BOSCH SMV50M00EU Fully Integrated Dishwasher Instructions

Quick reference guide Dishwasher

Before using the first lime, read the operating instructions!

Adjusting the water softening system *

Ask your water supply company what the water hardness is and enter …
• only before the first wash or if the water hardness has been changed

How to adjust

• Switch on ON/OFF switch.
• Hold down program button A and press the START button until H:0 … is indicated on the digital display.
• Release both buttons. The LED for button A flashes and the factory set value of H:04 is indicated on the digital display.
• Press program button C. Each time the button is pressed the set value increases by one setting; when the value reaches H:07, the display jumps back to H:00 (off).
• Press the START button. The chosen setting has now been stored.

Maintenance and care

Fer pertect rinsing results …

| |
---|---|---
Filters … check, if required, clean.Rotate
filter cylinder, remove filter system …| rinse under running water …| insert …
| |
Screw on filter system NOTE MARK!| spray arms Renove blockages/ deposits.pull lower arm upwards …| unscrew upper arm …
| |
clean spray nozzies under running water (if required use toothpicks)…| insert lower arm … screw on upper arm tightly| … QS il @ werth doing it yourself! Mere information can be found in the operating  instructions

Cleaning eater water pum
– Pull out the mains plug.
– Remove filters and scoop out water.
– Lever off cover (A).
~ Check the area around the fan impeller for foreign objects.
– Click cover shut (B).
– Insert filters.
Rectifying minor faults yourself

| Open supply fitting.
1. Unscrew water connection.
2.Clean filter in the water connection.
3.Flow rate must be min. 10 1/min., when water supply is open.
If the flow rate is less,
replace the supply fitting.
Install supply hose without kinks.
Display “E:22”| Filters are soiled or blocked| Clean the filters (see above).
Display “E:24” and “a” are lit*| The waste water hose is blocked or kinked
Cover not attached to wastewater pump| Install waste water hose without kinks. Attach cover (see above).
Display “E:25” and “a” are lit`| Waste water pump blocked| Clean waste-water pump (see above).
Other fault display “E: XX” is lit| The appliance has a technical defect| Call factory customer service (state fault display).
Residual water in the appliance| The program has not yet ended| Unplug appliance.
Switch on and close the appliance or terminate the program
(see Terminating the program).
Rust on the cutlery| Cutlery not rust-resistant
Hard knife blades are more susceptible
Extraneous rust| Use dishwasher-proof cutlery.
Never wash rusting parts in the appliance.
---|---|---
Fault| Possible causes| Remedial action
---|---|---
Utensils are not clean
Sand or gritty residue on the utensils| Utensils are situated close together or one above the other| Separate the utensils, and prevent contact points.
| Too little detergent
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Spray arms blocked| Follow manufacturer’s instructions (detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Clean the filters (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Stains and streaks| Rinse aid dosage too high/ too low| Streaks: reduce the dosage.
Water or limescale stains: increase the dosage.
---|---|---
Utensils not dry| Rinse aid| Increase dosage.
Change the product.
| The combined detergent used has a poor drying performance
Appliance setting| Use rinse aid.
Activate intensive drying (depending on the model).
Milky deposits on the utensils (can be removed)| The water softening system was incorrectly set
No salt| Correctly set water softening system.
Refill with special salt.
Milky deposits, glasses cloudy/tarnished (cannot be removed)| Glasses not dishwasher-proof| Use dishwasher-proof glasses.
Use a detergent suitable for glasses.
Plastic/utensils discolored| Too little detergent
Discoloration caused by food colorings (tomato sauce)| Follow manufacturer’s instructions (detergent).
The discoloration is harmless; subsequent rinse cycles will cause it to fade.

Terminating the program …

While the program is running, press the START button for approx. 3 sec. (Reset).| The numerical display indicates “0:01”; approx. 1 minute after the program ends, “0:00” is indicated.| Switch off the appliance.
---|---|---

Loading the dishwasher correctly …
Dishwasher-proof utensils (not soiled with ash, wax, lubricating grease, ink or adhesive labels; remove large remnants of jam, milk products and food according to the operating instructions and check that the spray arms can rotate freely.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>