CAMDEN DOOR CONTROLS CM-221 ValueWave Touchless Switches Instruction Manual

CAMDEN DOOR CONTROLS CM-221 ValueWave Touchless Switches

Product Information

The CM-221M Touchless Exit Switch is a door activation device that allows you to unlock your door or trigger your door operator to open the door without having to touch the switch. It comes with a remote LED triggering feature that allows you to control the LED states remotely. This unit operates on 12 to 24 VDC +/- 10% voltage and has a current peak of 45 mA. It has a PIR contact rating of 1 Amp @ 30 VDC with common, N.O., and N.C. contacts. The switch is available in two dimensions – Narrow (1 3/4 W x 4 1/2 H x 1 1/4 D) and Single Gang (2 3/4 W x 4 1/2 H x 1 1/4 D).

Specifications:

• Voltage: 12 to 24 VDC +/- 10%
• Current Peak: 45 mA
• PIR Contact Rating: 1 Amp @ 30 VDC with Common, N.O., and N.C. contacts
• Dimensions:
  • Narrow: 1 3/4 W x 4 1/2 H x 1 1/4 D (43 mm x 114 mm x 31 mm)
  • Single Gang: 2 3/4 W x 4 1/2 H x 1 1/4 D (70 mm x 114 mm x 31 mm)

Features:

• Touchless operation
• Remote LED triggering
• Toggle feature to trigger the door to remain in the unlocked position
• Adjustment for distance (2 to 8, 5 to 20 cm)
• Adjustment for time delay (0.5 to 20 seconds) for toggle

Operation at a Glance:

In a typical application, as you approach the CM-221, the LED will be red. When you wave your hand in front of it, it will change the LED to green and trigger its relay to change state and unlock your door, or trigger the door operator to open the door. The toggle feature can be used to trigger the door to remain in the unlocked position until you wave your hand a second time to relock it.

Installation Instructions:

1. Make sure not to use AC Voltage for this unit. Refer to section 8 for power requirements.
2. Configure the CM-221M by adjusting the range of detection and output duration.
3. Wire the CM-221M to a maglock by connecting the ground (-) of the maglock to the ground (-) of the VDC power supply. Next, connect the (+) of the maglock to the (N.C.) of the manual pushbutton. Connect the common (com) of the manual pushbutton to the PIR sensor purple wire (normally closed.) Jumper the PIR sensor blue (common) and red (power +) wires and then connect them to the (+) positive terminal of the DC power supply. Wire the PIR sensor
   black (-) wire to the negative (-) terminal of the DC power supply.

Configuring the CM-221M:

The CM-221M can also have its LED states controlled remotely. This is done by installing the supplied jumper from the parts bag onto the two pins on the back of the unit. Once installed, the green and red LED’s can be triggered to change by bringing either one low (to ground). The yellow wire controls the green LED, whereas, the white wire controls the red LED. They can be individually turned on or off, or they can be wired to a SPDT contact to turn red on and green off, or vice versa.
Mode pins: Open (Default position)= Internal mode where the LED colours will be controlled by the IR sensor. Shorted = External mode where the LED colours will be controlled by Yellow and White wires.

PARTS INCLUDED IN THE BOX

• (1) CM-221M Touchless Exit Switch with Manual Override pushbutton
• (1) Parts bag (Contents: (2) 6-32 X 1/2″ oval head Phillips ss screws, (2) 6-32 X 1/2″ snake eye s/s flat head screws, (1) Key for tamper proof screws (snake eye), (1) Jumper for factory external LED control)
• (1) User/Installation Manual
• (1) Faceplate Gasket

GENERAL DESCRIPTION

The CM-221M Hands-Free Switch uses active infra-red microburst sensor technology, designed for use in ADA compliant automatic door control applications and access control.
The CM-221M switches eliminate the spread of germs by avoiding physical contact, and provide greater convenience when moving through the premises. The switches are available with stainless steel faceplates, in narrow (jamb) or single gang.
All models are ROHS compliant with lead-free construction. Built-in remote LED switching allows for integration with third-party applications, such as guard and nurse station annunciators. Adjustable time delay from 0.5 to 20 seconds and an adjustable range from (2” to 8” / 5cm to 20cm).

Dimensions

• Narrow:
  1 3/4″ W x 4 1/2″ H x 1 1/4″ D (43 mm x 114 mm x 31 mm)

• Single Gang:
  2 3/4″ W x 4 1/2″ H x 1 1/4″ D (70 mm x 114 mm x 31 mm)

SPECIFICATIONS

FEATURES

• Built-in Red and Green LED indication.
• Factory default = Red (Standby), Green (Triggered)
• Red and Green LEDs can be controlled by sensor or externally
• Adjustable detecting distance: 2 to 8 Inches (5 cm to 20 cm)
• Adjustable Time Delay: 0.5 seconds to 20 seconds
• Toggle function selection available
• IP65 rating
• IR lens to provide stable and reliable operation

OPERATION AT A GLANCE

In a typical application, as you approach the CM-221, the LED will be red. When you wave your hand in front it will change the LED to green, and trigger its relay to change state and unlock your door, or trigger the door operator to open the door. The toggle feature can be used to trigger the door to remain in the unlocked position, until you wave your hand a second time to relock it.

