STAYER BPB32 L20 Brushless Instruction Manual

STAYER BPB32 L20 Brushless

Product Information

The BPB32 L20 BRUSHLESS is a product manufactured by Grupo Stayer and conforms to the following standards:

• EN 62841-1
• EN 55014-1
• EN 55014-2
• EN ISO 12100
• EN 61000-3-2
• EN 61000-3-3
• EN 60335-2-29

The product also complies with the regulations 2006/42/EC, 2014/30/EU, and 2011/65/EU.

The BPB32 L20 has the following technical specifications:

• Battery Type: Li-ion
• Voltage: 18 Vdc
• Battery Capacity: 2.0 – 6.0 Ah
• Charging Time: 60 minutes
• Speed: n0 – c/s (rpm)
• Sound Pressure Level: LPA dB(A)
• Sound Power Level: LWA dB(A)
• Weight: 1.4 kg
• Dimensions: 67 mm

Product Usage Instructions

To use the BPB32 L20 BRUSHLESS product, follow these steps:

1. Charge the Li-ion battery fully before use, which takes about 60 minutes.
2. Insert the battery into the product and ensure it is securely attached.
3. Press the power button to turn on the product.
4. Adjust the speed of the product using the n0 – c/s (rpm) control according to your needs.
5. After use, turn off the product and remove the battery from the product.
6. Store the product and battery in a safe and dry place away from children and pets.

We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents: EN 62841-1, EN 55014-1, EN 55014-2, EN ISO 12100, EN 61000-3-2, EN 61000-3-3, EN 60335-2-29 according to EU Regulations 2006/42/EC, 2014/30/EU, 2011/65/EU.

This manual is consistent with the date of manufacture of your machine, you will find information on the technical data of the machine acquired manual check for updates of our machines on the website: www.grupostayer.com

DATA SHEET

MACHINE SPECIFIC SAFETY WARNINGS

• Use the tool only for pruning branches. Do not use it for other tasks.
• Never allow children or persons with disabilities of any kind, as well as inexperienced persons to use this tool. Failure to do so could result in injury.
• Carefully read the instructions and specifications of the battery you use with the tool. Failure to do so could result in poisoning or injury when applying the product.
• Always maintain a stable and balanced position. Do not reach into hard-to-reach areas or work in awkward positions.
• Do not touch the scissor blades unless the battery is disconnected. Failure to do so could result in injury.
• Do not attempt to cut materials other than branches. Cutting materials not intended for this tool may cause the shears to jam. If this happens, disconnect the battery and only then remove the jammed material.
• Do not hold the branch to be cut with the hand that is not holding the tool. For your safety always keep your hand away from the cutting area and the tool.
• Do not force the tool to cut beyond its capabilities. The tool could slip and cut other things or injure you.
• Avoid cutting any type of electrical wiring. Risk of electrocution.
• Handle the blades with extreme care. They are extremely sharp and the tool is very powerful.
• Always examine the blades before starting any work. Bad or damaged blades can cause accidents.
• After completing any work, switch the tool off at the safety switch and disconnect the battery.

BATTERIES USE AND CARE

• Do not open the battery. Danger of shortcircuiting.
• Protect the battery against heat, e. g., against continuous intense sunlight, fire, water, and moisture. Danger of explosion.
• In case of damage and improper use of the battery, vapours may be emitted. Provide for fresh air and seek medical help in case of complaints. The vapours can irritate the respiratory system.
• Use the battery only in conjunction with your STAYER power tool. This measure alone protects the battery against dangerous overload.
• Use only original STAYER batteries with the voltage listed on the nameplate of your power tool. When using other batteries, e. g. imitations, reconditioned batteries or other brands, there is danger of injury as well as property damage through exploding batteries.
• Do not continue to press the On/Off switch after the machine has been automatically switched off. The battery can be damaged.
• The battery is equipped with a temperature control which allows charging only within a temperature range of between 0 °C and 45 °C. A long battery service life is achieved in this manner.
• Observe the notes for disposal.
• Use only the battery chargers listed on the accessories page. Only these battery chargers are matched to the lithium-ion battery of your power tool.
• The battery is supplied partially charged. To ensure full capacity of the battery, completely charge the battery in the battery charger before using your power tool for the first time.
• The lithiumion battery can be charged at any time without reducing its service life. Interrupting the charging procedure does not damage the battery.
• The lithiumion battery is protected against deep discharging. When the battery is empty, the machine is switched off by means of a protective circuit: The inserted tool no longer rotates.
• Temperature Dependent Overload Protection
• When using as intended for, the power tool cannot be subject to overload. When the load is too high or the allowable battery temperature range of 0–50 °C is exceeded, the speed is reduced. The power tool will not run at full speed until reaching the allowable battery temperature. position. Unintentional actuation of the On/Off switch can lead to injuries.
• Open the keyless chuck 2 by turning in rotation direction , until the tool can be inserted. Insert the tool. Firmly tighten the collar of the keyless chuck 2 by hand in rotation direction . This automatically locks the drill chuck.
• The locking is released again to remove the tool when the collar is turned in the opposite direction.

