Wemo F7C059 WiFi Smart Dimmer User Guide
- October 30, 2023
- WeMo
Table of Contents
- Wemo F7C059 WiFi Smart Dimmer
- Setup Guide
- Important to know
- What you’ll need
- Recommended tools
- Compatible light bulbs
- Installing your Dimmer
- Identify and label LINE and LOAD wires
- Wire labels
- Help with distinguishing LINE wire from LOAD wire
- Test to identify the wires
- Connect Wemo Dimmer wires
- Connect NEUTRAL and GROUND wires
- Install Dimmer 6 into the wall
- Turn on power
- Go to the app for the next steps
- Connecting to other services
- Got questions
- What does the light tell me
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Wemo F7C059 WiFi Smart Dimmer
Wemo Smart Dimmer
Setup Guide
Important to know
- WARNING! Risk of electric shock: Incorrect installation could be dangerous or illegal. Multiple breakers/fuses may need to be turned off for safe installation. Please call a professional electrician if you are unfamiliar or uncomfortable with electrical work.
- Wemo Smart Dimmer can only replace single-pole switches.
- If your light can be turned on from two different wall switches, that’s a 3-way switch and Wemo Smart Dimmer is not compatible.
- Neutral wires are required for setup. These wires are typically white and can be found in your electrical box.
What you’ll need:
- Cover Plate
- Dimmer and Screws (use the provided screws and don’t over-tighten)
- 4 Wire Nuts
Recommended tools:
- Compatible light bulbs: All incandescent light bulbs are dimmable, but not all LEDs and CFLs are. Go to wemo.com/bulbs for more information.
- Maximum total wattage:
- Incandescent LED and CFL: 400 Watts
- 250 Watts for multi-gang
- 150 Watts (Actual Wattage rating, not equivalent)
- Install where your Wi-Fi signal is strong
- Use your mobile device to test the signal
- Keep your mobile device close to the Dimmer until you finish the setup
Installing your Dimmer:
Installation video: Scan this QR code to watch a video walking through the Dimmer installation.
- Turn the power off: Shut off power to the switch you’re replacing at your fuse panel or circuit breaker.
- WARNING! Risk of electric shock: Incorrect installation could be dangerous or illegal. Multiple breakers/fuses may need to be turned off for safe installation. Please call a professional electrician if you are unfamiliar or uncomfortable with electrical work.
- Confirm that the power is off
- Remove the faceplate from the existing switch. Use a voltage tester to test BOTH sides of the switch. You may need to turn off more than one circuit breaker/fuse.
- Identify the NEUTRAL wires:
- Pull out the existing switch
- Unscrew the switch and gently pull it out of the wall. Do not remove any of the wires yet.
- Find the NEUTRAL wires: Look for NEUTRAL wires (usually white) in the wall. You need these to set up the Dimmer.
- NOTE: You may have a different number of neutral wires than shown.
- Test the NEUTRAL wires: Use a voltage tester to check that there is no power in the NEUTRAL wires from neighboring circuits.
- If necessary, shut off additional circuits until no voltage is found.
- Detach the NEUTRAL wires: Unscrew the wire nut connecting the NEUTRAL wires.
- Identify and label LINE and LOAD wires:
- Peel off and apply the LINE and LOAD wire labels below. If you’re unsure which wire is which, we’ll help you in the next step.
- NOTE: Your existing wires may be in different locations than shown.
- LOAD
- LINE
- Identify the GROUND wires:
- Look for the GROUND wires (usually green or solid copper) and unscrew the wire nut connecting them.
- NOTE: You may have a different number of ground wires than shown.
- Help with distinguishing LINE wire from LOAD wire:
- Remove existing switch
- Detach the remaining wires and remove the existing switch.
Once you have followed the above steps, you can proceed with installing your Wemo Smart Dimmer. For more information, refer to the product user manual.
Important to know
WARNING! Risk of electric shock
Incorrect installation could be dangerous or illegal. Multiple breakers/fuses
may need to be turned off for safe installation. Please call a professional
electrician if you are unfamiliar or uncomfortable with electrical work.
Wemo Smart Dimmer can only replace single-pole switches.
If your light can be turned on from two different wall switches, that’s a
3-way switch and Wemo Smart Dimmer is not compatible.
Neutral wires are required for setup.
These wires are typically white and can be found in your electrical box.
What you’ll need
What’s included
Recommended tools
Compatible light bulbs
All incandescent light bulbs are dimmable, but not all LEDs and CFLs are. Go
to wemo.com/bulbs for more information.
Maximum total wattage
Install where your Wi-Fi signal is strong
- Use your mobile device to test the signal
- Keep your mobile device close to the Dimmer until you finish setup
Installing your Dimmer
Installation video
Scan this QR code to watch a video walking through Dimmer installation.
Turn power off
Shut off power to the switch you’re replacing at your fuse panel or circuit breaker.
