Luciamo LED Solar Floodlight with Sensor Instruction Manual
- October 30, 2023
- Luciamo
Table of Contents
SOLAR LED MHCS 10W
TECHNICAL DATA:
Power | 10W |
---|---|
Brightness | 1500LM |
LEDS | SMD2835*44pcs |
Battery Pack | Li-ion battery, 18650, 3.7V, 3600mAh, 13.32Wh |
Mono Solar Panel | 4.5Wp, 5.5V |
Digital PIR Sensor | 120°/6 Meters |
Lighting Area | 60-80m² |
Lamp Size | 153 x 144 x 33 mm |
Solar Panel Size | 202 x 221 x 24 mm |
Installation Height | 2~4 Meters |
Installation Distance | 8-10 Meters |
Warranty | 2 years warranty (battery 1 year warranty) |
Beam Angle | 120*60°, maximum lighting design, bigger lighting area |
Working Modes | Auto Sensor Mode, Keep Lighting Mode |
Charging Time | 4~6 hours strong sunshine to fully charge |
Lighting Time | Up to 60 hours according to different working mode |
Lamp Bracket | 360° adjustable |
Solar Panel Bracket | 170° adjustable |
Connection Cable | 5 meters long |
REMOTE CONTROL bUTTONS
| ON, lamp turns on,. ON/OFF switches on the remote control are with memory
function.
---|---
| OFF, lamp flicks 3 times then turns off.
| Auto, the lamp enters Auto Sensor Mode directly. Lamp brightness and
lighting time are not selectable under Auto Sensor Mode.
| Keep Lighting Time
---|---
| 60% brightness
| 30% brightness
| +15% brightness by each press (Max 60%)
| -15% brightness by each press (Min 15%)
These 7 keys (on grey background) are only used to adjust lighting time and
brightness of Keep Lighting Mode. First press the 3H/5H/8H and the lamp will
enter Keep Lighting Mode automatically, then press to set desired
brightness.
For example: Press Lamp lights up at night and keeps 45% brightness for 5h.
After 5h or when battery power is less than 30%, lamp turns to Auto Sensor
Mode.
TWO OPTIONAL WORKING MODES :
Please press the button on the lamp first, the lamp will automatically turn on and enter Auto Sensor Mode, and the remote control is activated at the same time. Then, please use remote control to set desired working mode.
AUTO SENSOR MODE
Lamp automatically lights up at night and turns to full brightness when motion is detected in the range <6m, then turns to lower brightness in 60 seconds of no motion.
When not fully charged, the lamp goes into energy saving mode, maintaining brightness at 60% for maximum working time.
KEEP LIGHT MODE
Lamp automatically lights up at night and keep selected brightness for 3H/5H/8H, after which or when the battery power is less than 30%, lamp turns to Auto Sensor Mode.
TECHNICAL NOTES:
- Please note that there is a very low risk of explosion of the battery due to its lithium-ion design.
- The solar panel should be placed in a place where it absorbs a sufficient amount of sunlight.
- Please note that the maximum lighting time of the LED luminaire will vary depending on the absorption time and the intensity of the sun‘s rays.
- The luminaire is automatically turned on at dusk (unless it is turned off remotely – using the appropriate button by the user).
- The recommended mounting height of the luminaire should be 3-5m higher than the given reference point (e.g. 3m above the ground).
- The luminaire is equipped with an internal, replaceable battery. If it is necessary to replace it, please contact the seller in order to select a suitable, new item.
- In order to start the luminaire after disconnecting and reconnecting the battery, or to replace it, the solar panel should be directed towards the sunlight.
NOTES ON USE:
- It is forbidden to use a solar module other than the one originally attached to the luminaire. Any changes in this connection may result in injury and will invalidate the product warranty.
- Remember to clean the motion sensor from time to time from dust and sediment with a damp cloth.
- Periodic cleaning of the solar module shell is also recommended. A dirty cell can reduce the photovoltaic performance.
- In both cases, in order to avoid discoloration on the casing, do not use strong cleaning agents, e.g. those based on alcohol.
BATTERY REPLACEMENT:
Before replacing the battery, turn off the luminaire, making sure that the On/Off button is in the Off position. Using the available tools, unscrew the bolts from the battery casing and remove its cover. Remove the used battery, first disconnecting it firmly from the power plug. The assembly of a new battery is carried out in a similar manner to the disassembly.
UTILIZATION:
In accordance to European Directive 2012/19/EU regarding electrical and electronic equipment, the WEEE with label such indicates label, the under need of penalty separate of fine, collection can not of be used thrown out into electrical ordinary and electronic garbage together equipment. with Products other wastes. These products may be harmful to the natural environment and human health, it requires a special form of treatment/ recovery / recycling/ disposal. You can find out about the utilization possibilities of a warn out device in the appropriate city or commune office.
Kobi-Light Sp. z o.o. Spółka Komandytowa ul. Boya-Żeleńskiego 2, 35-105 Rzeszów
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>