FUNCTIONAL DESCRIPTION

PLACING OR FIXING THE TOOL
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

PRODUCT FEATURES
The numbering of the product features refers to the illustration of the machine on the graphics page.
Screwdriver bit

1. Lower blade
2. Upper blade.
3. Hexagonal screw.
4. Trigger.
5. Tightening nut.
6. Safety switch I | O
7. Battery
8. Battery release button
9. Hexagon spanner
10. Lubricant
11. Internal hex spanner

ASSEMBLY

Battery charging
Use only the battery chargers listed on the accessories page. Only these battery chargers are matched to the lithium-ion battery of your power tool.

Note: The battery is supplied partially charged. To ensure full capacity of the battery, completely charge the battery in the battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without reducing its service life. Interrupting the charging procedure does not damage the battery.
Do not continue to press the On/Off switch after the machine has been automatically switched off. The battery can be damaged.
To remove battery 5, press the battery unlocking button 9 and pull the battery out of the power tool toward the rear. Do not exert any force.
The battery is equipped with an NTC temperature control which allows charging only within a temperature range of between 0º C and 45º C. A long battery service life is achieved in this manner.
Observe the notes for disposal.

TOOL ASSEMBLY
Changing the Upper blade (2)

1. Follow the steps described in point 3 of the manual to activate the tool by opening the blades.
2. With the blades open, deactivate the safety switch (6) leaving it in position O and remove the battery (7).
3. Remove the hexagonal screw (3) by turning anticlockwise using the hexagonal spanner (9). Then remove the hexagonal nut (5) by also turning anticlockwise. Remove the washer.
4. Use the hexagonal spanner (9) to unscrew the 2 screws that hold the head housing, extracting the part that covers the blade insert.
5. Remove the retaining ring (A) from the retaining arm (B) using pliers. With blade (2) released, you can remove it and install a new one by following this sequence of steps in reverse.
6. Apply lubricant (10) to the new blade (2). When installing the housing part, make sure that it is aligned with the rest of the structure and that the fastening screws fit correctly. Before using the tool, make sure that the pressure between the blades is correct.

CAUTION: Use only original STAYER spare parts. The use of other components can lead to accidents and injuries.
Adjusting the pressure between the blades (1-2)
It is necessary to adjust the pressure between the blades from time to time in order to keep the tool in good working conditions.

1. Follow the steps described in point 3 of the manual to activate the tool by opening the blades.
2. With the blades open, deactivate the safety switch (6) leaving it in position O and remove the battery (7).
3. Loosen the hexagonal screw (3) by turning anticlockwise using the hexagonal spanner (9).
4. Adjust the pressure of the blades (1-2) using the internal hexagonal spanner (11). Increase the pressure by turning clockwise, release the pressure by turning anticlockwise.
5. Reassemble the machine by repeating steps 1, 2 and 3 in reverse order.

CAUTION: Correct blade pressure is a decisive factor in the performance of the tool.
If the blades are too loose, the cut will be of poor quality and the branch debris will get stuck in the blades.
Excessive pressure will strain the tool’s motor and reduce the tool’s life and wear the blades.
When the shears are closed there should be no gap or movement between the blades.

