Spectravision PL-REM-200 LEDpool Light Remote Control Owner’s Manual
- June 4, 2024
- Spectravision
Table of Contents
PL-REM-200 LEDpool Light Remote Control
LEDpool light Remote Control with built in transformer
OWNER’S MANUAL
PL-REM-200
Long range DuraLinkTM version
Controls SpectravisionPool Lights and 2 auxiliary circuits
Table of contents
Technical specifications Box contents Installation instructions Pairing
Handheld Transmitter & controller Handheld transmitter functions Replacing
transmitter battery Troubleshooting
Page 3 Page 4 Page 5 Page 6 Page 7 Page 7 Page 7
page 2 of 8
Technical specifications
Electrical specifications
Nominal Input voltage Output voltage on Lamp Output Max output current on Lamp
Output Max rating Relay Contact A and B
Resistive Load
Inductive Load
Transformer VA rating Fuse type
Frequency band transmitter IEC Protection Class
230 VAC 50 Hz 12 VAC 16,7 A
14A 250VAC 14A 30VDC 6A 250VAC 6A 30VDC 200VA 5x20mm cartridge fuse
5A 250V slow blow/time lag
868 MHz Class II
General specifications Controller
Ambient air temperature Humidity
Dimensions Weight Ingressprotection rate
0°C … +40°C 10% … 90% RH non condensing 195x194x90 mm 3,2 kg IP54
page 3 of 8
Box contents
1. PL-REM-200 controller 2. Handheld transmitter (DuraLinkTM version) 3.
Spare battery (type A23 12V) 4. Screws (4x) & wall plugs (4x) 5. Owners’s
manual
1
2
3
4
5
page 4 of 8
Installation instructions
· Connect a 230VAC power source to the “220-240VAC INPUT” terminal
· Connect the swimming pool lights to the “Lamp 12VAC output” terminal Make
sure the total load of pool lights does not exceed 200Watt
Optional: The “Switch A”& “switch B” terminals can be used to control
auxiliary circuits like a pool cover or garden lights.
Green status LED Spare fuse
page 5 of 8
Pairing handheld transmitter & controller
The handheld transmitter is already paired in the factory and ready to use.
The PL-REM-200 can pair with up to 6 handheld transmitters. In case a problem
arises,the pairing process can be done manually: Manual Pairing process: Make
sure the PL-REM-200 is connected to a power source. 1. Pressthe pairing button
on the small circuit board, inside the con-
troller for at least 5 seconds.
–> The LEDwill start to blink fast
2. Within 25 seconds, press any button on the handheld transmitter.
–> If the transmitter is paired correctly, the LED will flash slowly for 5
times –> If the PL-REM-200 pairing memory is full, the LED will flash 15
times.
This means 6 handheld devices have already been paired.
To unpair all handheld transmitters with the controller: Push the pairing
button for at least 5 seconds, then do nothing for at least 25 seconds.
–> The pair memory will be erased- the red LEDwill flash 5x on/off.
Pairing button Red LED
page 6 of 8
Handheld transmitter functions
Toggle the lamps ON/OFF
Go to next color scenario Toggle Output A ON/OFF Toggle Output B ON/OFF
Replacingtransmitter battery
· Remove the philips head screw and open the transmitter · Replace the
battery, respecting the polarity
Battery type: A23 12V
–
Troubleshooting PROBLEM
The controller doesn’t react to transmitter commands
The pool lights don’t work
SOLUTION
· Check the battery of the handheld transmitter
· The transmitter is not pairedcorrectly with the controller. Repeat the
pairing process
· Reduce the distance between handheld transmitter and PLREM-200 and/or remove
obstacles
· Check the green status LED · Check if there is 12VAC output
at the terminals of the controller · Check the fuse of the controller
If the fuse is ok, and there is still no 12VACoutput, contact your distributor
page 7 of 8
Contact details
Propulsion Systemsbvba Dooren 72
1785 Merchtem, Belgium Tel +32 2 461 02 53 Fax+32 2 706 59 60
www.propulsionsystems.be info@propulsionsystems.be
Garten Wasser ist unser Leben
Ihr Teich und Pool Profi
Koigarten Müller Randenstr. 4 88605 Meßkirch
www.koigarten-mueller.de VERTRAGSHÄNDLER
We reservethe rights to change all or part of the contents of this document
without prior notice
402-0019-150106