KDK M40R Electric Fan Instruction Manual

: June 4, 2024
: KDK

Table of Contents

SPECIFICATIONS
SAFETY PRECAUTIONS
PARTS IDENTIFICATION
ACCESSORIES
HOW TO ASSEMBLE
HOW TO INSTALL THE FAN
HOW TO INSTALL THE REGULATOR
WIRING DIAGRAM
OPERATION
ADJUSTMENT OF CIRCULATING ANGLE
Read User Manual Online (PDF format)
Download This Manual (PDF format)

M40R Electric Fan
Instruction Manual KDK M40R Electric Fan

SPECIFICATIONS

VOLTAGE (V)	FREQ. (Hz)	POWER (W)	WEIGHT (kg)
220 – 240	50	47.5 – 54.5	4.
Type	Rating	Blade speed of Each position (r/min.)	**Power

Factor
(manly- )| Rated Air
Delivery
(m3/min.)| Number of
Speed| Fan Size (cm)| Type of Insulation
Voltage
(V-)| Frequency (Hz)| Input (W) Fan Motor**
M4OR| 127| 60| 67.| 715,825,925,1270,1370| 0.99| 86| 5| 40| Functional
Insulation
220| 60| 61| 610,800,1015,1170,1285| 0.99| 84

Use only with rated voltage.
**** Before operating this set, please read these instructions completely.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard
Ensure that the fan Is switched off from the supply main before cleaning or maintenance.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lath of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
To avoid the possibility of causing injury to users or damaging properties, please follow all the 6otplanal m written below. The manufacturer is not responsible for accidents and injuries caused by defective or deficient Installation.
Children should be supervised to ensure that they do not play with the appliance.

SAFETY PRECAUTIONS

Be sure to read and follow these safety directions
Be sure to observe the following safety precautions in order to avoid possible injury to yourself or others and damage to your belongings.
The following symbols indicate the degree of possible danger if the relevant precautions are ignored.
WARNING This term warns you that death or serious injury may result from incorrect operation of the product.
CAUTION This term cautions you that injury or physical damage to property may result from incorrect operation of the product.
■ Precautions are classified using the following symbols.
The symbol with white background denotes a PROHIBITED action.
This symbol denotes actions that are compulsory.

WARNING

■ Never try to take apart, repair, or modify this product.
** Do not take apart
• Contact the dealer for repairing this product.
■ Do not connect the line cord to the outlet until the fan has been completely assembled.
■ Do not connect this unit to a power supply other than destinated country- rated voltage.
Otherwise it may cause fire and injury.
Prohibited
■ Do not contact water.
Avoid water
Causing fire or electric shock.
■ Do not damage the power cord.
e.g. modify, put near the heat-generating appliance, abnormally twist or bend, forcefully elongate, pull heavyweight, bundle up the power cord.
Causing injury, electric shock, or even fire due to a short circuit.
Prohibited
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
■ The safety wire must be always connected.
Can cause injury
■ Ensure that the fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with sufficient strength to withstand 4 times the weight of fan.
** WARNING
■ Disconnect the power supply before cleaning.
Otherwise, it may cause electric shock.
■ Never touch the switch If your hands are wet. May cause electric shock.
No wet hand
■ Follow strictly all the instructions given in this manual for installation.
Installation errors can cause fire, electric shock, set to fall, and injuries.
Installation must be done by competent personnel.
■ Make sure to switch off the switch breaker before installation/repair
Can cause the product to suddenly turn on during repairing/installation.
■ Do not contact live parts during the installation process.
Can cause current leakage and result in fire.
■ If unusual oscillating movement is observed, immediately stop using the fan and contact the manufacturer, its service agent or suitably qualified agent.
CAUTION
■ Do not use under the following situations;

Near to gaseous fuel cooker
A place full of inflammable gas
Place expose to rain or water pour
Near insecticide
Oil corrosive solvent
High temperature
High humidity
Near chemicals, oil, dust area.

Prohibited
May cause bad effects in quality and dangerous conditions.
■ Don’t place the fan on unstable surfaces or near obstacles.
Risk of injury by a falling fan.
Prohibited
Avoid continuous exposure of direct wind from the fan.
It may cause discomfort.
Prohibited
■ Do not put your fingers into the guard or any moving part of the fan.
Prohibited
Causing injury.
■ Make sure all screws and connections are tightly screwed and secured.
****Can cause injury if drops

■ Installation must strictly follow to wiring diagram provided.
Can cause electric shock, current leakage-and fire if missing.
■ Ensure the area of the mounting fixture has sufficient strength.
Can cause injury and product to fall.
■ Do not fix at area exposed to strong vibration and knocking.
Can cause injury and product to fall:

PARTS IDENTIFICATION

ACCESSORIES

H. Bolt (2 pcs)
H. Nut (2 pcs)
** Spring Washer
**

1 Plastic clip
2 Front guard
3 Rear guard
4 Blade
5 Wing bolt
6 Motor
7 Stand
8 Mounting plate assy
9 Set bolt
10 Set nut
11 Ceiling| 12 Supporting plate
13 Set screw
14 Rod
15 Regulator base
16 Regulator cover
17 Switch
18 Switch knob
19 Capacitor
20 Cover set screw
21 Fitting hole
22 Safety wire
---|---

HOW TO ASSEMBLE

Align the projection ® with the hole © of the rear guard, and attach the rear guard to the motor.
Re-tighten 2 wing bolts C.
CAUTION Please ensure the wing bolts are fully tightened to avoid the guard from dropping.
Place the blade boss QD onto the shaft, and push it all the way until the groove 0 of the blade boss is correctly fitted to the pin QF of the shaft.
OD Align the projection © with the hole ® of the blade and attach the blade to the blade boss.
Next, turn the spinner counterclockwise in order to securely tighten the blade.
Put rear and front guards together.
Snap together the front and rear guards according to sequences 1, 2, and 3.

HOW TO INSTALL THE FAN

Caution
This fan is specially designed for mounting above 2.3m from the floor. (Mounting height shall be 2.3m)
The mounting of the suspension system shall be performed by the manufacturer, service agent or suitably qualified person.

Remove the set screw and mounting plate from the stand before installing the fan.
Install the mounting plate as shown in figure A.
Hold the stand with the set plate facing towards you and ensure to install the safety wire on the left arm.
Note: Please do not install on the right-hand side.
Loop the safety wire around the arm and clip the wire as shown in B.
The fan suspension system shall be examined, regularly, at least once every two years.
Fix the body to the mounting plate by turning the body so that hole J aligns the screw hole I.
Tighten the set screw k.

Prohibited
Do not tangle motor lead with the power cord

HOW TO INSTALL THE REGULATOR

Caution
This must be a double pole switch with a minimum 3mm contact gap in the fixed installation circuit.

Disassemble as follows Use a Philips screwdriver to remove the cover set screw.
Fix the regulator base on the wall.
Ensure that the wiring follows the wiring diagram.
Reassemble back the regulator above.

Note
The power supply wire connected to the terminal should be equipped with a splice.

WIRING DIAGRAM

CAUTION

This product is not provided with a cord and plugs with other means for disconnection from the supply. When connecting or changing the power cord or lead wire, it must be performed by qualified personnel in order to avoid a hazard. Please use 227IEC53(RVV) or the thickness of the tube is 1mm or above. (Other requirements such as the diameter of lead wire, please use according to the regulation of the country). This product should be installed with a double poles single throw switch (Breaker Switch) with a minimum 3mm contact gap in the fixed installation circuit.