Greasing the blades (1-2)
The blades must be greased before each use.

1. Follow the steps described in point 3 of the manual to activate the tool by opening the blades.
2. With the blades open, deactivate the safety switch (6) leaving it in position O and remove the battery (7).
3. Remove the hexagonal screw (3) by turning anticlockwise using the hexagonal spanner (9).
4. Apply lubricating oil (10) in the insertion hole of the hexagonal nut (5) where the screw (3) is inserted.
5. Screw the screw (3) back into position by turning clockwise.
6. Operate the trigger (4) several times under vacuum to redistribute the oil correctly.
   Note: Do not use too much oil, apply it carefully.

USE

CONNECTION

1. Insert a charged battery (7) into the tool.
2. Activate the safety switch (6) by turning it to position I. The machine will beep twice to indicate that it is activated.
3. Press the trigger (4) twice in succession to unlock the safety mechanism. The blades will open, leaving the tool ready for use.
4. Press the trigger (4) once for each cut you wish to make.

DISCONNECTING

1. Press the trigger (4) for 3 seconds at a time. This will cause the scissors to close and emit 2 sounds indicating that it has been locked with the safety system.
2. Deactivate the safety switch (6) by turning it to the O position. The tool will emit a sound indicating that it has been deactivated.
3. Disconnect the battery (7) using the disconnect button (7).

SAFETY LOCK
Even if a battery (7) is connected to the tool with the blades open and the safety switch (6) in position I for activation, the tool will not operate until a safety release is completed.
To reactivate the tool in this situation, press the trigger (4) twice quickly and then press it once more.

AUTOMATIC SHUT-OFF
If the tool remains switched on for more than 10 minutes without activity it will go into automatic shutdown mode.
To restart the tool, deactivate the safety switch (6) by turning it to position O, and then turn it back to position I. Then press the trigger (4) twice quickly to unlock the tool.
WORKFLOW

With the tool switched on and activated, press the trigger (4) once for each cut you wish to make.

MAINTENANCE AND SERVICE

MAINTENANCE AND CLEANING

Before any work on the machine (e. g., maintenance, tool change, etc.) as well as during transport and storage, set the rotational direction switch to the centre position.Unintentional actuation of the On/Off switch can lead to injuries.
For safe and proper working, always keep the machine and ventilation slots clean.
When the battery is no longer operative, please refer to an authorised aftersales service agent for Stayer power tools.
If the machine should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an aftersales service centre for Stayer power tools.

Cleaning the blades (1-2)

1. Follow the steps described in point 3 of the manual to activate the tool by opening the blades.
2. With the blades open, turn the safety switch (6) to the O position and remove the battery (7).
3. Use a wire brush to remove any dirt from the blades.
4. Carefully clean the blades using a cloth rag, applying lubricating oil (10).

Sharpening the blades (1-2)

1. Follow the steps described in point 3 of the manual to activate the tool by opening the blades.
2. With the blades open, deactivate the safety switch (6) leaving it in position O and remove the battery (7).
3. Use a flat file (L) to file the cutting edge of the blade (1 or 2). Sharpen the blade by following the curve of the blade longitudinally, maintaining the angle of the file throughout the entire stroke.
4. Use a flat file to file the opposite edge of the blade (1 or 2). File the blade by applying light pressure following the curve of the blade longitudinally while maintaining the angle of the file throughout. Do not sharpen this side of the blade too much or the gap between the blades will be too wide and the blades will lose effectiveness.

TRANSPORT

he contained lithiumion batteries are subject to the Dangerous Goods Legislation requirements. The user can transport the batteries by road without further requirements. When being transported by third parties (e.g.: air transport or forwarding agency), special requirements on packaging and labelling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is required.
Dispatch batteries only when the housing is undamaged. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. Please also observe possibly more detailed national regulations.

DISPOSAL

The machine, accessories and packaging should be sorted for environmental- friendly recycling.

Only for EC countries:
Do not dispose of power tools into house-hold waste!

According the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that a re no longer usa-ble must be collected separately and disposed of in an environmentally correct manner.