NOTE : Do NOT use AC Voltage for this unit. Please see section 8 for power requirements

CONFIGURING THE CM-221M

Range of Detection and Output Duration
Looking at the back of the CM-221M with the Mode pins located at the top, you will see two adjustment potentiometers. The one on the left can be turned clockwise to set the range of detection (2” to 8” / 5cm to 20cm), and the one on the right will set the duration of the output (0.5 to 20 seconds).
If the output needs to be triggered and maintained in that state until triggered once more, then the Toggle feature can be used by turning the output duration adjustment potentiometer to the fully clockwise position.

Remote LED Switching
The CM-221M can also have its LED states controlled remotely. This is done by installing the supplied jumper from the parts bag onto the two pins on the back of the unit. Once installed the green and red LED’s can be triggered to change by bringing either one low (to ground). The yellow wire controls the green LED, whereas, the white wire controls the red LED. They can be individually turned on or off, or they can be wired to a SPDT contact to turn red on and green off, or vice versa.

MODE PINS:

• OPEN (Default position) =  Internal mode where the LED colours will be controlled by the IR sensor.
• SHORTED = External mode where the LED colours will be controlled by Yellow and White wires.

WIRING THE CM-221

Connection to a Maglock
Connect the ground (-) of the maglock to the ground (-) of the VDC power supply. Next connect the (+) of the maglock to the (N.C.) of the manual pushbutton. Connect the common (com) of the manual pushbutton to the PIR sensor purple wire (normally closed.) Jumper the PIR sensor blue (common) and red (power +) wires and then connect them to the (+) positive terminal of the DC power supply. Wire the PIR sensor black (-) wire to the negative (-) terminal of the DC power supply.

# /Color /Function

1. Red 12 to 24 VDC
2. Black 0 VDC (Ground)
3. Yellow Green LED controlled by external mode.
4. White Red LED, controlled by external mode.
5. Green Relay: Normally Open
6. Blue Relay: Common
7. Purple Relay: Normally Closed

# /Color /Function

1. Red Common
2. Black Normally Open
3. White Normally Closed

Connection to a Door Operator

Connection to an External Strike

POWER

The CM-221M is a VDC device only and will accept a range of VDC power from 12VDC to 24VDC (+/- 10%). Do not connect AC voltage to the CM-221M at any time

Note : A linear output VDC power supply is strongly recommended. If using power from other than Camden’s CX-PS13 filtered regulated power supply, you must measure the provided power before applying power to the CM-221M. Voltages of more than 10% over the specified acceptable range or using a power supply with large amounts of AC voltage on it (unfiltered unregulated power such as a transformer and a rectifier) may damage the CM-221M and void the warranty

DIMENSION

ORDERING INFORMATION FOR REPLACEMENT PARTS

ORDERING INFORMATION FOR REPLACEMENT PARTS

ITEM NUMBER| PART NUMBER| DESCRIPTION
1.| 60-31A083| TOUCHLESS SENSOR SWITCH WITH EXTERNAL LED CONTROL

| A| 60-49B040- xxx| NARROW STAINLESS-STEEL FACEPLATE
B| 60-49H009L- xxx| SINGLE GANG STAINLESS-STEEL FACEPLATE

| A| 60-59H000| GASKET FOR NARROW GANG TOUCHLESS SWITCH
B| 60-59H001| GASKET FOR SINGLE GANG TOUCHLESS SWITCH
PARTS KIT
ITEM NUMBER| PART NUMBER| DESCRIPTION

4

|

60-34B093

| (A)    6-32 X 1/2” OVAL HD PHILLIPS SS SCREW

(B)    6-32 X 1/2” SNAKE EYE SCREW

(C)    KEY FOR TAMPER SNAKE EYE SCREW

5| 60-68D05768D057| METAL PUSHBUTTON
COMPATIBLE MOUNTING BOXES OPTION

ITEM NUMBER

| PART NUMBER|

DESCRIPTION

FOR SINGLE GANG
 |

CM-34AL

| SURFACE BOX, STANDARD DEPTH, THREADED CONDUIT ENTRY. HEAVY DUTY CAST ALUMINUM

2 3/4”W x 4 1/2”H x 1 3/4”D (70mm x 114mm x 45mm)

CM-34BL

| ONE GANG BLACK ABS BOX, SURFACE MOUNT

2 7/8’’W x 4 5/8’’H x 1 3/4’’ D (73mm x 117mm x 44mm)

CM-66

| FLUSH BOX & DRESS PLATE, STANDARD DEPTH BOX WITH 7’’ x 7’’ (178mm x 178mm) DRESS PLATE HEAVY GAUGE STAINLESS STEEL
FOR MULLION|

CM-23D

| SURFACE BOX WITH EXTRA DEPTH, FLAME, AND IMPACT RESISTANT BLACK POLYMER (ABS) 1 3/4” W X 4 1/2”H X 1 3/4”D (46MM X 117MM X 43MM)

Opening New Doors to Innovation, Quality and Support

Call: 1.877.226.3369 / 905.366.3377
Visit: www.camdencontrols.com
File: CM-221M_Manual.indd
Revision: 04/04/22
Part No.: # 40-82B308

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>