safety bolts before operating the
washing machine. Loosen all the bolts with a suitable spanner until
they rotate freely and remove transportation safety bolts by
turning them gently. Attach the plastic covers supplied in the User
Manual bag into the holes on the rear panel. -
Place the laundry into the drum of the washing machine.
-
Add detergent to the detergent compartment.
-
Select the desired washing cycle and options according to the
laundry type and level of soil. Refer to the user manual for
detailed instructions on selecting cycles and options. -
Press the start button to begin the washing cycle. The loading
door will be ready to open just a few minutes after the washing
cycle comes to an end. Do not force the loading door to open. -
After the washing cycle is complete, remove the laundry from
the drum and close the loading door.
Washing Machine Pln automatická pracka Automatická pracka Pralka automatyczna
EV 6102
1 – EN
1 Important safety instructions
This section contains safety instructions that will help protect from risk of
personal injury or property damage. Failure to follow these instructions shall
void any warranty.
General safety
· This product should not be used by persons with physical, sensory or mental
disorders or unlearned or inexperienced people (including children) unless
they are attended by a person who will be responsible for their safety or who
will instruct them accordingly for use of the product.
· Never place the product on a carpet-covered floor; Otherwise, lack of
airflow beneath the machine will cause electrical parts to overheat. This will
cause problems with your product.
· Do not operate the product if the power cable / plug is damaged. Call the
Authorized Service Agent.
· Have a qualified electrician connect a
on the detergent package. · The product must be unplugged during
installation, maintenance, cleaning and repairing procedures. · Always have
the installation and repairing procedures carried out by the Authorized
Service Agent. Manufacturer shall not be held liable for damages that may
arise from procedures carried out by unauthorized persons.
Intended use
· This product has been designed for domestic use. It is not suitable for
commercial use and it must not be used out of its intended use.
· The product must only be used for washing and rinsing of laundry that are
marked accordingly.
· The manufacturer waives any responsibility arisen from incorrect usage or
transportation.
Children’s safety
· Electrical products are dangerous for the
16-Ampere fuse to the installation location of the product. · If the product has a failure, it should not be operated unless it is repaired by the Authorized
children. Keep children away from the product when it is in use. Do not let them to tamper with the product. · Do not forget to close the loading door when
Service Agent. There is the risk of electric shock! · This product is designed to resume operating
leaving the room where the product is located. · Store all detergents and
additives in a safe
place away from the reach of the children.
in the event of powering on after a power
interruption. If you wish to cancel the programme, see “Cancelling the programme”
2 Installation
section.
Refer to the nearest Authorised Service Agent for
· Connect the product to a grounded outlet
installation of the product. To make the product
protected by a fuse complying with the values ready for use, review the information in the user
in the “Technical specifications” table. Do not
manual and make sure that the electricity, tap water
neglect to have the grounding installation made by a qualified electrician. Our company shall not be liable for any damages that will arise
supply and water drainage systems are appropriate before calling the Authorized Service Agent. If they are not, call a qualified technician and plumber to
when the product is used without grounding in have any necessary arrangements carried out.
accordance with the local regulations.
C Preparation of the location and electrical, tap
· The water supply and draining hoses must be
water and waste water installations at the place
·
securely fastened and remain undamaged. Otherwise, there is the risk of water leakage. Never open the loading door or remove the filter
of installation is under customer’s responsibility.
B
Installation and electrical product must be carried
connections of the out by the Authorized
while there is still water in the drum. Otherwise, risk of flooding and injury from hot water will occur.
Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized
· Do not force open the locked loading door.
persons.
The loading door will be ready to open just a few minutes after the washing cycle comes to
A
Prior to installation, has any defects on
visually it. If so,
check if the product do not have it
an end. In case of forcing the loading door to
installed. Damaged products cause risks for
open, the door and the lock mechanism may get damaged. · Unplug the product when not in use. · Never wash the product by spreading or
your safety.
C
Make sure that the water inlet and discharge hoses as well as the power cable are not
folded, pinched or crushed while pushing
pouring water onto it! There is the risk of electric
the product into its place after installation or
shock!
cleaning procedures.
· Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out
Appropriate installation location
· Place the machine on a rigid floor. Do not place
by grabbing the plug. · Use detergents, softeners and supplements
it on a long pile rug or similar surfaces. · Total weight of the washing machine and the
suitable for automatic washing machines only. · Follow the instructions on the textile tags and
dryer -with full load- when they are placed on top of each other reaches to approx. 180
2 – EN
kilograms. Place the product on a solid and flat floor that has sufficient
load carrying capacity! · Do not place the product on the power cable. · Do
not install the product at places where temperature may fall below 0ºC. ·
Place the product at least 1 cm away from the edges of other furniture.
