Mockmill MOCK Flaker Mixer Attachment for Various Kitchen Mixers Instruction Manual

October 30, 2023
Mockmill

**Mockmill MOCK Flaker Mixer Attachment for Various Kitchen Mixers Instruction Manual

**

JOIN THE FOOD REVOLUTION

Dear Customer,

we are very pleased that you have purchased one of our Mockmills and welcome you to the world of cereals:

Taste: Freshly flaked tastes better.
Feel: Homemade is good for you and easy to digest.
Explore: Quality you make yourself, quite simply!

Try out your Mockmill right away and enjoy the variety, the great taste and the full aroma of freshly flaked whole grains.

We hope you will enjoy discovering and enjoying of new individual creations.

We also look forward to your feedback.

Kind regards
Paul Lebeau und Martina Mock

Good to have you with us!

Overview

PRECAUTIONS AND SAFETY INSTRUCTIONS

Before using your Mockmill for the first time, please read this section carefully.

Selection of grains
Use only cleaned grains. Unclean grains may contain small stones that can damage the rollers.
Flaking grains other than listed on page 18 may damage the machine and invalidate the warranty. The range of possibilities is enormous, so for advice on using other grains, please contact us via email: info@mockmill.com

For home use
To avoid overheating your mixer, let it rest after flaking one full hopper of grains. As a general rule, one should let the mixer cool down for about 45 minutes  before continuing. Check yourmixer’s manual for more specific instructions.

Supervision
The Mockmill may only be operat ed under proper supervision (and not by children).

Warning
Never reach into the milling rollers or insert any objects (e.g. spoons, screwdrivers) when the appliance is switched on. Failure to observe this warning may result in injury (such as injury to fingers), and damage to the rollers could occur.

Cleaning
Dismount the flaker from the mixer before cleaning. The unit must never be allowed to get wet.
Above all, never immerse it in water or other liquids. Simply wipe the outside of the housing very lightly with a damp cloth.

COMPONENTS

A: Housing closure
B: Funnel
C: Drive shaft
D: Alignment pin
E: Fastening screw
F: Housing with scale
G: Adjustment slide

Components

ASSEMBLY / PREPARATION

  1. Loosen the fastening screw and remove the mixer’s attachment hub cover.
  2. Insert the Mockmill into the attachment hub, aligning the drive shaft with the square hub socket.
  3. Rotate the attachment back and forth to find the fit if necessary.
  4. When the Mockmill is properly seated, the alignment pin on the Mockmill will fit into the notch on the hub rim.
  5. Tighten the extra­long fixing screw provided until the Mockmill is securely attached to the mixer.

Exception: KitchenAid Mini
Please use the original KitchenAid screw

Assembly Instruction

GETTING STARTED

Before first use
Flake a handful of oats and then throw the flakes away. By doing this, you remove from the rollers any possible manufacturing residues.

Getting started – please follow in order
Verify that the Mockmill is firmly seated on the mixer.
Then you are ready to start!

  1. Setting the thickness: Simply slide the funnel to the desired position, the scale indicates the position for thicker or thinner flakes.
  2. Load your cereal / seeds into the hopper.
  3. Set the mixer to “3” for flaking.
  4. Switch off after the desired amount of flakes has been produced.

Cleaning / sticky rollers
If the machine is to be left standing for a long time, e.g. before a holiday, we recommend that you clean the rollers. This is very easy (see next page). See also the demo video on our website at:

www.mockmill.com
⟶ Service/Help ⟶ Help/Support

OPENING AND CLEANING

If your flaker unit is stubbornly dirty, it may be useful to open it up.
Then you can clean the flaking unit and remove grain residues from the housing with a soft brush or a wooden spatula.
Proceed as follows:

  1. If necessary, remove the Mockmill from the mixer and pull the funnel out of the adjustment slide.

  2. Carefully remove the dome shaped casing closure. To release it, move the adjustment slide using one finger. You will feel some resistance; carefully increase the force until the closure is released.
    Opening and Cleaning Instruction

  3. a. Stand the Mockmill upright, grasp the outer casing with both hands and push it down onto the table.

b. Now hold the drive flange with one hand and pull the cylindrical housing away with the other hand.
Opening and Cleaning Instruction

  1. a. Now push the adjustment slide towards the flange side (4a), then lift it up and out (4b, 4c).

b
Opening and Cleaning Instruction
c

  1. Now you can clean the rollers with a coarse brush and remove any residue you find among the gears.

  2. a. To reassemble, simply proceed in reverse.
    Take special care that when mounting the round housing cylinder, the guide groove (6b) slides into the tongue (6a).

b
Opening and Cleaning Instruction

  1. When mounting the housing lock, make sure that it is correctly aligned. The guide groove of the housing lock and the tongue of the inner plate are marked accordingly.Opening and Cleaning Instruction

WHAT CAN I FLAKE WITH THE MOCKMILL?
Grain table for flaker attachment Mockmill Flakes

Readily flaked| Disrupted for bioavailability| **Requires preparation***
---|---|---
Oats| Golden millet, quinoa, brown millet, hemp seeds, sesame seeds, linseeds, buckwheat| Einkorn, Naked Barley, Buckwheat

***** Briefly soak the grains in a kitchen sieve and then place them on a towel to dry.
Once dry, they can be flaked.

DO YOU HAVE ANY QUESTIONS?

Our hotline:
+49 6162 50 99 66 0
info@mockmill.com

FURTHER INSTRUCTIONS FOR USE

On our website at: www.mockmill.com ⟶ Service/Help ⟶ Help/Support you will find videos for further application notes.

Troubleshooting

In the unlikely event that you experience a problem with your
Mockmill or should you have any questions as to how it works,
please contact us by phone (+49 61 62 50 99 66 0) or email
info@mockmill.com. Almost all problems can be solved by our technical staff by phone.

TECHNICAL DATA AND CONTENTS

Description:
Flaker attachment
Mockmill Flakes

Suitable for kitchen machines of the brands:
Electrolux (some models),
KitchenAid (all models),
Kenmore (some models).

Fineness:
Adjustable for desired flake thickness.

Flaking throughput:
120 g per minute (thin flakes and with the mixer set at 3).

Hopper capacity:
600 g

Crushing mechanism:
Plastic, stainless steel

Housing:
Plastic

Dimensions:
27 x 10.5 x 18 cm

Weight:
1,2 kg

Warranty:
2 years

Colour:
White

Technical changes reserved.

Contents of delivery:
Flaker attachment with funnel, extra­long fastening screw, operating instructions.

WARRANTY AND REPAIR

Wolfgang Mock GmbH guarantees Mockmill Flakes to be free of material or manufacturing defects for a period of two years from the date of purchase. To validate your warranty, please register at: www.mockmill.com ⟶ service/help. The warranty does not cover damage to fragile parts, e.g. the hopper, nor damage caused by misuse. Within the warranty period, a defective unit will be repaired or replaced.

If a repair becomes necessary, please call us or send an email to info@mockmill.com before returning the defective mill so that we can locate the nearest authorised service centre for you.

WOLFGANG MOCK GMBH
Marie­Curie­Str. 5
64823 Groß­Umstadt
Deutschland
+49 61 62­50 99 66 0
info@mockmill.com

Available at
DeliverDeli.com

Mockmill MOCK Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals