ESAB SAVAGE A40 Welding Helmet Instruction Manual
- October 30, 2023
- ESAB
Table of Contents
- SAVAGE A40 Welding Helmet
- Information
- Range of application
- Operation
- Servicing and maintenance
- Performance
- How to set the shade
- Before using the filter
- Filter Testing
- Certification and Control labels
- ADF Marking Explanations
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SAVAGE A40 Welding Helmet
Instruction Manual
SAVAGE A40 Welding Helmet
Manual Number: 0-5580EN
Revision Date: 01/15/2020
Revision Number: AC
Language: ENGLISH
WARNING
Read and understand this entire Manual and your employer’s safety practices
before installing, operating, or servicing the equipment.
While the information contained in this Manual represents the Manufacturer’s
best judgment, the Manufacturer assumes no liability for its use.
SAVAGE A40 welder protective helmet Operating Manual Number 0-5580EN
Published by:
ESAB Group Inc.
2800 Airport Rd.
Denton, TX 76208
(940) 566-2000
www.esab.eu
Copyright 2019 by ESAB.
All rights reserved.
Reproduction of this work, in whole or in part, without written permission of
the publisher is prohibited.
The publisher does not assume and hereby disclaims any liability to any party
for any loss or damage caused by any error or omission in this Manual, whether
such error results from negligence, accident, or any other cause.
Original Publication Date: 01/15/2020
Revision Date:
Record the following information for Warranty purposes:
Where Purchased:___
Purchase Date:__
Information manual for the SAVAGE A40 welder protective helmets complying with
Par. 1.4 of Appendix ll of the EC regulations. The SAVAGE A40 welding helmets
are high quality products that contribute to the comfort and safety of the
welder. SAVAGE A40
welding helmets may be used only in connection with arc welding. The chart
below shows how to choose the most suitable shade level:
Depending upon the application conditions, the next highest or next lowest
protection level can be used.
The darker fields correspond to those areas in which the corresponding welding
process cannot be used.
Information
SAVAGE A40 welding helmets afford reliable protection for the eyes whilst
electric arc welding. They offer permanent protection against UV/IR rays, heat
& sparks in any state from the clear to dark. The protection shades of the
SAVAGE A40 welding helmets have been chosen to avoid eye damage caused by the
welding arc. Do not look directly at welding rays with unprotected eyes when
the arc strikes. This can cause a painful inflammation of the cornea and
irreparable damage to the lens of the eye leading to cataracts. SAVAGE A40
welding helmets allow the welder to see the point of arc strike more
precisely. This leads to a real time saving. The helmet does not have to be
flipped up and down during welding, both hands are kept free and because of
the helmet’s light weight fatigue is reduced.
Replacing the Outer Spatter Lens:
Ensure that the helmet is always equipped with an Outside Lens (before the
filter, on the outside of the helmet) and an Inner Lens (behind the filter,
inside the helmet). These protections lenses must be replaced if broken,
damaged or covered with welding spatter to such an extent that vision is
impaired.
Inner & Outer Lenses are consumables and must be replaced regularly with
certified ESAB spare parts (CE marked).
Before using the SAVAGE A40 helmet for the first time the protective films
must be removed from the Front Spatter Lens (drawing 1). The films cannot be
removed from the Front Spatter Lens with the Lens in place. Please follow the
instructions below to remove the Spatter Lens.
Inserting and removing a new protection lens:
To insert the new outer protection ➃ lens the filter must be removed by
unscrewing the two retaining screws ➇ from the inside of the helmet ➀. The old
protection lens can then be removed and the new lens inserted followed by the
light seal cradle ➅, ADF ➆, inner protection lens ➄ and then the ADF retaining
frame ➇ and finally replace the two retaining screws (see drawing 2).
Range of application
The SAVAGE A40 welding helmets can be used for the following applications:
- Electrode
- MIG
- Mag
- TIG (>=5A)
They are not suitable for use with laser systems and oxyacetylene (gas
welding) applications. The welding filter must not be used for any other
purpose other than welding. They should never be used as sunglasses when
driving as this could lead to incorrect identification of the color of traffic
light.
The welding filters operate well under extreme low lighting and very strong
sunlight.
Operation
Adjustment of headgear:
SAVAGE A40 welding helmets are equipped with a comfortable headgear that can
be adjusted in three different ways.
Servicing and maintenance
SAVAGE A40 welding helmets should not be dropped. Do not place heavy objects
or tools (hammers etc.) on or inside the helmet so as not to damage the
electro-optical filter.
Always make sure that the helmet is equipped with an outside and inner lens
(in front of the filter on the outside and on the inside behind the filter).
These protection lenses must be replaced if damaged in any way (see overleaf).
They are consumables and should checked and replaced regularly.
The filter should be cleaned when changing the protection lenses.
This can be done by any of the following ways:
- Wipe with a clean, dry piece of cloth.
- Clean with a piece of smooth cloth moistened with pure alcohol.
- Clean with a commercial disinfectant
- If used properly the welding filter requires no further maintenance during its lifetime
If a filter should be replaced on a SAVAGE A40 welding helmet, use exclusively
certified products (DIN-CE marks).
We recommend the use of ESAB welding filters in all SAVAGE A40 helmets.
The filter itself contains no special or toxic products and can be disposed of
in the same way as other electronic devices.
Performance
To allow the filter to switch both sensors on the front of the filter must not be covered, the filter then switches to the dark state when the arc strikes and to the clear state when it stops. The filter switches to the light state when the welding arc stops.
How to set the shade
On the SAVAGE A40 set the shade by turning the knob on the outside of the
helmet (pos. 1).
The most suitable setting can be found on the Chart in this brochure or chosen
using your experience. This setting can also be made manually during the
welding process.