Removing packaging reinforcement
Tilt the machine backwards to remove the packaging reinforcement. Remove the
packaging reinforcement by pulling the ribbon.
Removing the transportation locks
A Do not remove the transportation locks before
taking out the packaging reinforcement.
A Remove the transportation safety bolts before
operating the washing machine! Otherwise, the product will be damaged. Loosen
all the bolts with a suitable spanner until they rotate freely (C). Remove
transportation safety bolts by turning them gently. Attach the plastic covers
supplied in the User Manual bag into the holes on the rear panel. (P)
C Keep the transportation safety bolts in a safe
place to reuse when the washing machine needs to be moved again in the future.
C
Never move the product without the transportation safety bolts properly fixed in
place!
Connecting water supply
C
The water supply pressure required to run the product is between 1 to 10 bars (0.1 10
MPa). It is necessary to have 10 80 liters of
water flowing from the fully open tap in one
minute to have your machine run smoothly.
Attach a pressure reducing valve if water
pressure is higher.
C If you are going to use the double water-inlet
product as a single (cold) water-inlet unit, you
must install the supplied stopper to the hot water valve before operating the product. (Applies for the products supplied with a blind
stopper group.)
C If you want to use both water inlets of the
product, connect the hot water hose after
removing the stopper and gasket group from
the hot water valve. (Applies for the products
supplied with a blind stopper group.)
A
Models with a single water inlet should not be connected to the hot water tap. In such a case
the laundry will get damaged or the product will
switch to protection mode and will not operate.
A
Do the
not use old or new product.
used water inlet hoses It may cause stains on
on your
laundry.
1. Connect the special hoses supplied with the
product to the water inlets on the product. Red hose (left) (max. 90 ºC) is for hot water inlet,
blue hose (right) (max. 25 ºC) is for cold water
inlet.
A Ensure that the cold and hot water connections
are made correctly when installing the product. Otherwise, your laundry will
come out hot at the end of the washing process and wear out. Tighten all hose
nuts by hand. Never use a wrench when tightening the nuts. Open the taps
completely after making the hose connection to check for water leaks at the
connection points. If any leaks occur, turn off the tap and remove the nut.
Retighten the nut carefully after checking the seal. To prevent water leakages
and damages caused by them, keep the taps closed when the machine is not in
use.
Connecting to the drain
· The end of the drain hose must be directly connected to the wastewater drain
or to the washbasin.
A Your house will be flooded if the hose comes
out of its housing during water discharge. Moreover, there is risk of scalding
due to high washing temperatures! To prevent such situations and to ensure
smooth water intake and discharge of the machine, fix the end of the discharge
hose tightly so that it cannot come out. · The hose should be attached to a
height of at least 40 cm, and 100 cm at most. · In case the hose is elevated
after laying it on the floor level or close to the ground (less than 40 cm
above the ground), water discharge becomes more difficult and the laundry may
come out excessively wet. Therefore, follow the heights described in the
figure.
· To prevent flowing of dirty water back into the machine and to allow for
easy discharge, do not immerse the hose end into the dirty water or do not
drive it in the drain more than 15 cm. If it is too long, cut it short.
· The end of the hose should not be bent, it should not be stepped on and the
hose must not be pinched between the drain and the machine.
· If the length of the hose is too short, use it by adding an original
extension hose. Length of the hose may not be longer than 3.2 m.
3 – EN
Obsah je uzamcen
Dokoncete, prosím, proces objednávky. Následn budete mít pístup k celému
dokumentu.
Proc je dokument uzamcen? Nahnvat Vás rozhodn nechceme. Jsou k tomu dva hlavní
dvody: 1) Vytvoit a udrzovat obsáhlou databázi návod stojí nejen spoustu úsilí
a casu, ale i financní prostedky.
Dlali byste to Vy zadarmo? Ne. Zakoupením této sluzby obdrzíte úplný návod a
podpoíte provoz a rozvoj nasich stránek. Teba se Vám to bude jest nkdy hodit.
) Mozná zpocátku ano. Ale vzte, ze dotovat to dlouhodob nelze. A rozhodn na
tom nezbohatneme. 2) Pak jsou tady ,,roboti”, kteí se pizivují na nasí práci a
,,vysávají” výsledky naseho úsilí pro svj prospch. Tímto krokem se jim to
snazíme pekazit. A pokud nemáte zájem, respektujeme to. Urgujte svého
prodejce. A kdyz neuspjete, rádi Vás uvidíme!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>