JAY-tech FTY18 Fitness Tracker User Manual

: June 4, 2024
: JAY-Tech

Table of Contents

JAY-tech FTY18 Fitness Tracker
SAFETY MEASURES
TIPS BEFORE USE
INSTALL “FITPRO” APP ON YOUR SMARTPHONE
CONNECTING FITNESS TRACKER WITH FITPRO APP
WRISTBAND FUNCTIONS
FITNESS TRACKER MENUS
APP FUNCTIONS AND SETTINGS
TECHNICAL DATA
SERVICE PROCESS
EU CONFORMITY DECLARATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JAY-tech FTY18 Fitness Tracker

FIRST STEPS

ATTENTION:
Please fully charge your smartwatch before the first use, check that the product is complete and remove the protective films from display and back side (sensor area).

Please read this user manual carefully before using the product. It contains important information for your safety as well as instructions for use and maintenance.
Keep this user manual in a safe place.

SAFETY MEASURES

Do not open the housing of the product or take it apart.
Keep the product away from extremely high or low temperatures.
Do not use the product in a sauna or steam bath.
Do not leave the product exposed to the sun for a long time.
Do not expose of the product by burning, the internal battery can explode.
The product contains an internal battery that can not be changed by the user.
Do not read any incoming call notifications or other information on the product display while driving a vehicle, or in any other situation where distraction can lead to dangerous situations.
Reading of distance traveled can be inaccurate. This is only for reference and should not be used for navigation.
The product should normally be worn one finger width below the wrist. At the same location, you would normally wear an armband.

ATTENTION:
This product can cause skin irritations. Contact over a prolonged time can promote skin irritations or allergies in some users. If signs of skin redness, swelling, itching or skin irritation are present, please discontinue the use of this product. Further use may cause renewed or more severe irritation, even if previous symptoms have subsided. Contact your dermatologist if symptoms persist.

WARNING
Measurements for pulse and blood pressure should not be used for self- diagnosis or treatment. Users with blood pressure or circulatory disorders should undergo treatments only in consultation with a physician. The measurement results of this fitness tracker are for reference only and should not be used for medical purposes.

TIPS BEFORE USE

Please read this user manual carefully for correct use and keep it in a safe place for future reference. Please charge the fitness tracker for 2 hours before first use. During the charging process, the battery symbol will appear on the display.

INSTALL “FITPRO” APP ON YOUR SMARTPHONE

Install the “FITPRO” app on your smartphone by scanning this QR code, or searching for the app in the App Store (iOS) / Google Play (Android).

Android / iOS
Compatible operating system and requirements: Bluetooth 4.2 Android 5.0 and above iOS 9.0 and above.

CONNECTING FITNESS TRACKER WITH FITPRO APP

For initial use you have to pair the fitness tracker with the app. After successful pairing, time will be automatically synced with the fitness tracker.

Launch the FitPro app – click “Set” in the app
Tap on the green bar „Connect devices to get more functions“ – click on the device, to start a connection.
After successful pairing the app will automatically save the Bluetooth address of the wristband. When the app is launched or runs in the background, it will automatically search for the wristband and connect to it.
Make sure, that the app runs in the background and all permissions have been granted in the phone’s system settings, such as running in the background and reading contact information.

WRISTBAND FUNCTIONS

To switch the device on when it is switched off, press the control panel (circle on display) for longer than 3 seconds.
When the device is switched on, but the display is off, press the control panel only briefly, to activate the display.
Press the control panel of the display for approx. 2 seconds, to enter the submenu, if available. Lightly tap on the control panel to move through the features of the submenu.
ATTENTION! The wristband reset function deletes all data of the wristband (e.g. step counter).
In the home screen display, hold the control panel to switch between dial faces. After switching, the display will switch off if no further operation is performed within 5 seconds.

FITNESS TRACKER MENUS

Home screen: Time, date (steps and pulse if applicable)
Steps + distance + calories burned
Health: Pulse, blood pressure, blood oxygen level – press the control panel for approx. 2 sec. to start the measurements.
Sport: Press the control panel for approx. 2 sec. to switch between the sports “running”, “jumping rope” and “situps” by tapping briefly. After your selection, press the control panel for approx. 2 sec. to start the timer. Hold again to reset the time to zero. ATTENTION! The timer can not be paused!
Message: Launch the FitPro app – Set – Message Push – turn on the permission, so that messages can be pushed to your wristband after your phone has received them. Only the last 3 messages received will be displayed.
Music: Hold the control panel on your fitness tracker for approx. 2 sec. to open the submenu. Here you can control the music playing on your smartphone. You have the following choices: Back one song (left arrow), forward one song (right arrow), or pause/play. Briefly tap the control panel in the submenu for the chosen function. The symbol colored in red is the available function. To choose the function, hold the control panel for approx. 2 sec. Note: The red left arrow is to leave the menu.
More: a) sleep When you fall asleep, the wristband automatically switches to sleep monitoring mode, automatically determining your sleep quality during the night. You can check your sleep data on the app, after synchronization has been completed.

