FEIT electric SYW-SYNCSOLAR4 Solar LED Square Lantern User Manual

FEIT electric SYW-SYNCSOLAR4 Solar LED Square Lantern User Manual

Safeg Information

READ BEFORE INSTALLATION AND SAVETHESE INSTRUCTIONS

CAUTION : Contains one 18650 rechargeable lithium-Ion battery. Risk of fire, explosion, or burns. Do not disassemble. Do not crush or damage the battery. Do not heat or incinerate. Do not open or disassemble. Do not make modifications to this product.

WARNING : RF Exposure. The equipment has been evaluated to meet general RF exposure requirement. The device can be used in portable condition without restriction.

WARNING : Dispose of used battery promptly according to local recycling or waste regulations. Keep battery out of reach of children and its original package until ready to use. Clean battery contacts and unit contacts prior to installing new battery. Ensure that the battery is installed correctly with regard to polarity (+ and

HOW SOLAR LIGHTS WORK:
Solar panels convert sunlight into electricity. During the day, while the sun is shinning, electricity converted by the solar panel is stored in the rechargeable battery. At night, the solar light is powered by the battery using the electricity stored during the day. The operating time depends on geographical location, daily weather conditions and season.

CHOOSING THE RIGHT LOCATION:
It is important to select a location with as much sunlight as possible. Shady areas will not allow the battery to be fully charged and will reduce the nighttime working hours. Be sure that the selected location is not close to other nighttime light sources such as streetlights or porch lights. These light sources may keep the solar lights from turning on automatically.

DUSK TO DAWN OPERATION:
This product is designed to only operate at night. The light will remain off during the day and turn on automatically at dusk and remain on for up to six hours.

NOTE : To make sure this function works properly, the switch must be in the selected color position.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. CAN ICES-005 (B).

Supplier’s Declaration of Conformity:
47 CFR § 2.1077 Compliance Information Responsible Party:

Feit Electric Company
4901 Gregg Road, Pico Rivera, CA 90660, USA

Unique Identifier:
LAN4SD/SYNC/S0L/BZ (L)

Limited Warrang

This product is warrantied to be free from defects in workmanship and materials for up to 2 years from date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com, visit feit.com/contact-us or call 1-866-326-BULB (2852) for instructions on replacement or refund. REPLACEMENT 0R REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL 0R CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not app ly to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

Pre-Installation

TOOLS REQUIRED

HARDWARE INCLUDED

NOTE : Hardware not shown to actual size.

Pre-Charge

1. For best pe%ormance, charge the unit for two (2) days prior to use
   • Remove the insulating tab.
   • In order to properly charge, the unit must be turned OFF. Use the 0n/0ff/Cycle button to cycle through all of the colors (Soft White, Bright White, Cool White, Daylight, Deluxe Daylight, Red, Blue, Green, Yellow, Orange, Purple, Teal, and Pink) and reach the OFF position .
   • Select a location with as much sunlight as possible.
   • After the unit has charged in the sun for two (2) days, turn it back on by pressing the 0n/0ff/Cycle button and selecting the color of your choice. If there is daylight outside, it will stay on for about 10 – 20 seconds and then turn off. If it is nighttime, the unit will remain on.
     

Installation

1. Peel oh sticker from solar panel and remove insulating tab
   • Peel off the sticker from the solar panel.
   • Remove the insulating tab.
   • It is recommended that you charge the unit for two (2) days before use to adequately charge the battery, following the Pre-Charge instructions.
2. Installing the solar lantern
   • Place the solar lantern (AA) in the desired location, and ensure that the solar panel is in direct sunlight. Can be hung on a Shepherd’s Hook (sold separately), or placed on a table or fence pos

Operation without Remote

This Onesync Lantern works on its own or with the provided remote. It also can be controlled via WiFi with the smart bridge (sold separately).

DUSK TO DAWN OPERATION:
The unit will automatically turn on at dusk and remain on through the night for 6 hours. The unit will remain off throughout the day, until dusk. NOTE: To make sure this function works properly, always have the switch in the ‘0N’ position (including daytime).

1. Turning on the Lantern
   Turn the Solar Lantern (AA) on by pressing the button on the top of the unit

2. Selecting a Color
   To cycle through the colors, push the button. Colors are: Soft White, Bright White, Cool White, Daylight, Deluxe Daylight, Red, Blue, Green, Yellow, Orange, Purple, Teal, Pink. The lantern will remember the color setting when next turned on.
   
   IMPORTANT : Light brightness is determined by the charge level of the batteries. Brightness will decrease during operation to extend battery life.
   IMPORTANT : Selecting a color, other than white, will extend battery life.