WARNING! Risk of electric shock
Incorrect installation could be dangerous or illegal. Multiple breakers/fuses
may need to be turned off for safe installation. Please call a professional
electrician if you are unfamiliar or uncomfortable with electrical work.
Confirm that power is off
Remove the faceplate from the existing switch. Use a voltage tester to test
BOTH sides of the switch. You may need to turn off more than one circuit
breaker/fuse.
Identify the NEUTRAL wires
Pull out the existing switch
Unscrew the switch and gently pull it out of the wall.
Do not remove any of the wires yet.
Find the NEUTRAL wires
Look for NEUTRAL wires (usually white) in the wall. You need these to set up
the Dimmer.
NOTE: You may have a different number of neutral wires than shown.
Test the NEUTRAL wires
Use a voltage tester to check that there is no power in the NEUTRAL wires from
neighboring circuits. If necessary, shut off additional circuits until no
voltage is found.
Detach the NEUTRAL wires
Unscrew the wire nut connecting the NEUTRAL wires.
Identify the GROUND wires
Look for the GROUND wires (usually green or solid copper) and unscrew the wire
nut connecting them.
NOTE: You may have a different number of ground wires than shown.
Identify and label LINE and LOAD wires
Peel off and apply the LINE and LOAD wire labels below. If you’re unsure which wire is which, we’ll help you in the next step.
NOTE: Your existing wires may be in different locations than shown.
Wire labels
Help with distinguishing LINE wire from LOAD wire
Remove existing switch
Detach the remaining wires and remove the existing switch.
Turn the power back ON
Test to identify the wires
Now use a voltage tester to distinguish the wires:
- Line (typically black): This wire will be powered because it carries electricity to the switch.
- Load (also typically black): This wire will NOT be powered because it carries electricity from the switch to your lights.
- Turn the power back OFF
Connect Wemo Dimmer wires
Make sure the power is OFF before proceeding.
Remove cover plate
After detaching and removing the existing switch, snap the cover plate off of
your Wemo Dimmer, and remove the sticker securing the wires.
Connect LINE and LOAD wires
Use a wire nut to connect the red LOAD wire on the Dimmer to the LOAD wire in
the wall.
Use a wire nut to connect the black LINE wire on the Dimmer to the LINE wire
in the wall.
NOTE: Your existing wires may be different colors than those shown.
Connect NEUTRAL and GROUND wires
Use a wire nut to connect the white NEUTRAL wire on the Dimmer to the NEUTRAL
wires (usually white) in the wall.
Use a wire nut to connect the green GROUND wire on the Dimmer to the GROUND
wires (usually green or bare copper) in the wall.
NOTE: Your existing wires may be different colors than those shown.
Install Dimmer 6 into the wall
Almost done! Tug on each wire nut to make sure they are secure on the wires.
Carefully tuck wires behind the Dimmer and insert the Dimmer into the box. It could get crowded in there.
Screw the Dimmer into the wall. Be careful not to overtighten the screws.
NOTE: Before snapping on the cover plate, you’ll notice an 8-digit setup
code on the dimmer. You may need this during app setup.
Finally, snap the face plate onto the Dimmer.
Turn on power
Turn on power to your Dimmer at your fuse panel or circuit breaker panel
Physical installation is complete
The light ring on your Dimmer should blink WHITE while starting up and BLUE when ready for app setup.
- BLINKING WHITE
- Starting up
- BLINKING BLUE
- Ready for app setup
- NOTE: If your Dimmer did not power up, then your load and line wires may be reversed and you need to switch them.
Go to the app for the next steps
Download and launch the Wemo App
- Create a Wemo account in the app, then add your Dimmer.
Use HomeKit Code if prompted
- If prompted, scan or type your Wemo’s code below. The 8-digit number should match the code on your Dimmer (behind the faceplate).
- Hang on to this guide. The code may come in handy if you ever need to set up this Wemo again.
Connecting to other services
- Control your Wemos with voice, create groups, and more. Connect to these services in the Wemo App.
Got questions
- Visit wemo.com/support or call us at 1-844-745-WEMO for support.
- For warranty information, go to wemo.com/warranty.
What does the light tell me
- OFF
- Wemo is off.
- SOLID WHITE
- Wemo is on and working normally.
- BLINKING WHITE
- Wemo is starting up, updating firmware, or responding to your action.
- BLINKING BLUE
- Your Wemo is ready for setup.
- GREEN
- Wemo is running a rule or timer.
- RED
- Error or low Wi-Fi connection.
WHITE/BLUE/RED: Reset your Dimmer
Press and hold the bar below the power button for reset options. Release the
button when the light is white to restart, blue to reset Wi-Fi, and red to
restore to factory settings.
References
- Wemo Smart Home | Belkin: US
- Wemo Smart Home | Belkin: US
- Live Chat, User Guides, FAQs & More | Belkin Support US
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>