Battery packs/batteries: Li-Ion:
Please observe the instructions in section
“Transport”. Do not dispose of battery packs/batteries into household waste, fire or water. Battery packs/batteries should be collected, recycled or disposed of in an environmental-friendly manner.
Only for EC countries:
Defective or dead out battery packs/batteries must be recycled according the guideline 2006/66/CE

TECHNICAL SPECIFICATIONS

The values given are valid for nominal voltages [U]230/240 V-50/60 Hz – 110/120 V – 60Hz. For lower voltage and models for specific countries, these values can vary.

INFORMATION ON NOISE AND VIBRATIONS

Wear hearing protection!
Measured values established in accordance with EN 62841-1.
The technical specifications indicated here are understood within certain tolerances (in accordance with the standards currently in force).

WARRANTY GENERAL CONDITIONS

In the STAYER IBERICA GROUP S.A. (from now on “STAYER”), strict control processes are conducted to comply with the security and quality required.
To understand the application area of this text, we differentiate the following users:
– Users or consumers, as private individuals whose acts are not related to their main comercial, business activity or their main profession or trade. Legal persons and entities without legal personality which act with non-profit means in an unrelated comercial or corporate enviroment.
– Professionals, whom obtain comercial, business or working profits by using any STAYER product.
STAYER offers a guarantee for all of its power tools, garden tools and welding tools, subject to the following conditions:

1. STAYER offers a 36 month guarantee against manufacturing defects or consistency issues, bearing in mind that any issue must be easily visible or provable, as the product will be tested at our labs to verify said issues. If the product has been subjected to industrial or professional use, said guarantee will cover exclusively 12 months since the first buyer aquired the product.
2. The following cases are exempt from the guarantee:
   • Any kind of defect or malfunctioning caused by not applying the safety and maintenance instructions given in the User’s guide.
   • Any damage caused by using other brand’s accessories, incompatible accessories with the tool model or faulty accessories.
   • Any manipulation, modification or repair conducted by staff unrelated to STAYER or its associated Technical Support Services.
   • Products with minimal deviations from the features that do not impact on the tool’s optimal performance and its value.
   • Products which have been connected to a different voltage tenssion grid than the one stated on the tool’s features, causing an electrical failure.
   • Products or components which have suffered wear due to the normal use of the tool, being said components consumables, accessories or components subject to wear that must be replaced by the owner.
   • Products that show any kind of misuse or application which deviates from its original intended uses, listed in the Users guide.
   • Products that show lack of correct maintenance from the owner. The owner is responsible for the tool’s maintenance in order to preserve its service life.
   • Accessories and tool consumables, as their intended use has a limited service life that includes wear.
3. In order to claim the guarantee rights, the tool owner must first fill the repair order either digitally or physically, and process it with the tool’s vendor or the Authorized Technical Support Services before shipping the tool. A copy of the purchase receipt or invoice must be attached to the form where the purchase date can clearly be seen. Shipping costs are not included if the product is delivered to the vendor or the Technical Support Services without processing the repair form first.
4. If the Authorized Technical Support or STAYER is unable to locate the defect or issue, STAYER will not assume the shipping costs, nor the costs derived from testing the tool to locate the issue.
5. Guarantee transfer is completely forbidden, the guarantee does not cover second-hand products.
6. During the guarantee application due to manufacturing defects or consistency issues, the product will remain under STAYER’s custody in its facilities or its Authorized Technical Support Services. During this period of time the tool’s owner is not entitled to receive a substitution tool in place of the product that is being repaired.
7. In order to correct the manufacturing defects or consistency issues contemplated in the guarantee terms, STAYER will only repair or substitute all the necessary components free of charge in order for the tool to perform according to the quality and safety standards. STAYER withholds the right to substitute the product for a similar one in cases where reparations would not be possible.
   You can find this information in other languages at: https://www.stayer.en/

Área Empresarial Andalucía – Sector I Calle Sierra de Cazorla nº7

C.P: 28320 Pinto (Madrid) SPAIN

info@grupostayer.com
www.grupostayer.com

References

• Inicio - Grupo Stayer
• STAYER - Herramientas y maquinaria diseñadas para profesionales

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>