Note:
Please wear the wristband while sleeping, so data can be recorded. Sleep will be recognized after 10:00 PM. Sleep data can be synchronized with the app after 4 hours of sleep. b) Weather, c) “Take a picture”, hold the control panel for approx. 2 sec. to start the process. Please note that the app must be launched for this, d) “Search for”, hold the control panel for approx. 2 sec., and the wristband will search for your smartphone, which will answer with a beep, e) “Reset”, hold the control panel for approx. 2 sec. and your smartwatch will reset and restart. ATTENTION: All data will be deleted! F) QR code, g) information about the fitness tracker, and hold the control panel to switch off the smartwatch.

APP FUNCTIONS AND SETTINGS

Note:
Some of the functions require you to log in. Please register for this on the home screen. You can skip the registration process by tapping “skip” in the top right corner.

Explanation of the app bottom bar symbols:

User proﬁle “Mine”
Please set your personal data in the user profile after launching the app.

Setting “Set”
If not already done so, you can connect to your fitness tracker here. Press on the submenu “find” and the fitness tracker will vibrate.

Under “Message push” you can choose, which messages you want to receive. In “Dial settings” you can choose the dial design under “Recommended”. Choose a design and tap “Sync dial”. The design is downloaded and updated.

“Reset device” – Attention, this will reset the device and delete all data!
“Remove” – Data will be deleted and the device removed.
“Others” – Vibration settings of the fitness tracker.

Top symbol bar:

Lift your wrist: The fitness tracker‘s display is activated when you move your wrist.
DND mode: Timer for not receiving messages.
My alarms: Setting of alarms
Long sitting: Setting for reminders when sitting too long.

Tracking “Running”!
At the top you can choose between walking, running and bicycling. Tap “Start” to start the tracking (for this you must be registered and logged in).

First-page “Steps”
Here you can check the number of steps, distance traveled, calories burned, health assessment, pulse, sleep and “healthy habits” (registration necessary)

Tips for Android users:
When using the reminder function, you must set that the FitPro app can run in the background. We recommend granting the FitPro app all permissions.

Note for charging the ﬁtness tracker
Please remove the wristband at the top of the housing. Plug the connector in a regular USB charger (not included) or the USB port of a laptop. The charging process is indicated on the display with a battery symbol.

TECHNICAL DATA

Battery: 90 mAh lithium-polymer
Display: 1.44“ / 3.66 cm with a single touch (single touch control panel)
Bluetooth 4.2
Operating temperature: -10°C ~ 50°C
System: iOS 9.0 and above / Android 5.0 and above

SERVICE PROCESS

If you have any reason for complaints or your device has a defect, please contact your retailer or the service department of JAY-tech GmbH, to arrange for customer service.

Service hours: Mon – Tue from 8:00 AM to 5:00 PM Friday from 8:00 AM to 2:00 PM
Telephone no.: 02161 / 575 8950
E-mail: info@jay-tech.de

Please do not send the device to our address without being requested by our service team. Shipping costs and risks of loss are borne by the sender. We reserve the right to refuse acceptance of unauthorized shipments and send such shipments back to the sender freight collection or at the sender’s expense.

EU CONFORMITY DECLARATION

The company JAY-tech GmbH hereby declares that the described product complies with the directive 2014/53/EU and others, applicable to the product. The full text of the EU conformity declaration is available under the following internet address: www.jay-tech.de.

The device carries the CE mark and complies with all required EU standards.

DIRECTIVE 2012/19/EU ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)
Waste equipment does not belong in household waste! If the device at some point in time can not be used anymore, each consumer is required by law to dispose of waste equipment separately from household waste, e.g. at a municipal/district collection point. This ensures that waste equipment is recycled properly and negative effects on the environment are minimized. Thus electrical devices are marked with this symbol.

JAY-tech GmbH