3. Functioning Dusk to Dawn

   • The Dusk to Dawn sensor is built into the unit.

Operation with Remote scold separately)

Operating with a 0neSync remote allows for expanded control. Modify settings of individual 0neSync units or multiple units in groups. The 0neSync remote has a 100ft control range and will command all paired units within 100ft of the remote. All 0neSync units are equipped with a signal repeater that will repeat any remote commands to all other units within 100ft. Placing units within 100ft of at least one other unit creates a control network and allows for unlimited remote control range, as long as there is a functioning 0neSync unit within 100ft to relay the command.

Example: You can install a 0neSyns unit, then another 0neSync unit 100ft away from the first unit. Continue to install 3 more 0neSync units in this way so that the last unit is 500ft away. Using this relay technology, the remote will control the farthest unit that is 500ft away.

1. Entering pairing mode
   • Hold down the pairing button on the unit for 3 seconds. Once the solar lantern (AA) starts to blink slowly, it will be in pairing mode for 3 minutes until successfully grouped or timed out.
2. Pairing the remote to the Lantern
   • While the solar lantern is in pairing mode, press and hold the desired Groups button (1, 2, 3, 4, 5 or 6) for 3 seconds to pair the remote to the selected group. The light will flash to indicate successful pairing and the unit will exit pairing mode.
     NOTE : A 0neSync unit can be paired to multiple remote groups at once.
     

Unpairing the Lantern from the remote

• To unpair, first follow step 1 so that the unit is in pairing mode. Once the unit is in pairing mode, press the group button you wish to unpair from and then hold the remote power button for 3 seconds. The light will flash to indicate successful unpairing and the unit will exit pairing mode.
• To unpair from all groups at once, hold down the button on the 0neSync unit for 10 seconds. It will flash three times rapidly to indicate that that all groups have been unpaired from the unit.

NOTE : The remote is equipped with a universal Group #1. To create unique groups, pair using Groups #2-6. All unik pre-paired to the universal Group #1 so that they will immediately respond with any remote Group #1 command. To remove the unit from the universal group, follow the unpairing instructions in Step 3.

DUSK TO DAWN OPERATION:
The light will automatically turn on at dusk and remain on through the night for 6 hours. The light will remain off throughout the day, until dusk.

IMPORTANT : Light brightness is determined by the charge level of the batteries. Brightness will decrease during operation to extend battery life.

IMPORTANT : Selecting a color, other than white, will extend battery life.

Operation with Smart Bridge

1. Downloading and installing the Feit Electric app
2. Search for the Feit Electric app in the App Store or Google Play Store.
3. Download and Install the Feit Electric app on your smart unit. Connect to a 2.4GHz Wi-Fi network that covers your installation location.
4. Follow the instructions in the Feit Electric app & Smart Bridge manual to pair your 0neSync lights.

Feit Electric App

Babery Replacement

1. Replacing the baflery
   To replace the rechargeable battery, remove the lid by unscrewing the (2) lid screws using a Phillips head screwdriver.

2. Replace with a new lithium-ion 18650 2600mAh 3.6V minimum 9.36Wh or greater. Install battery correctly with regard to the polarity (+ and -).

3. Reattach the lid by securing the (3) screws using a Phillips head screwdriver.
   

WARNING : Install battery correctly with regard to the polarity (+ and -)

Troubleshooting

PROBLEM : POSSIBLEE CAUSES : CORRECTIVE ACTION

The unit will not turn on.| The battery is not making contact.| Loosen the battery cover screws, pull out the battery cover and inspect the battery connection. After inspect on, reinsert the battery.
The battery is not fully charged.| Ensure the solar panel is positioned in a location that prov des full and direct sunlight. If installed in a shady area, the battery will take a longer time to charge, and may not fully charge, and reduce working hours.
The panel is near an external light source that is inadvertently triggering the dusk to dawn sensor.| Relocate the panel to an area that does not have any external light sources or remove the external light sources from the panel’s proximity.
The units go out too early.| The battery charge is low.| Allow the batteries to get a full charge by power!ng off the unit for 1-2 days. Or relocate the unit to an area with direct sunlight. Check panel for dirt, damage, or light obstruct on.
The unit turns on and off continuously.| The solar panel is near an external light source that is inadvertently triggering the dusk to dawn sensor.| Relocate or shield the solar panel so that external light sources do not shine directly on it.
The unit turns on for 10 – 20 seconds and then turns off.| The dusk to dawn sensor is turning the unit off. This will happen during daytime.| The unit should automatically turn on at dusk.

Questions, problems, missing pads?
Before returning to store, visit feit.com/help for further assistance.

FEIT ELECTRIC COMPANY I PICO RIVERA, CA I www.feit.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>