Turning clockwise =darker
Turning anti clockwise = clearer
Switching Grind mode / Welding mode
On the SAVAGE A40 exchange the Welding and Grind mode by pressing the knob
on the shade knob outside of the helmet.
On Welding mode, by pressing the knob and hold for 2 seconds. The mode will be
changed from Welding to Grind.
The green Grind light will flash (pos.4)
On Grind mode, By Pressing the knob and hold for 2 sec- nods. The mode will be
changed from Grind to Welding. The green Grind light will stop flashing
(pos.4)
How to replace battery (For
Replaceable Battery Version Only)
When the LED (pos. 5) on ADF turns red, the battery needs replacement. Follow
instructions below. Otherwise, ADF won’t work correct and can cause harm to
the operator.
-
Remove battery cover from battery case (pos .1)
-
Take battery out and fit a new battery inside battery case.
Note: “+” is on top. (pos. 2) -
Assemble battery cover onto battery case.
Before using the filter
We recommend the following adjustments to be made:
- Turn the sensitivity knob clockwise to the max. setting (pos. 2). Depending upon the surrounding light the filter will switch to the dark state or will flicker (if the surrounding light is very low, the filter may not switch to the dark state).
- Turn back the sensitivity knob (pos.2) until the filter switches to the clear state.
- The filter is now set to its optimum sensitivity (According to the surrounding light conditions).
Range of use for the SAVAGE A40
All arc welding applications with the exception of TIG<5A.
Available shade – 9-13 (pos.1).
Setting the delay
The clearing delay can be adjusted manually by turning the delay knob (pos. 3)
between a fast clear (0.1 sec) fully anticlockwise and a slow clear (1.0 sec)
fully clockwise.
Spare parts SAVAGE A40
Items without a part number are not available as spare parts.
No. | Part No. | Description |
---|---|---|
1 | 700000480 | SAVAGE A40 9-13 Black |
1 | 700000481 | SAVAGE A40 9-13 Yellow |
1 | 0700000490x- | SAVAGE A40 9-13 Replaceable Battery Black |
1 | 0700000491x- | SAVAGE A40 9-13 Replaceable Battery Yellow |
2 | 700000483 | ESAB Head Gear |
3 | 700000414 | Sweat band |
4 | 700000010 | Front cover lens |
5 | 700000482 | Inside cover lens |
6 | 700000418 | ADF cradle |
7 | 700000419 | Lens retainer with screws |
*Not Available in all regions.
Filter Testing
Before use of the welding helmet the auto darkening filter (ADF) and helmet needs to be checked according to the following procedure:
- Check outer protection lens is clean and can be seen through.
- Ensure the sensors are not covered in any way and are clean.
Once these checks have been carried out you can now test the ADF.
Turn the outside shade knob to the darkest setting (shade 13) and set the
sensitivity to the highest setting (turning clockwise). Now point the sensor
towards a light source such as an overhead light, lamp etc. The ADF should now
switch to the dark state (please note if the ADF is stored in a dark area away
from light it may need to be left out in strong light for 20 minutes to absorb
power, after 20 minutes if the ADF does still not react then there is an issue
with the sensor). Once the filter is in the dark state you can check the shade
variation is functioning correctly, simply turn the shade knob anti-clockwise.
By doing this, the shade should get lighter. If the shade does not appear to
alter then you have an issue with the shade variation.
To test the delay function, set the delay to the maximum setting. Now move the
filter sensor away from the light source it should take 1 second to return to
the light state, now after the delay setting to the minimum and repeat the
process, the time taken to return to the clear state should be 0.1 second. If
the ADF does not react in this way, then there is an issue with the delay
function.
Testing the sensitivity. Set the sensitivity to minimum setting now point the
ADF at the light source you used to test the other functions (if filter
switches to dark state move away until the filter returns to clear state)
slowly turn the sensitivity until the filter switches to dark state (if it
does not then move closer to the light until it reacts) if the ADF does not
react then there is an issue with the light sensors.
If any of the functions fail during test or in use, then please do not use the
ADF and contact your local distributor.
WARNING The auto-darkening filters fitted in the SAVAGE A40 helmets are
not waterproof and will not work properly if they have been in contact with
water.
Welding helmets and filters only resist a certain amount of heat. Please do
not place them near naked flames or hot work areas etc.
Operating temperature of electronic filter minus 10º to plus 65º C. Materials
that may get in contact with the wearers skin could cause Allergic reactions
to susceptible individuals.
Certification and Control labels
European Conformity mark.
This confirms that the product fulfils the requirements of the PPE Regulation
2016/425 ANSI Z87.1
AS/NZS
CSA Z94.3
NOTIFIED BODY
ECS GMBH
REGISTRATION NUMBER: 18
ECS GmbH
Obery Bahn Strasse 74
73431 Aalen
Germany| EN379:2003+A1:2009
EN 175:1997
EN166 B:2002
NOTIFIED BODY
ECS GMBH
REGISTRATION NUMBER: 18
ECS GmbH
Obery Bahn Strasse 74
73431 Aalen
Germany
---|---
ADF Marking Explanations
CE 4/9-13 ESAB 1/1/1/2/379
4 – Light state scale number
9 – Lightest dark state scale number
13 – Darkest state scale number
ESAB – Manufactures identification
1 – Optical class
1 – Diffusion of light class
1 – Variation in luminous transmittance class
2 – Angle of dependence classification
379 – Number of the standard
ESAB AB operates a policy of continuous improvement. We therefore reserve the
right to make changes and improvements to any of our products without notice.
ESAB AB Lindholmsallén 9
Box 8004 402 77 Gothenborg Sweden
Tel: +46 (0) 31 50 90 00
www.esab.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>